*ISIS S14 Dual N1 cat-back exhaust review - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

bshotts · 05-11-2009, 09:52 PM

The bulk of this text is taken from my review I posted directly on Enjuku’s website, however this includes pics. Enjoy!

I was looking for an S14 cat-back alternative to the outrageous prices of some of the well-known exhaust manufacturers. Asked Ken about the ISIS quality and if they've been satisfied with the products so far and was convinced to give this a try.

Exhaust arrived well-packed only with a few issues: unless they are still residing deep inside the bowls of the exhaust pipes, I didn't receive the gasket/hardware bag which may have just been a slip up; and the right 3.5" exhaust tip was slightly bent but was fixed by shaping it with a soft hammer and the included silencer to match the circular profile. Stainless looked pristine and I examined every weld for any slag or any area where the weld didn't achieve full penetration....couldn't find a single one! My dog's squirrel approves

Installation was straightforward but a bit of advice; start with the middle exhaust hanger on the rear section then move to the rearmost two near the bumper, then finish with the closest to the sway bar/diff. The middle hanger could stand to move 1 to 1.5" forward and the front hanger about 1" rearward. I moved on to the front section and bolted it to my Catco 3" cat while holding up the other end using an M10x1.50 bolt attached to the rear section. After I tightened up to the cat, I moved to the four bolts/nuts to join the front and rear sections, again using a total of four M10x1.50 bolts with a lock washer and flanged hex nuts. Because I didn't have a gasket, I used some high-temp red RTV but plan to fix this soon. Fitment to the OEM bumper is very nice and does not damage the paint. If there was an exhaust to OEM bumper thread, this would be the standard.

Exhaust note is surprisingly quiet especially at idle on my SR20 using a Tomei Expreme and 3" back exhaust, which is nice if you daily for more than 45 minutes to work each way like me. Climb in revs and you notice no rattling/raspiness and a full sounding grunt....makes good music with the turbo spool.

OEM S14 cat-back: 40 lbs.
ISIS S14 Dual N1 cat-back: 35 lbs.

grnappletree14 · 05-12-2009, 12:52 AM

good review !!!!!!!!!!!

Om1kron · 05-12-2009, 02:08 AM

looks real nice.

carps13guy · 08-22-2009, 01:26 PM

hey man, do you have any sound clips? im thinking of getting one for my s13

Ali 556 · 08-22-2009, 04:23 PM

good review,

but i think it's a Little close to the bumber and the stock bumber might melt from the heat

btw how much $$$?

bshotts · 08-23-2009, 05:44 AM

I've got a sound clip for ya....well except for the fact that I can't get the 3gp format to upload correctly. Tell you what, give me an email addy and I won't hesistate to get it to you.

Price for this particular exhaust was a (stainless) steal in my opinion (pun intended); roughly 300 shipped from Enjuku.

Ali 556 · 08-23-2009, 07:24 AM

Quote:

Originally Posted by bshotts

I've got a sound clip for ya....well except for the fact that I can't get the 3gp format to upload correctly. Tell you what, give me an email addy and I won't hesistate to get it to you.

.

[email protected]

Send and i'll upload and post a link to youtube

Blacksilvy · 01-22-2011, 08:27 PM

i hate to revive an old thread but is this exhaust no longer available now?

bshotts · 01-24-2011, 09:56 AM

Not sure if Enjuku still offers this, but I am currently offering it up for sale. I'm going more of an OEM route. Here's my FS link: http://zilvia.net/f/sale-items/36129...pe-lookie.html

05-11-2009, 09:52 PM	#1
bshotts Zilvia Junkie Join Date: Jan 2003 Location: Indianapolis, IN Age: 38 Posts: 472 Trader Rating: (13) Feedback Score: 13 reviews	ISIS S14 Dual N1 cat-back exhaust review The bulk of this text is taken from my review I posted directly on Enjuku’s website, however this includes pics. Enjoy! I was looking for an S14 cat-back alternative to the outrageous prices of some of the well-known exhaust manufacturers. Asked Ken about the ISIS quality and if they've been satisfied with the products so far and was convinced to give this a try. Exhaust arrived well-packed only with a few issues: unless they are still residing deep inside the bowls of the exhaust pipes, I didn't receive the gasket/hardware bag which may have just been a slip up; and the right 3.5" exhaust tip was slightly bent but was fixed by shaping it with a soft hammer and the included silencer to match the circular profile. Stainless looked pristine and I examined every weld for any slag or any area where the weld didn't achieve full penetration....couldn't find a single one! My dog's squirrel approves Installation was straightforward but a bit of advice; start with the middle exhaust hanger on the rear section then move to the rearmost two near the bumper, then finish with the closest to the sway bar/diff. The middle hanger could stand to move 1 to 1.5" forward and the front hanger about 1" rearward. I moved on to the front section and bolted it to my Catco 3" cat while holding up the other end using an M10x1.50 bolt attached to the rear section. After I tightened up to the cat, I moved to the four bolts/nuts to join the front and rear sections, again using a total of four M10x1.50 bolts with a lock washer and flanged hex nuts. Because I didn't have a gasket, I used some high-temp red RTV but plan to fix this soon. Fitment to the OEM bumper is very nice and does not damage the paint. If there was an exhaust to OEM bumper thread, this would be the standard. Exhaust note is surprisingly quiet especially at idle on my SR20 using a Tomei Expreme and 3" back exhaust, which is nice if you daily for more than 45 minutes to work each way like me. Climb in revs and you notice no rattling/raspiness and a full sounding grunt....makes good music with the turbo spool. OEM S14 cat-back: 40 lbs. ISIS S14 Dual N1 cat-back: 35 lbs. Last edited by bshotts; 05-12-2009 at 06:35 AM..*

05-12-2009, 02:08 AM	#3
Om1kron Post Whore! Join Date: Sep 2004 Location: Simi Valley, CA Age: 40 Posts: 6,879 Trader Rating: (15) Feedback Score: 15 reviews	looks real nice. __________________ Wayne

08-22-2009, 04:23 PM	#5
Ali 556 Zilvia Junkie Join Date: Sep 2006 Location: Far Far Away...... Posts: 359 Trader Rating: (0) Feedback Score: 0 reviews	good review, but i think it's a Little close to the bumber and the stock bumber might melt from the heat btw how much $$$? __________________ '95 S14 Se With HKS's - BREMBO's - ES/SPL.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

05-12-2009, 12:52 AM	#2
grnappletree14 BANNED Join Date: Aug 2006 Location: SOCAL/chino hills (909) Posts: 1,829 Trader Rating: (6) Feedback Score: 6 reviews	good review !!!!!!!!!!!

08-22-2009, 01:26 PM	#4
carps13guy Leaky Injector Join Date: Aug 2008 Location: santa barbara Age: 34 Posts: 54 Trader Rating: (3) Feedback Score: 3 reviews	hey man, do you have any sound clips? im thinking of getting one for my s13

08-23-2009, 05:44 AM	#6
bshotts Zilvia Junkie Join Date: Jan 2003 Location: Indianapolis, IN Age: 38 Posts: 472 Trader Rating: (13) Feedback Score: 13 reviews	I've got a sound clip for ya....well except for the fact that I can't get the 3gp format to upload correctly. Tell you what, give me an email addy and I won't hesistate to get it to you. Price for this particular exhaust was a (stainless) steal in my opinion (pun intended); roughly 300 shipped from Enjuku.

01-22-2011, 08:27 PM	#8
Blacksilvy Leaky Injector Join Date: Apr 2008 Location: Louisville, KY Age: 34 Posts: 61 Trader Rating: (1) Feedback Score: 1 reviews	i hate to revive an old thread but is this exhaust no longer available now?