coilover spring gets caught (pix) - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

flclsteve · 03-31-2008, 08:34 PM

So the top part of the spring gets caught i just pulled the spring out a bit and it popped back in place. I wanna know what to do to prevent this from happening was not driving it too hard maby due to a bumpy surface tho.

adrians_s13 · 03-31-2008, 08:47 PM

is it popping out when its sitting or just when you lift it up?

usdm180sx · 03-31-2008, 08:48 PM

try tightening up the preload adjustment. if it doesn't have preload adjustment then you'll have to raise the car?

benjim · 03-31-2008, 08:49 PM

You are either going to need to give the spring more pre-load or purchase helper/asist springs to provide the pre-load when the suspenion unloads.

ScarredOne · 04-01-2008, 01:17 PM

Yeah, you need something like this:

http://more-japan.com/product.php?pr...6&cat=0&page=1

when your suspension unloads, helper springs will keep your coilover springs seated in the upper spring perches, yet will compress under the weight of the car when it's level. You should get another perch to fit in between the helper and main spring though.

Silvia_S13 · 04-01-2008, 01:21 PM

do what everyone else suggested, or buy legit suspension.

flclsteve · 04-01-2008, 02:20 PM

very cool thanks alot im glad helper springs are not too expensive but ill be sure to get some next pay check.

***dorkidori_s13*** · 04-01-2008, 05:47 PM

dont bother with the helper spring...your springs preload is off

jack your car up...take the wheel off...tighten your dampers lower perches up til the spring is FIRMLY against the top mount...tighten your BOTTOM PERCH (not the one directly below the spring) using a screw driver and hammer...tap it into place until snug...put the wheel back on and you should be good to go

Jung918 · 04-01-2008, 09:10 PM

what are the name of those coilovers?

aznpoopy · 04-01-2008, 09:17 PM

either of the suggested solutions will fix your issue.

however, by raising the bottom collar until the spring is captive you will be raising the car.

if you don't want to do that and your coilovers are single height adjustable, you must use helper springs.

if they are dual you can reset height with the adjustable shock body.

whatever you do, don't forget to get an alignment afterwards.

flclsteve · 04-01-2008, 11:17 PM

There actually JIC's some of there older ones

03-31-2008, 08:34 PM	#1
flclsteve Zilvia Junkie Join Date: Aug 2007 Location: Irvine Age: 32 Posts: 538 Trader Rating: (2) Feedback Score: 2 reviews	coilover spring gets caught (pix) So the top part of the spring gets caught i just pulled the spring out a bit and it popped back in place. I wanna know what to do to prevent this from happening was not driving it too hard maby due to a bumpy surface tho. __________________

03-31-2008, 08:47 PM	#2
adrians_s13 Post Whore! Join Date: Jul 2005 Location: long beach, CA ^_^ Age: 36 Posts: 2,877 Trader Rating: (29) Feedback Score: 29 reviews	is it popping out when its sitting or just when you lift it up? __________________ @adrianfromthecastle

03-31-2008, 08:48 PM	#3
usdm180sx Post Whore! Join Date: Dec 2005 Location: 562 Posts: 4,807 Trader Rating: (5) Rides Gallery: usdm180sx Feedback Score: 5 reviews	try tightening up the preload adjustment. if it doesn't have preload adjustment then you'll have to raise the car? __________________ -Norm!

04-01-2008, 01:21 PM	#6
Silvia_S13 Zilvia Junkie Join Date: Jul 2005 Location: SD Age: 35 Posts: 331 Trader Rating: (0) Feedback Score: 0 reviews	do what everyone else suggested, or buy legit suspension. __________________ sddrift.com - smirkis - poweredbymax.net

04-01-2008, 02:20 PM	#7
flclsteve Zilvia Junkie Join Date: Aug 2007 Location: Irvine Age: 32 Posts: 538 Trader Rating: (2) Feedback Score: 2 reviews	very cool thanks alot im glad helper springs are not too expensive but ill be sure to get some next pay check. __________________

03-31-2008, 08:49 PM	#4
benjim Join Date: Sep 2007 Location: SLC, Utah Age: 41 Posts: 43 Trader Rating: (0) Feedback Score: 0 reviews	You are either going to need to give the spring more pre-load or purchase helper/asist springs to provide the pre-load when the suspenion unloads.

04-01-2008, 01:17 PM	#5
ScarredOne Join Date: Jul 2005 Location: LA Posts: 49 Trader Rating: (0) Feedback Score: 0 reviews	Yeah, you need something like this: http://more-japan.com/product.php?pr...6&cat=0&page=1 when your suspension unloads, helper springs will keep your coilover springs seated in the upper spring perches, yet will compress under the weight of the car when it's level. You should get another perch to fit in between the helper and main spring though.

04-01-2008, 05:47 PM	#8
*dorkidori_s13* ITS LISA'S FAULT!!! Join Date: Jun 2003 Location: Las Vegas Age: 39 Posts: 7,332 Trader Rating: (41) Feedback Score: 41 reviews	dont bother with the helper spring...your springs preload is off jack your car up...take the wheel off...tighten your dampers lower perches up til the spring is FIRMLY against the top mount...tighten your BOTTOM PERCH (not the one directly below the spring) using a screw driver and hammer...tap it into place until snug...put the wheel back on and you should be good to go __________________ Bought something from me??? POST A REVIEW HERE!!!

04-01-2008, 09:10 PM	#9
Jung918 Post Whore! Join Date: Oct 2003 Location: CA Posts: 3,203 Trader Rating: (2) Feedback Score: 2 reviews	what are the name of those coilovers? __________________ Sale: Hello Kitty Horn Button S14 Rear Valences K.Y. Gordon the Thief (Tony Chen)

04-01-2008, 09:17 PM	#10
aznpoopy Post Whore! Join Date: Mar 2003 Location: New Jersey Age: 40 Posts: 5,013 Trader Rating: (1) Feedback Score: 1 reviews	either of the suggested solutions will fix your issue. however, by raising the bottom collar until the spring is captive you will be raising the car. if you don't want to do that and your coilovers are single height adjustable, you must use helper springs. if they are dual you can reset height with the adjustable shock body. whatever you do, don't forget to get an alignment afterwards.

04-01-2008, 11:17 PM	#11
flclsteve Zilvia Junkie Join Date: Aug 2007 Location: Irvine Age: 32 Posts: 538 Trader Rating: (2) Feedback Score: 2 reviews	There actually JIC's some of there older ones __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode