Swapping out bad crankshaft Ka24de - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

alohallaround · 03-18-2019, 08:06 PM

Hey guys, quick noob question. I picked up an s14 Zenki that hasn’t ran in 2 years, got the car to start and it had a bad rod knock. I pull off the oil pan and the rod bearings are done on cylinders 1-3 so much that the crank has some damage. The rods look fine so my question is can I just pick up a good crank and throw it in with alll new bearings? Any help is appreciated

***S14DB*** · 03-18-2019, 09:11 PM

You are going to need to micrometer the bore of the mains and rods to make sure they aren’t out of round. The the replacement crank to determine bearings size.

alohallaround · 03-18-2019, 10:36 PM

Quote:

Originally Posted by S14DB

You are going to need to micrometer the bore of the mains and rods to make sure they aren’t out of round. The the replacement crank to determine bearings size.

Okay, as far as the block goes, machining isn’t necessary unless the bores are lopsided right? Just make sure I have the correct bearings and I should be good?

jedi03 · 03-19-2019, 07:33 AM

yup! to re-iterate MEASURE so you don't have it happen again...should be pretty easy as you will have the crank markings and the block markings to match what you need pretty easily!

alohallaround · 03-19-2019, 08:20 AM

Quote:

Originally Posted by jedi03

yup! to re-iterate MEASURE so you don't have it happen again...should be pretty easy as you will have the crank markings and the block markings to match what you need pretty easily!

Gotcha! just wanted to make sure I had the right idea. Thanks guys!

*brndck* · 03-19-2019, 08:30 AM

yeahhhhhhhhhh if you had that much metal shaving in the pan theres a good chance it got sucked up into the oil pickup and there are shavings elsewhere in the engine. I wouldn't trust it unless I had replaced the oil pump and cleaned all the oil passages thoroughly.

i'm a big fan of ultrasonic cleaning, but its super convenient that they're only like 3 miles from my house.

alohallaround · 03-19-2019, 09:16 PM

Quote:

Originally Posted by brndck

yeahhhhhhhhhh if you had that much metal shaving in the pan theres a good chance it got sucked up into the oil pickup and there are shavings elsewhere in the engine. I wouldn't trust it unless I had replaced the oil pump and cleaned all the oil passages thoroughly.

i'm a big fan of ultrasonic cleaning, but its super convenient that they're only like 3 miles from my house.

Good point, well I pulled the engine out, might just change the oil pump since it’s out

03-18-2019, 08:06 PM	#1
alohallaround Leaky Injector Join Date: Aug 2011 Location: NorCal Posts: 77 Trader Rating: (6) Feedback Score: 6 reviews	Swapping out bad crankshaft Ka24de Hey guys, quick noob question. I picked up an s14 Zenki that hasn’t ran in 2 years, got the car to start and it had a bad rod knock. I pull off the oil pan and the rod bearings are done on cylinders 1-3 so much that the crank has some damage. The rods look fine so my question is can I just pick up a good crank and throw it in with alll new bearings? Any help is appreciated

03-18-2019, 09:11 PM	#2
*S14DB* AFC #1 Join Date: Oct 2003 Location: 昨晩あなたのお母さんの家 Posts: 20,181 Trader Rating: (3) Feedback Score: 3 reviews	You are going to need to micrometer the bore of the mains and rods to make sure they aren’t out of round. The the replacement crank to determine bearings size. __________________ Comments should be taken as Opinions not as Statements of Fact

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-19-2019, 07:33 AM	#4
jedi03 Nissanaholic! Join Date: Jul 2008 Location: albuquerque Posts: 1,784 Trader Rating: (8) Feedback Score: 8 reviews	yup! to re-iterate MEASURE so you don't have it happen again...should be pretty easy as you will have the crank markings and the block markings to match what you need pretty easily!