WTB: Sr20det redtop crankshaft - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

wh18skal · 08-29-2019, 04:01 PM

Need a Sr20det crankshaft, spun a rod and got a .25 oversized bearing in spec after clean up of the crank, but to be honest I’m scared to run it, I don’t want it to spin again this being the second time on the same rod however the first time was from previous owner. If anyone can help would be greatly appreciated. Thanks

wh18skal · 09-11-2019, 03:20 AM

Bump

Sent from my iPhone using Tapatalk

abaron13 · 09-12-2019, 12:08 PM

I have one, but I'm in Cleveland Ohio and the shipping would probably be insane. Came out of an engine with a melted piston.

joaquin714 · 09-12-2019, 12:35 PM

Did you remachine the rod as well when you first spun a bearing?

wh18skal · 09-12-2019, 12:37 PM

No

Sent from my iPhone using Tapatalk

joaquin714 · 09-12-2019, 02:10 PM

It could have been out of spec. Possible what caused your bearing to fail again.

wh18skal · 09-12-2019, 03:20 PM

Yeah it definitely crossed my mind, once I get a new crankshaft and have a Machine shop check it, I’ll take out the piston and rod and have the rod checked as well

Sent from my iPhone using Tapatalk

08-29-2019, 04:01 PM	#1
wh18skal Join Date: Jul 2008 Location: ct Age: 34 Posts: 6 Trader Rating: (0) Feedback Score: 0 reviews	WTB: Sr20det redtop crankshaft Need a Sr20det crankshaft, spun a rod and got a .25 oversized bearing in spec after clean up of the crank, but to be honest I’m scared to run it, I don’t want it to spin again this being the second time on the same rod however the first time was from previous owner. If anyone can help would be greatly appreciated. Thanks

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-11-2019, 03:20 AM	#2
wh18skal Join Date: Jul 2008 Location: ct Age: 34 Posts: 6 Trader Rating: (0) Feedback Score: 0 reviews	Bump Sent from my iPhone using Tapatalk

09-12-2019, 12:08 PM	#3
abaron13 Zilvia Junkie Join Date: Mar 2011 Location: Cleveland Age: 29 Posts: 385 Trader Rating: (24) Feedback Score: 24 reviews	I have one, but I'm in Cleveland Ohio and the shipping would probably be insane. Came out of an engine with a melted piston.

09-12-2019, 12:35 PM	#4
joaquin714 Zilvia Member Join Date: Jul 2007 Location: California Posts: 178 Trader Rating: (1) Feedback Score: 1 reviews	Did you remachine the rod as well when you first spun a bearing?

09-12-2019, 12:37 PM	#5
wh18skal Join Date: Jul 2008 Location: ct Age: 34 Posts: 6 Trader Rating: (0) Feedback Score: 0 reviews	No Sent from my iPhone using Tapatalk

09-12-2019, 02:10 PM	#6
joaquin714 Zilvia Member Join Date: Jul 2007 Location: California Posts: 178 Trader Rating: (1) Feedback Score: 1 reviews	It could have been out of spec. Possible what caused your bearing to fail again.

09-12-2019, 03:20 PM	#7
wh18skal Join Date: Jul 2008 Location: ct Age: 34 Posts: 6 Trader Rating: (0) Feedback Score: 0 reviews	Yeah it definitely crossed my mind, once I get a new crankshaft and have a Machine shop check it, I’ll take out the piston and rod and have the rod checked as well Sent from my iPhone using Tapatalk