SR20DET falls on its face @ 5.5K rpms - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

*StryfeS13* · 07-19-2011, 08:41 PM

I've been working on my friends SR20 and I can't figure out why it's doing this. It's almost like it hits fuel cut, or a rev limiter, and just completely stops building boost, accelerating, etc.

There are no boost leaks, AFR's are good, etc.

His set up is:

S15 T28 Turbo at stock boost
Apex'i AVCR
Sard 550cc injectors
Z32 MAF

I have checked timing,ignition timing, i've tried turning the AVCR to "off," I've checked plug gaps, etc. I've tried all I can think of.

Also tried to completely remove the AVCR from the picture, by unplugging it, and routing the wastegate straight to the hotpipe, instead of the boost controller. Same issue.

Any thoughts?

sebastianwrx · 07-19-2011, 09:23 PM

.............

Sileighty_85 · 07-19-2011, 09:42 PM

What are the plugs gapped to?

thizzen4 · 07-19-2011, 10:00 PM

CHECK UR TPS SENSOR next to throttle body might have a dead spot in it holddd it all the way down with a screw driver and have some one rev and see if its thatt

sebastianwrx · 07-19-2011, 10:12 PM

Quote:

Originally Posted by Sileighty_85

What are the plugs gapped to?

0.28 and tps was fine we checked

bc. · 07-19-2011, 10:20 PM

fuel pump checked yet?

edit: what is the fuel pump?

sebastianwrx · 07-19-2011, 10:45 PM

Quote:

Originally Posted by bc.

fuel pump checked yet?

edit: what is the fuel pump?

walbro 255

chininsan · 07-19-2011, 10:54 PM

do you have the stock rubber intake piping?
check that. sometimes the spring inside of it screws up.

codyace · 07-19-2011, 11:07 PM

boost leak

*StryfeS13* · 07-19-2011, 11:28 PM

Quote:

Originally Posted by chininsan

do you have the stock rubber intake piping?
check that. sometimes the spring inside of it screws up.

Yes, it has stock rubber intake piping.

How can the spring cause it to do this?

Quote:

Originally Posted by codyace

boost leak

We've checked all couplers, even made a boost leak tester...there is no boost leak. However, the Greddy RS bov has a little hole on the back of it (factory), and it leaks during the boost leak test, why is this?

sebastianwrx · 07-20-2011, 12:50 AM

hi just checked my buddy car and lil update when the car was cold it goes the boost no problems and no fuel cut ...so what could be it ?..bad fuel pump or coil?

codyace · 07-20-2011, 07:58 AM

Quote:

Originally Posted by StryfeS13

We've checked all couplers, even made a boost leak tester...there is no boost leak. However, the Greddy RS bov has a little hole on the back of it (factory), and it leaks during the boost leak test, why is this?

That part is ok, it's just a little vent to aide in the operation of the blow off valve -- it leaking doesn't effect how the car runs.

WHen this condition occurs, can you go WOT and the car continues to run, albiet off the 'limiter' sort to speak.

NismoR003 · 07-20-2011, 08:02 AM

what do you mean it stops building boost?
does it maintain boost or it falls back to 0?

can you be more specific?

*StryfeS13* · 07-20-2011, 02:25 PM

Quote:

Originally Posted by codyace

That part is ok, it's just a little vent to aide in the operation of the blow off valve -- it leaking doesn't effect how the car runs.

WHen this condition occurs, can you go WOT and the car continues to run, albiet off the 'limiter' sort to speak.

Oh, alright.

When it happens, yes the car continues to run, it doesnt turn off or sputter or anything. It just hits a wall. When the car is cold, it does not do this. I'm thinking maybe fuel pump....or coil harness?

Quote:

Originally Posted by NismoR003

what do you mean it stops building boost?
does it maintain boost or it falls back to 0?

can you be more specific?

The car hits a wall and does nothing...that's as specific as it can be explained haha.

codyace · 07-20-2011, 02:52 PM

To check the coil pack harness you could check resistance and readings via Multimeter and FSM, I'd do that as if it checks out you can rule that out.

Member Jspaeth on here had an issue like this and his ultimately was solved by back probing the ECU pins and making sure they were making contact. I had a similar issue to this and it was a loose coupler, that had escaped my initial inspection of all couplers.

Aside from that, use the FSM to troubleshoot your main sensors....TPS, CAS, CTS, MAF and O2. It doesn't take long to check signal wire integrity.

JDMRIDDAZ · 07-21-2011, 10:01 PM

u should rewire ur fuel pump
with heavy duty wire and relay
definatly check ohms on coils
also check the two plugs that power engine harness
to see if all wires r getting full 12v...
also is the engine like gurgling at 5.5 k ?
or cutting off?
also do u have a tuned ecu ?
if so try a stock one and see wat happens

Sil-Eighty SE-K · 07-21-2011, 10:11 PM

i say pump.... throw in a gauge and see hwat it reads at WOT when it happens

sebastianwrx · 07-21-2011, 11:28 PM

Coil harness checked theyre reading 12.5 in all 4...

sebastianwrx · 07-22-2011, 12:11 AM

Quote:

Originally Posted by JDMRIDDAZ

u should rewire ur fuel pump
with heavy duty wire and relay
definatly check ohms on coils
also check the two plugs that power engine harness
to see if all wires r getting full 12v...
also is the engine like gurgling at 5.5 k ?
or cutting off?
also do u have a tuned ecu ?
if so try a stock one and see wat happens

hi i was at my buddy car earlier and checked the ohm in coil harness,tps,injectors,...tps was fine ,injectors at .14, coil harness all of them are 12.5 and when u go half throttle it goes fine and pass without fuel cut except when its full throttle than it gets fuel cut exactly at 5000 sometime 5200..could it be fuel pump getting bad?

codyace · 07-22-2011, 08:01 AM

I knwo plug gaps were checked, but what are they set at?

sebastianwrx · 07-22-2011, 08:26 AM

They were gap at .28

JDMRIDDAZ · 07-22-2011, 10:43 PM

also i meant the ohms on the coil packs not just the 12v source they have to be 1k ohms
put a stock ecu on it and see if it happens again

codyace · 07-23-2011, 10:42 AM

Quote:

Originally Posted by codyace

I knwo plug gaps were checked, but what are they set at?

Try gapping them down to .022 and see if that fixes it up. It may be spark blow out. With the age of these components getting older and olrder, it's hard to say how capable a 20 year coil pack is anymore.

KendallH · 07-23-2011, 10:54 AM

I'd bet 5 dollhair its the knock sensor

codyace · 07-23-2011, 11:23 AM

Quote:

Originally Posted by KendallH

I'd bet 5 dollhair its the knock sensor

Knock sensor shouldn't even be working at that point, it's sub 4000 IIRC

*StryfeS13* · 07-23-2011, 03:53 PM

Alright guys.

- I checked ECU codes, there is no knock sensor code. I built the motor and the knock sensor is good, and the wiring to the knock sensor is good.

- Today I gapped the plugs from .028 to .025, and it's the same deal.

- I tried retarding and advancing the timing, like 20 different times. Was never any better or worse, it made no difference.

- I swapped my walbro fp into it, which I know is good because it powered my KA-T just fine, problem still persists.

At this point, I'm thinking it may possibly be the coil packs themselves being bad?

Kinda lost.

codyace · 07-23-2011, 04:22 PM

Is there anyway you can get a video of it when it happens?

*StryfeS13* · 07-23-2011, 04:32 PM

Yeah I can try next time I see the car.

91s13shawn · 07-23-2011, 04:33 PM

My car is having the same exact problem! it cuts out/ hits a wall at 5000ish but when the car is cold it runs great. Please let me know if you find what the problem is i have been stumped for months.

*StryfeS13* · 07-23-2011, 04:36 PM

Do you have an AVCR, Shawn?

I hope you say no, so I can rule that out as a problem lol.

07-19-2011, 08:41 PM	#1
StryfeS13 It's Always Broken. Join Date: Feb 2010 Location: Fresno, CA Posts: 1,363 Trader Rating: (14) Feedback Score: 14 reviews	SR20DET falls on its face @ 5.5K rpms I've been working on my friends SR20 and I can't figure out why it's doing this. It's almost like it hits fuel cut, or a rev limiter, and just completely stops building boost, accelerating, etc. There are no boost leaks, AFR's are good, etc. His set up is: S15 T28 Turbo at stock boost Apex'i AVCR Sard 550cc injectors Z32 MAF I have checked timing,ignition timing, i've tried turning the AVCR to "off," I've checked plug gaps, etc. I've tried all I can think of. Also tried to completely remove the AVCR from the picture, by unplugging it, and routing the wastegate straight to the hotpipe, instead of the boost controller. Same issue. Any thoughts?

07-19-2011, 09:42 PM	#3
Sileighty_85 Post Whore! Join Date: Dec 2006 Location: Misawa, Japan Posts: 6,815 Trader Rating: (8) Feedback Score: 8 reviews	What are the plugs gapped to? __________________ 後輪駆動車１番 1989 Built SR GT2871R -363whp 1998 S14 W/RB25- 250ish (For Now) 1986 SR86 - 200ish 1990 R32 GTR - 320hp Don't Buy Engines from JDM-Online http://zilvia.net/f/businesses/207457-jdm-online.html Don't Buy XS-Power or SSAC Shit

07-19-2011, 10:20 PM	#6
bc. Zilvia Addict Join Date: Aug 2010 Location: St. Louis Posts: 868 Trader Rating: (0) Feedback Score: 0 reviews	fuel pump checked yet? edit: what is the fuel pump? __________________ * S14SR22 * 9.0 c/r * GT3071R *

07-19-2011, 11:07 PM	#9
codyace Post Whore! Join Date: Dec 2004 Location: Poconos, PA Age: 36 Posts: 8,030 Trader Rating: (58) Feedback Score: 58 reviews	boost leak __________________ *Want Air Conditioning in your SR20 Swapped car? Check out www.sr20acbrackets.com for more information! Quest Alternator Conversions for SR20!* Check my Group Buy! Tired of lousy internal gates? Go external wastegate with one of my manifolds, Check out my group buy

07-20-2011, 02:52 PM	#15
codyace Post Whore! Join Date: Dec 2004 Location: Poconos, PA Age: 36 Posts: 8,030 Trader Rating: (58) Feedback Score: 58 reviews	To check the coil pack harness you could check resistance and readings via Multimeter and FSM, I'd do that as if it checks out you can rule that out. Member Jspaeth on here had an issue like this and his ultimately was solved by back probing the ECU pins and making sure they were making contact. I had a similar issue to this and it was a loose coupler, that had escaped my initial inspection of all couplers. Aside from that, use the FSM to troubleshoot your main sensors....TPS, CAS, CTS, MAF and O2. It doesn't take long to check signal wire integrity. __________________ *Want Air Conditioning in your SR20 Swapped car? Check out www.sr20acbrackets.com for more information! Quest Alternator Conversions for SR20!* Check my Group Buy! Tired of lousy internal gates? Go external wastegate with one of my manifolds, Check out my group buy

07-19-2011, 09:23 PM	#2
sebastianwrx Zilvia Junkie Join Date: Oct 2009 Location: fresno,CA Age: 35 Posts: 493 Trader Rating: (18) Feedback Score: 18 reviews	.............

07-19-2011, 10:00 PM	#4
thizzen4 Zilvia FREAK! Join Date: May 2011 Location: tacoma 253 Age: 30 Posts: 1,169 Trader Rating: (22) Feedback Score: 22 reviews	CHECK UR TPS SENSOR next to throttle body might have a dead spot in it holddd it all the way down with a screw driver and have some one rev and see if its thatt

07-19-2011, 10:54 PM	#8
chininsan Join Date: May 2008 Location: Okinawa Posts: 5 Trader Rating: (0) Feedback Score: 0 reviews	do you have the stock rubber intake piping? check that. sometimes the spring inside of it screws up.

07-20-2011, 12:50 AM	#11
sebastianwrx Zilvia Junkie Join Date: Oct 2009 Location: fresno,CA Age: 35 Posts: 493 Trader Rating: (18) Feedback Score: 18 reviews	hi just checked my buddy car and lil update when the car was cold it goes the boost no problems and no fuel cut ...so what could be it ?..bad fuel pump or coil?

07-20-2011, 08:02 AM	#13
NismoR003 Leaky Injector Join Date: Aug 2009 Location: fort bragg, nc Age: 33 Posts: 84 Trader Rating: (0) Feedback Score: 0 reviews	what do you mean it stops building boost? does it maintain boost or it falls back to 0? can you be more specific?

07-21-2011, 10:01 PM	#16
JDMRIDDAZ Zilvia Junkie Join Date: Sep 2007 Location: ｆォリダ Age: 44 Posts: 440 Trader Rating: (3) Feedback Score: 3 reviews	u should rewire ur fuel pump with heavy duty wire and relay definatly check ohms on coils also check the two plugs that power engine harness to see if all wires r getting full 12v... also is the engine like gurgling at 5.5 k ? or cutting off? also do u have a tuned ecu ? if so try a stock one and see wat happens __________________ シチサｎ w/ka20det:in progress シチサｎw/sr20det:stolen

07-21-2011, 11:28 PM	#18
sebastianwrx Zilvia Junkie Join Date: Oct 2009 Location: fresno,CA Age: 35 Posts: 493 Trader Rating: (18) Feedback Score: 18 reviews	Coil harness checked theyre reading 12.5 in all 4...

07-22-2011, 08:01 AM	#20
codyace Post Whore! Join Date: Dec 2004 Location: Poconos, PA Age: 36 Posts: 8,030 Trader Rating: (58) Feedback Score: 58 reviews	I knwo plug gaps were checked, but what are they set at? __________________ *Want Air Conditioning in your SR20 Swapped car? Check out www.sr20acbrackets.com for more information! Quest Alternator Conversions for SR20!* Check my Group Buy! Tired of lousy internal gates? Go external wastegate with one of my manifolds, Check out my group buy

07-22-2011, 08:26 AM	#21
sebastianwrx Zilvia Junkie Join Date: Oct 2009 Location: fresno,CA Age: 35 Posts: 493 Trader Rating: (18) Feedback Score: 18 reviews	They were gap at .28

07-22-2011, 10:43 PM	#22
JDMRIDDAZ Zilvia Junkie Join Date: Sep 2007 Location: ｆォリダ Age: 44 Posts: 440 Trader Rating: (3) Feedback Score: 3 reviews	also i meant the ohms on the coil packs not just the 12v source they have to be 1k ohms put a stock ecu on it and see if it happens again __________________ シチサｎ w/ka20det:in progress シチサｎw/sr20det:stolen

07-23-2011, 10:54 AM	#24
KendallH Zilvia Addict Join Date: Jan 2011 Location: Clearwater, FL Level: Master Troll Age: 29 Posts: 871 Trader Rating: (3) Feedback Score: 3 reviews	I'd bet 5 dollhair its the knock sensor

07-23-2011, 03:53 PM	#26
StryfeS13 It's Always Broken. Join Date: Feb 2010 Location: Fresno, CA Posts: 1,363 Trader Rating: (14) Feedback Score: 14 reviews	Alright guys. - I checked ECU codes, there is no knock sensor code. I built the motor and the knock sensor is good, and the wiring to the knock sensor is good. - Today I gapped the plugs from .028 to .025, and it's the same deal. - I tried retarding and advancing the timing, like 20 different times. Was never any better or worse, it made no difference. - I swapped my walbro fp into it, which I know is good because it powered my KA-T just fine, problem still persists. At this point, I'm thinking it may possibly be the coil packs themselves being bad? Kinda lost.

07-23-2011, 04:22 PM	#27
codyace Post Whore! Join Date: Dec 2004 Location: Poconos, PA Age: 36 Posts: 8,030 Trader Rating: (58) Feedback Score: 58 reviews	Is there anyway you can get a video of it when it happens? __________________ *Want Air Conditioning in your SR20 Swapped car? Check out www.sr20acbrackets.com for more information! Quest Alternator Conversions for SR20!* Check my Group Buy! Tired of lousy internal gates? Go external wastegate with one of my manifolds, Check out my group buy

07-23-2011, 04:32 PM	#28
StryfeS13 It's Always Broken. Join Date: Feb 2010 Location: Fresno, CA Posts: 1,363 Trader Rating: (14) Feedback Score: 14 reviews	Yeah I can try next time I see the car.

07-23-2011, 04:33 PM	#29
91s13shawn Join Date: Mar 2010 Location: Bradenton, FL Age: 30 Posts: 19 Trader Rating: (0) Feedback Score: 0 reviews	My car is having the same exact problem! it cuts out/ hits a wall at 5000ish but when the car is cold it runs great. Please let me know if you find what the problem is i have been stumped for months.

07-23-2011, 04:36 PM	#30
StryfeS13 It's Always Broken. Join Date: Feb 2010 Location: Fresno, CA Posts: 1,363 Trader Rating: (14) Feedback Score: 14 reviews	Do you have an AVCR, Shawn? I hope you say no, so I can rule that out as a problem lol.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode