GUNMETALV35

I was planning on going the SR22VET route but finally accepted that I just don't have the time for this build. So, I'm selling off what I've gathered so far.

Here it goes:

HKS GT2835
52 Trim 0.64 A/R 71.1mm compressor wheel, 84 Trim 56.5mm turbine wheel. Equivalent to a GT3071R in a T25/T28 configuration with ported housings by HKS. The GT2835/3071R turbos use better flowing T04E housings vs. the T04B ones used on the GT28RS/GT2871R.



- $650 OBO

SR20DET built short block.




Bought from FLIP, one of the mods on 240Atlanta. He had everything machined by Grimes Automotive Machining Inc. Everything was spec'd out to handle 600hp reliably.

Eagle Rods
Counterbalanced Crank
All bearings in perfect condition. I don't remember who made them.
*No pistons (planned on buying JE pistons with valve reliefs but didn't)

-$700 OBO

P12 20v SR20VE cylinder head







Dual valve springs w/ seats
No valve cover
No cams (P12 cams on order; will post later)

-$1000 OBO

Billet aluminum VVL remote placement solenoid brackets


-$80

P12 20v custom intake runner section w/ GReddy fuel rail and 80MM TB






Upper plenum chamber needs to be finished. Will include some finishing material.
-$700 OBO

Mazworx head and main studs



-$225 OBO

Z33 to SR conversion setup






SOLD



R200 Diff(on the right)

It was said to be welded but I never confirmed so... $100

Whiteline Strut Tower Brace

-$100 OBO

Fidanza Aluminum Lightweight Flywheel

*Absolutely NEEDS replacement friction surface plate (goes for $60)
-$100 OBO

Oil Temp Gauge

-$20

Walbro 255lph Fuel Pump Kit

-SOLD

Front & Rear Main Seals/ gasket

-$30 OBO

I still have a few things in the garage. I'll post them up later.

All items DO NOT include shipping. All reasonable offers will be considered. Lowballers will be ignored.

email me at: [email protected]ail.com
Text me at: 919-628-6765 Text only please.

*TRADES- MAY BE interested in 350z/G35 coupe suspension parts. Really nice, low offset wheels... or anything else G35 related. Just putting it out there.

__________________

adicarlo

Did you have to mod the trans at all?

Sent from my SAMSUNG-SGH-I747 using Tapatalk 2

JFoxx

would you ship the trans? and would you sell it without the diff/speed sensor?

GUNMETALV35

The bellhousing was machined to fit an SR. The shifter bracket and linkage mod was done to fit in stock S13 location. All new seals and clips were put in after teardown.

__________________

GUNMETALV35

I don't mind shipping anything. For the bigger items, asking price + shipping + PP fees etc. can be negotiated.

I can take off the diff/ speed sensor. I wouldn't really want to split up anything else from the setup though.

__________________

JFoxx

could you do $1500 shipped without diff/sensor or $1200 shipped without diff/sensor and driveshaft?

Nismo11

Free bump for viewing, glws.

GUNMETALV35

Sorry for the late reply. I was away from a computer most of this week.

Text me an address so I can check out shipping. If you can find a commercial address, I think that'd be the way to go.

__________________

GUNMETALV35

JWT adjustable cam gears

- $85 OBO

HKS triple plate clutch


Used condition but has new clutch discs.
- $900 OBO

I don't want to hoard these parts anymore since I have no desire to use them. Best offer takes them. I'm just putting a price because a price needs to be set. Throw some offers. Worst I'll say is no.

__________________

sm kid

Thanks for the walbro pump

Bump for u sir

JFoxx

will you part the adapter plate and hardware?

GUNMETALV35

I kinda want to keep the kit together as much as possible. I'm getting lots of interest but no one has pulled the trigger yet.

At the same time, I don't want to say no all together because I'd rather just move this stuff out.

So I guess it's maybe. If no one snatches it all together soon, then yes.

__________________

GUNMETALV35

Bump... Lowered prices....

Get this stuff out of my garage!

__________________

bussitcustoms

Trade the whole z trans setup for some AME Shallen CX's? 18x9.5 -12 fronts, 18x10 -16 rear. 5x114.3, 6" lips.

GUNMETALV35

Damn.... sweet wheels bro. Unfortunately, the whole trans setup was just recently sold.

__________________

GUNMETALV35

Payday weekend bump! C'mon guys, help me get my Tundra lifted!

__________________

ike182000

Thanks for the great parts bump

GUNMETALV35

New fiscal year bump?

__________________

Lueee10

power steering pump?

lewisfk

cam gears i need them Jim Wolf, $70

enkei2k

2 bump limit. you can start a new thread in 3 days

__________________
Ask enkei2k

xquizitditz