Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > Local / Regional / National > Europe

Europe A place for our cousins from across the pond


Reply
 
Thread Tools Display Modes
Old 09-08-2020, 07:10 AM   #1
Dustyx77
 
Join Date: Mar 2020
Location: Norway
Age: 23
Posts: 3
Trader Rating: (0)
Dustyx77 is an unknown quantity at this point
Feedback Score: 0 reviews
The blow off valve issue

Hey guys, sooo I've bought a 200sx (eurospec) s14 that used to run on 24psi of boost, but the blow off valve, atleast according to the internet, is rated for 26psi. Sooo long story short, the car has still some major compressor surge sounds. I barely use full throttle because I use the car on the street. What kind of psi blow off valve spring would you guys suggest?
Dustyx77 is offline   Reply With Quote
Sponsored Links
Old 09-13-2020, 06:39 AM   #2
S14rebuild
BANNED
 
Join Date: May 2019
Location: Florida-FAIL
Posts: 2,497
Trader Rating: (8)
S14rebuild S14rebuild S14rebuild S14rebuild S14rebuild S14rebuild S14rebuild S14rebuild S14rebuild S14rebuild S14rebuild
Feedback Score: 8 reviews
If ur getting surge then the bov isnt opening or its too small.

First check your vacuum line to it. Should be a direct feed from intake manifold to the bov, not "teed" off another line.

Then make sure it acually opens, not stuck or damaged.
S14rebuild is offline   Reply With Quote
Old 09-14-2020, 10:48 AM   #3
TheRealSy90
Premium Member
 
TheRealSy90's Avatar
 
Join Date: Mar 2009
Location: Maricopa, AZ
Age: 30
Posts: 7,679
Trader Rating: (10)
TheRealSy90 has a brilliant futureTheRealSy90 has a brilliant futureTheRealSy90 has a brilliant futureTheRealSy90 has a brilliant futureTheRealSy90 has a brilliant futureTheRealSy90 has a brilliant futureTheRealSy90 has a brilliant futureTheRealSy90 has a brilliant futureTheRealSy90 has a brilliant futureTheRealSy90 has a brilliant futureTheRealSy90 has a brilliant future
Feedback Score: 10 reviews
Your bov is probably set stiff so that it only fully opens if you were at full boost, and anything under that when cruising around it just stays closed.
__________________
Quote:
Originally Posted by crimsonrockett View Post
Such a good signature.
TheRealSy90 is offline   Reply With Quote
Old 12-16-2020, 09:27 PM   #4
Kingtal0n
Post Whore!
 
Kingtal0n's Avatar
 
Join Date: Jul 2005
Location: South Florida
Age: 38
Posts: 4,648
Trader Rating: (17)
Kingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond repute
Feedback Score: 17 reviews
Send a message via AIM to Kingtal0n
The correct type of bypass for a turbo will hang open at idle, like the stock bov.

The best thing for the turbo is to be able to instantly relief any air, from using a very easy to open bov style.

The reason people don't like to use the correct type of bov on their cars is often because they do not have a recirculated bov style.
In other words, you need the bov to recirculate the air back to the intake (pre turbo) just like FACTORY does, or else, the maf will dump extra rich fuel into the engine whenever the bov opens.

I suggest looking at the factory bov setup, the bypass style. See if you can get a BYPASS style bov. For example greddy type-s was a bypass style bov.
Always put the bov as close to the turbo as possible. Never put it after an intercooler either.

If you get bypass style bov, you can use a very easily to open bov, so the turbo will never be in *pain*.
If you cannot get the bypass style, then the best alternative solution (used to be) is HKS SSQV placed right near the turbo (within 1-2 feet or so). It won't open at idle and it will cause a little surge (a little delay to open) but it won't cause MAF issues when vented to atmosphere much either.
__________________
5.3/4l80e/turbo 240sx playthrough:
https://tinyurl.com/turbo240
Kingtal0n is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 07:14 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™