rear stay assembly - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

RedSled · 04-19-2020, 07:04 PM

hi good day, need some input as to why the rear stay assembly bends on s13 rear suspension ,I've replaced them already and well was doing some work on the rear an noticed these slightly bent again ,this is the part that acts as the front washer for the bushings on the subframe and also connect to the chassis .

samotage · 04-19-2020, 07:20 PM

Are your subframe bushings munted? You can tell if you have axle tramp. If so the subframe will slop about, and likely bend these stays.

Sent from my iPad using Tapatalk

RedSled · 04-19-2020, 07:36 PM

Quote:

Originally Posted by samotage

Are your subframe bushings munted? You can tell if you have axle tramp. If so the subframe will slop about, and likely bend these stays.

Sent from my iPad using Tapatalk

Got spl solid bushings even the diff has solid bushings

samotage · 04-19-2020, 08:57 PM

How much power? Is the chassis twisting?

Sent from my iPad using Tapatalk

RedSled · 04-19-2020, 09:32 PM

Isn't this normal for s13 ? cause when I was getting a replacement, there were a lot of bent ones

SupaDoopa · 04-20-2020, 06:24 AM

Are you bending the arm of the little tabs that come off the rear subframe that the bolt goes through to secure the arm or literally the whole control arm itself?

RedSled · 04-20-2020, 08:15 AM

Quote:

Originally Posted by SupaDoopa

Are you bending the arm of the little tabs that come off the rear subframe that the bolt goes through to secure the arm or literally the whole control arm itself?

just the little arms

RedSled · 04-20-2020, 08:18 AM

actually both gets slightly bent ,but the one I'm seeing the bends are the ones bolting directly under the subframe bushings

SupaDoopa · 04-20-2020, 02:01 PM

The fuck is a 'little arm?' Take a picture.

04-19-2020, 07:04 PM	#1
RedSled Leaky Injector Join Date: Mar 2007 Location: chilling Posts: 106 Trader Rating: (3) Feedback Score: 3 reviews	rear stay assembly hi good day, need some input as to why the rear stay assembly bends on s13 rear suspension ,I've replaced them already and well was doing some work on the rear an noticed these slightly bent again ,this is the part that acts as the front washer for the bushings on the subframe and also connect to the chassis .

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

04-19-2020, 07:20 PM	#2
samotage BANNED Join Date: Oct 2018 Location: Melbourne Posts: 88 Trader Rating: (0) Feedback Score: 0 reviews	Are your subframe bushings munted? You can tell if you have axle tramp. If so the subframe will slop about, and likely bend these stays. Sent from my iPad using Tapatalk

04-19-2020, 08:57 PM	#4
samotage BANNED Join Date: Oct 2018 Location: Melbourne Posts: 88 Trader Rating: (0) Feedback Score: 0 reviews	How much power? Is the chassis twisting? Sent from my iPad using Tapatalk

04-19-2020, 09:32 PM	#5
RedSled Leaky Injector Join Date: Mar 2007 Location: chilling Posts: 106 Trader Rating: (3) Feedback Score: 3 reviews	Isn't this normal for s13 ? cause when I was getting a replacement, there were a lot of bent ones

04-20-2020, 06:24 AM	#6
SupaDoopa Post Whore! Join Date: Jan 2010 Location: 隠された意図 Age: 33 Posts: 3,502 Trader Rating: (26) Feedback Score: 26 reviews	Are you bending the arm of the little tabs that come off the rear subframe that the bolt goes through to secure the arm or literally the whole control arm itself?

04-20-2020, 08:18 AM	#8
RedSled Leaky Injector Join Date: Mar 2007 Location: chilling Posts: 106 Trader Rating: (3) Feedback Score: 3 reviews	actually both gets slightly bent ,but the one I'm seeing the bends are the ones bolting directly under the subframe bushings

04-20-2020, 02:01 PM	#9
SupaDoopa Post Whore! Join Date: Jan 2010 Location: 隠された意図 Age: 33 Posts: 3,502 Trader Rating: (26) Feedback Score: 26 reviews	The fuck is a 'little arm?' Take a picture.