Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > Specific Topics > Archive and FAQs

Archive and FAQs Archives and Frequently Asked Questions about the 240SX are in here.


 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 08-05-2007, 09:13 PM   #1
LB.Motoring
Post Whore!
 
LB.Motoring's Avatar
 
Join Date: Jul 2006
Location: SòCal♥
Age: 35
Posts: 5,840
Trader Rating: (1)
LB.Motoring is close to perfectionLB.Motoring is close to perfectionLB.Motoring is close to perfectionLB.Motoring is close to perfectionLB.Motoring is close to perfectionLB.Motoring is close to perfectionLB.Motoring is close to perfectionLB.Motoring is close to perfectionLB.Motoring is close to perfectionLB.Motoring is close to perfectionLB.Motoring is close to perfection
Feedback Score: 1 reviews
Send a message via AIM to LB.Motoring
s13 S13 Hatch Rear Overfenders DIY *Approved*

So you think your cool, and you want over fenders, or you might want to cover up some rough spots, or you think you have large rear wheels, either way, your new, and you have no idea what your doing.

This is where Dr. Robby comes in.

What you will need.


-Balls
-Sawsall
-Overfenders
-Grinder
-Welder
-Snap Clamps
-Rivet Gun
-5/16's Rivets
-Drill
-5/16's Metal Drill Bit
-Large Hammer

1. Take Aim at your quater panal, Size it up with your overfender, see exactly where it will go, see how far you can cut, This varies between companies. I went with a B-Magic rear 30mm, and they fit Great.




2. Start cutting. Now you know how high you can cut, basically all the way to the top of the wheel well. WHY NOT? your covering it. Remember my car was a little battle damaged. So anyways cutting for me wasn't so hurtful. Remember to put your balls on. Take the saws-all and start cutting a new well. Note your metal will start to separate.



3. KEEP cutting, don't be a pussy. Cut, and hammer it up till the lips come together, then use your welder and very low, to tack them back together, you will need clamps to hold them together as you weld them.



4. Once your done welding, wipe it all down, and hit it with some primer, this will keep that bare metal from rusting.

5. Place the overfender back on, Use Duct tape to hold it in place. Remember THIS cannot move whatsoever. So tape it up good.



6. Now that is securely on there, You can take the dimples on the overfender and drill them for the rivets. I would suggest do them one at a time. Drill them all the way through the body and fender at the same time. Then place the rivet in and pop them in.




7. Now fill those wheel wells up.

I did a 5 lug and 17x9 +0 on stock camber ~ -3






My car went from totaled, to totally cool.








To:




__________________
Robby Leuer
LB.Motoring is offline  
Sponsored Links
 

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 07:56 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™