Need s14 SR20 crank pulley ASAP. Help!!! - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

uaserge · 08-18-2012, 10:29 AM

Please help with any knowledge. I need a crank pulley asap for my s14 sr20. My stock just shifted forward I am guessing it’s done. Where can I buy it and hopefully not to expensive.

*fliprayzin240sx* · 08-18-2012, 11:01 AM

Look around and see if somebody's parting out an SR. IIRC, the crank pulleys are all the same between RWD SR20s. Might even be the same as FWD.

uaserge · 08-18-2012, 11:10 AM

Should i just try going with oem?

*fliprayzin240sx* · 08-18-2012, 01:56 PM

OEM is more than good enough...unless you're making a 600hp engine, there's really no for an aftermarket crank pulley.

But if you insist on an aftermarket one...
ATI Super Damper (Main Pulley) - SR20

cj1977 · 08-19-2012, 06:52 PM

sr20det crank pulley | eBay

uaserge · 08-20-2012, 07:44 AM

Thanks. I ordered oem crank pulley but does anyone has an easy way to replace it. I tried searching on here for how to replace it but could not find anything. Thanks

Sent from my MB855 using Tapatalk 2

godsmack · 08-20-2012, 04:52 PM

get a pulley puller and you're more that likely going to need to pull out the radiator in order to fit the puller in there. you might be able to get it off by hand but it's at a pita spot to get to by hand so you can try it and get a puller later if unsuccessful.

uaserge · 08-20-2012, 05:09 PM

Okay cool i will try thanks

Sent from my MB855 using Tapatalk 2

crescendo · 10-10-2012, 04:43 PM

I had success pulling my pulley off w/a 3 claw puller. It fit without removing the radiator. Remove the fan clutch (if installed) along w/the accessory belts. Back the crank pulley bolt out an inch or so, but don't remove it all the way. This gives the claw puller a center to push against (the crank pulley bolt has a dimple in the center and makes this easier).

08-18-2012, 10:29 AM	#1
uaserge Join Date: Aug 2011 Location: Barksdale AFB Age: 33 Posts: 36 Trader Rating: (1) Feedback Score: 1 reviews	Need s14 SR20 crank pulley ASAP. Help!!! Please help with any knowledge. I need a crank pulley asap for my s14 sr20. My stock just shifted forward I am guessing it’s done. Where can I buy it and hopefully not to expensive.

08-18-2012, 11:01 AM	#2
fliprayzin240sx Man w/ CTSV & a Car Seat Join Date: Aug 2002 Location: Tampa Posts: 17,998 Trader Rating: (19) Rides Gallery: fliprayzin240sx Feedback Score: 19 reviews	Look around and see if somebody's parting out an SR. IIRC, the crank pulleys are all the same between RWD SR20s. Might even be the same as FWD. __________________ If you think Zilvia has too many assholes... CLICK HERE!!!

08-18-2012, 01:56 PM	#4
fliprayzin240sx Man w/ CTSV & a Car Seat Join Date: Aug 2002 Location: Tampa Posts: 17,998 Trader Rating: (19) Rides Gallery: fliprayzin240sx Feedback Score: 19 reviews	OEM is more than good enough...unless you're making a 600hp engine, there's really no for an aftermarket crank pulley. But if you insist on an aftermarket one... ATI Super Damper (Main Pulley) - SR20 __________________ If you think Zilvia has too many assholes... CLICK HERE!!!

10-10-2012, 04:43 PM	#9
crescendo Leaky Injector Join Date: Sep 2006 Location: S-A-C Posts: 142 Trader Rating: (0) Feedback Score: 0 reviews	I had success pulling my pulley off w/a 3 claw puller. It fit without removing the radiator. Remove the fan clutch (if installed) along w/the accessory belts. Back the crank pulley bolt out an inch or so, but don't remove it all the way. This gives the claw puller a center to push against (the crank pulley bolt has a dimple in the center and makes this easier). __________________ FREE DNB & DUBSTEP MIXES

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

08-18-2012, 11:10 AM	#3
uaserge Join Date: Aug 2011 Location: Barksdale AFB Age: 33 Posts: 36 Trader Rating: (1) Feedback Score: 1 reviews	Should i just try going with oem?

08-19-2012, 06:52 PM	#5
cj1977 Join Date: Aug 2012 Location: TX Posts: 38 Trader Rating: (0) Feedback Score: 0 reviews	sr20det crank pulley \| eBay

08-20-2012, 07:44 AM	#6
uaserge Join Date: Aug 2011 Location: Barksdale AFB Age: 33 Posts: 36 Trader Rating: (1) Feedback Score: 1 reviews	Thanks. I ordered oem crank pulley but does anyone has an easy way to replace it. I tried searching on here for how to replace it but could not find anything. Thanks Sent from my MB855 using Tapatalk 2

08-20-2012, 04:52 PM	#7
godsmack Zilvia Addict Join Date: Feb 2009 Location: Allentown, PA Age: 36 Posts: 652 Trader Rating: (0) Feedback Score: 0 reviews	get a pulley puller and you're more that likely going to need to pull out the radiator in order to fit the puller in there. you might be able to get it off by hand but it's at a pita spot to get to by hand so you can try it and get a puller later if unsuccessful.

08-20-2012, 05:09 PM	#8
uaserge Join Date: Aug 2011 Location: Barksdale AFB Age: 33 Posts: 36 Trader Rating: (1) Feedback Score: 1 reviews	Okay cool i will try thanks Sent from my MB855 using Tapatalk 2