HOW TO: 5 Lug Conversion - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

twyztidmind · 10-02-2010, 08:23 PM

After searching i couldn't really find any good detailed 5 lug conversions before doing mine. So i decided to make one! This was done on my S14.

I bought brand new hubs off ebay for 310 shipped. I also bought 5 lug rotors that were drilled and slotted for $115 shipped for all four.

Parts Needed:

5 Lug hubs off SE
5 Lug Rotors off SE
5 Lug Wheels to finish off the setup

Tools Needed:

Impact Gun (If Available)
Socket Set
Ratchets
Flat Head Screw Driver
Hammer
Axle Grease
Axle Sockets 32mm and 36mm
Wrench Set
WD-40
Case of Beer

Ok this is just a guide, I'm not responsible if you mess up your car! This is a medium difficulty project, if you can do an engine swap, you can do this!

Hubs i bought off Ebay

FRONTS:

STEP 1: Remove dust cap, i used a flat head screw driver and a hammer, and hit it like a paint can going around it little by little. (Before i started I went ahead and painted the caliper with high heat paint ~ Half ass job but turned out ok

)

-------------------
STEP 2: Remove axle nut 32MM if i remember right. I just loosened mine until i pulled the caliper off.

-------------------
STEP 3: Remove Caliper and Rotor.

-------------------
STEP 4: Now the hub should just slide right off.

-------------------
STEP 5: Clean shaft and lube it with axle bearing grease.

-------------------
STEP 6: Now you can slide on the new hub, re-torque the axle nut, and install the new rotor and the brake caliper.

-------------------
Thats it for the fronts, now the rears are a little more complicated...

REARS:

STEP 1: Remove Cotter Pin & Axle Nut 36MM. (If you dont have an Impact you can remove center cap of wheel, put it back on the ground and use a break over bar)

-------------------
STEP 2: Remove brake caliper and rotor

-------------------
STEP 3: Remove the 4 bolts on the back side of the hub. You can turn the axle to were the indentions are to get access to each bolt.

-------------------
STEP 4: Remove strut bolt, and the rest of the rear suspension shown in the pic.

-------------------
STEP 5: Now you can pull the hub forward and remove the axle from housing. You can use a mallet to hit the axle to loosen it.

-------------------
STEP 6: With the axle out of the way, you have good access to the hub. I used a sledge hammer (BFH) holding the spindle in my hand and pounded the hub out of the spindle. (This WILL ruin it, i didnt care i was throwing it all away)

-------------------
STEP 7: I used an emery cloth to sand out the spindle hole, mine was rusty.

-------------------
STEP 8: Now put in the new hub, torque down the bolts and reassemble everything in reverse order of which you took it off. You should end up looking like this!

Thats it! Now you have a better selection in wheels. I bought some 350z touring wheels for a great price so thats what im rolling on for now. For $425 i had everything i needed to do the swap and brand spankin new!

ENJOY!

Siberian Husky · 10-02-2010, 08:41 PM

nice CLEAN write up, just the meat n potatoes; i hate when people write DIY's and make them way too long--a way to stroke their ego for writing it up i guess. clean job though.

what bearings did you use? im scared to just use the ebay bearings that come with the hubs. pics of the 350 touring wheels on your s13?

twyztidmind · 10-02-2010, 09:02 PM

Thanks! I used the bearings that came with it, not going to lie, they did look iffy but we dont track this car or anything so i wanted to see how they would hold up as a DD (will keep you guys updated)

No pics of the wheels just yet, getting new tires on them right now, it's an S14 btw..

azndoc · 10-02-2010, 09:13 PM

An easier way to get the rear hubs out is to unbolt the 4 bolts halfway and then use a rubber mallet pounding it out. Doesn't damage anything and comes out really easy.

Good job on the write up

twyztidmind · 10-02-2010, 09:16 PM

Quote:

Originally Posted by azndoc

An easier way to get the rear hubs out is to unbolt the 4 bolts halfway and then use a rubber mallet pounding it out. Doesn't damage anything and comes out really easy.

Good job on the write up

Thanks for that info! I didnt even think of doing that. Mine were rusted pretty bad, i had to pound on it for literally 10 minutes before it came out.

Ares240SX · 10-02-2010, 10:25 PM

10 minutes of pounding with most rubber mallets renders them useless... another idea is to use some penetrating oil, and maybe some heat around the outside edges to free up your old hubs so you don't have to worry about damaging something you might be able to sell to make up for the project costs.

240sxvaj · 10-02-2010, 11:31 PM

pix are good lol!

tqstarburst · 10-02-2010, 11:36 PM

good job man,nice write up,alot of s13 owners are gonna benefit from this

japordie · 10-05-2010, 12:15 PM

nice thread it's short and simple.

*hOngsterr* · 10-05-2010, 01:15 PM

s14 front hubs, arent they held in by a pinch bolt?

if yours just came off then someone messed with your hub before.

but theres another how to somewhere i forgot lol but nice job!

MitchellBade · 10-05-2010, 03:43 PM

Good work on the write up!

Tae-Hyun · 10-05-2010, 03:46 PM

Well i guess you didnt search hard enough.

How to: Install 5 lug hubs (only have pics of rear)

Even though its just the rears, you get the idea.

Nonetheless, your how too is nice with pics for front and rear.

Nice.

twyztidmind · 10-05-2010, 05:32 PM

Quote:

Originally Posted by hOngsterr

s14 front hubs, arent they held in by a pinch bolt?

if yours just came off then someone messed with your hub before.

but theres another how to somewhere i forgot lol but nice job!

Nope, i didnt have any on either side..

Flashman · 10-05-2010, 05:45 PM

i didnt unbolt any of the rear arms when i did my 5 lug

s141996 · 10-06-2010, 02:47 PM

im doing it and I dont have a hub puller and Im doin this right now its a bitch!

kuelee · 10-06-2010, 05:04 PM

Does this also go for s13? And does the front hubs just slide in? No bolts holding the hub?

s141996 · 10-08-2010, 02:39 AM

just got done with mine along with z32 vlsd and z32 front brakes took 2 days and alot of hrs since i didnt have much help, thanks ur write up was my refrence when i couldnt figure something out. /exhausted

Drift_86 · 11-09-2010, 10:22 PM

Awesome thanks! I got the same 5lug off ebay

XxCAPTAINxX · 11-09-2010, 11:00 PM

im curious to know how the ebay hubs hold up. keep us updated please

Krusty_s13 · 11-09-2010, 11:06 PM

Ebay hubs are fine. I rocked them on my previous fastback for about 6 months as a dd and some drift events. No issues with them. Will do it again with my new s13

Drift_86 · 11-09-2010, 11:29 PM

Awesome thanks! I got the same 5lug off ebay

aalbert240 · 11-24-2010, 10:59 PM

Quote:

Originally Posted by kuelee

Does this also go for s13? And does the front hubs just slide in? No bolts holding the hub?

plus 1 on this

s13coupedrfter · 11-24-2010, 11:22 PM

Cant say anything about ebay hubs, never used them.

I have used Ichiba hubs and they are JUNK!!!! I went through 2 front sets of them and each time had a bearing failure within 1 day of daily driving. Yes...they were properly torqued down with a calibrated tq wrench that I use at work. The spindle was in perfict condition. I will never use Ichiba hubs again.

I use OEM s14 hubs without any problems...cant go wrong with factory Nissan stuff. Yes they are more expensive but so is replacing China shit hubs all the time.

Cool write-up, keep up the good work.

xBtony · 11-24-2010, 11:29 PM

awesome write up super helpful. Imma be doing this soon.

iHateMySilvia · 11-24-2010, 11:36 PM

Quote:

Originally Posted by aalbert240

plus 1 on this

slides in

Slammed Assassin · 11-25-2010, 02:27 AM

great writeup!!!

twyztidmind · 11-25-2010, 10:21 AM

For an S13 its about the same if you buy the after market hubs (like the ones i got on ebay). But if you take parts off an S14 SE you will need the whole spindle and LCA for the fronts as well as boring out the strut bolt a little because S14 uses a bigger one iirc.

Hope that helps

Drift_86 · 12-04-2010, 12:57 PM

This hubs from eBay r awesome! I had them on for a month already and had no problem and saving alot of money on gas from new bearing
*Update 4/24/11*
I been driving with this for about a year I hit the curve 3x from the front distorted 2 rims and still running perfect!!!! Highly recommend this!!

upsdude · 12-04-2010, 02:33 PM

s14 front hubs use a 32mm pinch bolt. if yours weren't pinched then maybe the previous owner had 5 lugs hubs and swapped in the 4 luggers when they sold you the car (who knows). i bought a set of front hubs from ebay, and they barely lasted a year. got a new pair of OE hub from ray at westco nissan for about 45 bucks more.
so just get the OE hubs for the front

s13fay92 · 02-28-2011, 01:29 PM

Great write up but I have a Q, I have my rear hubs off and was going to replace them with the 5 lug ones, but the 5 lug one wont slide on right, is it the hub or do i need to try harder? Thanks

10-02-2010, 08:23 PM	#1
twyztidmind Zilvia Member Join Date: Sep 2004 Location: Kansas Age: 33 Posts: 239 Trader Rating: (23) Feedback Score: 23 reviews	HOW TO: 5 Lug Conversion After searching i couldn't really find any good detailed 5 lug conversions before doing mine. So i decided to make one! This was done on my S14. I bought brand new hubs off ebay for 310 shipped. I also bought 5 lug rotors that were drilled and slotted for $115 shipped for all four. Parts Needed: 5 Lug hubs off SE 5 Lug Rotors off SE 5 Lug Wheels to finish off the setup Tools Needed: Impact Gun (If Available) Socket Set Ratchets Flat Head Screw Driver Hammer Axle Grease Axle Sockets 32mm and 36mm Wrench Set WD-40 Case of Beer Ok this is just a guide, I'm not responsible if you mess up your car! This is a medium difficulty project, if you can do an engine swap, you can do this! Hubs i bought off Ebay FRONTS: STEP 1: Remove dust cap, i used a flat head screw driver and a hammer, and hit it like a paint can going around it little by little. (Before i started I went ahead and painted the caliper with high heat paint ~ Half ass job but turned out ok ) ------------------- STEP 2: Remove axle nut 32MM if i remember right. I just loosened mine until i pulled the caliper off. ------------------- STEP 3: Remove Caliper and Rotor. ------------------- STEP 4: Now the hub should just slide right off. ------------------- STEP 5: Clean shaft and lube it with axle bearing grease. ------------------- STEP 6: Now you can slide on the new hub, re-torque the axle nut, and install the new rotor and the brake caliper. ------------------- Thats it for the fronts, now the rears are a little more complicated... REARS: STEP 1: Remove Cotter Pin & Axle Nut 36MM. (If you dont have an Impact you can remove center cap of wheel, put it back on the ground and use a break over bar) ------------------- STEP 2: Remove brake caliper and rotor ------------------- STEP 3: Remove the 4 bolts on the back side of the hub. You can turn the axle to were the indentions are to get access to each bolt. ------------------- STEP 4: Remove strut bolt, and the rest of the rear suspension shown in the pic. ------------------- STEP 5: Now you can pull the hub forward and remove the axle from housing. You can use a mallet to hit the axle to loosen it. ------------------- STEP 6: With the axle out of the way, you have good access to the hub. I used a sledge hammer (BFH) holding the spindle in my hand and pounded the hub out of the spindle. (This WILL ruin it, i didnt care i was throwing it all away) ------------------- STEP 7: I used an emery cloth to sand out the spindle hole, mine was rusty. ------------------- STEP 8: Now put in the new hub, torque down the bolts and reassemble everything in reverse order of which you took it off. You should end up looking like this! Thats it! Now you have a better selection in wheels. I bought some 350z touring wheels for a great price so thats what im rolling on for now. For $425 i had everything i needed to do the swap and brand spankin new! ENJOY!

10-05-2010, 03:43 PM	#11
MitchellBade Zilvia Member Join Date: Sep 2009 Location: Fort Collins, Colorado Posts: 205 Trader Rating: (8) Feedback Score: 8 reviews	Good work on the write up! __________________

10-05-2010, 03:46 PM	#12
Tae-Hyun Zilvia Junkie Join Date: May 2010 Location: tx Posts: 321 Trader Rating: (2) Feedback Score: 2 reviews	Well i guess you didnt search hard enough. How to: Install 5 lug hubs (only have pics of rear) Even though its just the rears, you get the idea. Nonetheless, your how too is nice with pics for front and rear. Nice. __________________ I only like you when you give me cookies.

10-05-2010, 05:45 PM	#14
Flashman Zilvia Member Join Date: Aug 2008 Location: 909,CA Posts: 200 Trader Rating: (10) Feedback Score: 10 reviews	i didnt unbolt any of the rear arms when i did my 5 lug __________________ http://instagram.com/night_flight__ https://soundcloud.com/flash-man

11-09-2010, 10:22 PM	#18
Drift_86 Post Whore! Join Date: Jan 2010 Location: Los Angeles, South Gate Age: 34 Posts: 3,684 Trader Rating: (60) Feedback Score: 60 reviews	Awesome thanks! I got the same 5lug off ebay __________________ Want to roll fenders, custom gauge pod pm me

10-02-2010, 08:41 PM	#2
Siberian Husky Zilvia Junkie Join Date: Dec 2005 Location: CA Posts: 411 Trader Rating: (4) Feedback Score: 4 reviews	nice CLEAN write up, just the meat n potatoes; i hate when people write DIY's and make them way too long--a way to stroke their ego for writing it up i guess. clean job though. what bearings did you use? im scared to just use the ebay bearings that come with the hubs. pics of the 350 touring wheels on your s13?

10-02-2010, 09:02 PM	#3
twyztidmind Zilvia Member Join Date: Sep 2004 Location: Kansas Age: 33 Posts: 239 Trader Rating: (23) Feedback Score: 23 reviews	Thanks! I used the bearings that came with it, not going to lie, they did look iffy but we dont track this car or anything so i wanted to see how they would hold up as a DD (will keep you guys updated) No pics of the wheels just yet, getting new tires on them right now, it's an S14 btw..

10-02-2010, 09:13 PM	#4
azndoc Post Whore! Join Date: Feb 2006 Location: Los Angeles Age: 39 Posts: 9,487 Trader Rating: (47) Rides Gallery: azndoc Feedback Score: 47 reviews	An easier way to get the rear hubs out is to unbolt the 4 bolts halfway and then use a rubber mallet pounding it out. Doesn't damage anything and comes out really easy. Good job on the write up

10-02-2010, 10:25 PM	#6
Ares240SX Leaky Injector Join Date: Sep 2006 Location: Nor Cal Age: 37 Posts: 141 Trader Rating: (0) Feedback Score: 0 reviews	10 minutes of pounding with most rubber mallets renders them useless... another idea is to use some penetrating oil, and maybe some heat around the outside edges to free up your old hubs so you don't have to worry about damaging something you might be able to sell to make up for the project costs.

10-02-2010, 11:31 PM	#7
240sxvaj Nissanaholic! Join Date: Dec 2007 Location: So-Cal! Age: 31 Posts: 2,192 Trader Rating: (38) Feedback Score: 38 reviews	pix are good lol!

10-02-2010, 11:36 PM	#8
tqstarburst Zilvia FREAK! Join Date: Mar 2010 Location: Texas Age: 29 Posts: 1,314 Trader Rating: (2) Feedback Score: 2 reviews	good job man,nice write up,alot of s13 owners are gonna benefit from this

10-05-2010, 12:15 PM	#9
japordie Join Date: Oct 2010 Location: O Town Posts: 37 Trader Rating: (0) Feedback Score: 0 reviews	nice thread it's short and simple.

10-06-2010, 02:47 PM	#15
s141996 Zilvia Junkie Join Date: Sep 2010 Location: IE Age: 34 Posts: 324 Trader Rating: (6) Feedback Score: 6 reviews	im doing it and I dont have a hub puller and Im doin this right now its a bitch!

10-06-2010, 05:04 PM	#16
kuelee Zilvia Member Join Date: Jul 2009 Location: hot valley Age: 36 Posts: 258 Trader Rating: (1) Feedback Score: 1 reviews	Does this also go for s13? And does the front hubs just slide in? No bolts holding the hub?

10-08-2010, 02:39 AM	#17
s141996 Zilvia Junkie Join Date: Sep 2010 Location: IE Age: 34 Posts: 324 Trader Rating: (6) Feedback Score: 6 reviews	just got done with mine along with z32 vlsd and z32 front brakes took 2 days and alot of hrs since i didnt have much help, thanks ur write up was my refrence when i couldnt figure something out. /exhausted

11-09-2010, 11:00 PM	#19
XxCAPTAINxX Zilvia Member Join Date: May 2010 Location: hillsboro Age: 34 Posts: 181 Trader Rating: (0) Feedback Score: 0 reviews	im curious to know how the ebay hubs hold up. keep us updated please __________________

11-09-2010, 11:06 PM	#20
Krusty_s13 Zilvia Addict Join Date: May 2008 Location: Miami, FL Posts: 862 Trader Rating: (0) Feedback Score: 0 reviews	Ebay hubs are fine. I rocked them on my previous fastback for about 6 months as a dd and some drift events. No issues with them. Will do it again with my new s13

11-09-2010, 11:29 PM	#21
Drift_86 Post Whore! Join Date: Jan 2010 Location: Los Angeles, South Gate Age: 34 Posts: 3,684 Trader Rating: (60) Feedback Score: 60 reviews	Awesome thanks! I got the same 5lug off ebay __________________ Want to roll fenders, custom gauge pod pm me

11-24-2010, 11:22 PM	#23
s13coupedrfter Zilvia Addict Join Date: Aug 2005 Location: Socal Posts: 839 Trader Rating: (8) Feedback Score: 8 reviews	Cant say anything about ebay hubs, never used them. I have used Ichiba hubs and they are JUNK!!!! I went through 2 front sets of them and each time had a bearing failure within 1 day of daily driving. Yes...they were properly torqued down with a calibrated tq wrench that I use at work. The spindle was in perfict condition. I will never use Ichiba hubs again. I use OEM s14 hubs without any problems...cant go wrong with factory Nissan stuff. Yes they are more expensive but so is replacing China shit hubs all the time. Cool write-up, keep up the good work.

11-24-2010, 11:29 PM	#24
xBtony Zilvia FREAK! Join Date: Jun 2009 Location: SoCal 661 Posts: 1,481 Trader Rating: (21) Feedback Score: 21 reviews	awesome write up super helpful. Imma be doing this soon.

11-25-2010, 02:27 AM	#26
Slammed Assassin Nissanaholic! Join Date: Feb 2007 Location: Oxnard/SV Posts: 2,065 Trader Rating: (34) Feedback Score: 34 reviews	great writeup!!! __________________

11-25-2010, 10:21 AM	#27
twyztidmind Zilvia Member Join Date: Sep 2004 Location: Kansas Age: 33 Posts: 239 Trader Rating: (23) Feedback Score: 23 reviews	For an S13 its about the same if you buy the after market hubs (like the ones i got on ebay). But if you take parts off an S14 SE you will need the whole spindle and LCA for the fronts as well as boring out the strut bolt a little because S14 uses a bigger one iirc. Hope that helps

12-04-2010, 12:57 PM	#28
Drift_86 Post Whore! Join Date: Jan 2010 Location: Los Angeles, South Gate Age: 34 Posts: 3,684 Trader Rating: (60) Feedback Score: 60 reviews	This hubs from eBay r awesome! I had them on for a month already and had no problem and saving alot of money on gas from new bearing Update 4/24/11 I been driving with this for about a year I hit the curve 3x from the front distorted 2 rims and still running perfect!!!! Highly recommend this!! __________________ Want to roll fenders, custom gauge pod pm me Last edited by Drift_86; 04-23-2011 at 02:40 PM..

12-04-2010, 02:33 PM	#29
upsdude Post Whore! Join Date: Apr 2009 Location: Fontana (the good part) Posts: 2,721 Trader Rating: (46) Rides Gallery: upsdude Feedback Score: 46 reviews	s14 front hubs use a 32mm pinch bolt. if yours weren't pinched then maybe the previous owner had 5 lugs hubs and swapped in the 4 luggers when they sold you the car (who knows). i bought a set of front hubs from ebay, and they barely lasted a year. got a new pair of OE hub from ray at westco nissan for about 45 bucks more. so just get the OE hubs for the front

02-28-2011, 01:29 PM	#30
s13fay92 Zilvia Member Join Date: Oct 2010 Location: Nashville Age: 29 Posts: 219 Trader Rating: (10) Feedback Score: 10 reviews	Great write up but I have a Q, I have my rear hubs off and was going to replace them with the 5 lug ones, but the 5 lug one wont slide on right, is it the hub or do i need to try harder? Thanks

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode