Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk > S Chassis

S Chassis Technical discussion related to the S Chassis such as the S12, S13, S14, and S15.


Reply
 
Thread Tools Display Modes
Old 08-16-2011, 02:41 AM   #1
ShimiBoi
Zilvia Member
 
ShimiBoi's Avatar
 
Join Date: Feb 2009
Location: Hawthorne
Posts: 216
Trader Rating: (9)
ShimiBoi is an unknown quantity at this point
Feedback Score: 9 reviews
KA ka24de hesitation and misfire?? plz help!

like the title says i have a small problem, plz dont flame me...i did search and found some things that might help and tried them with no avail so any help will be appreciated
things that might help you help me:
nearly stock ka24de with
-intake
-secondary butterfly delete
-cat-back exhaust
-msd blaster ss
-new ngk iridiums
-new ngk wires
-new cap and rotor
-new ignition coil wire
-throttle body spacer
-working egr
-connected aiv
-fuel filter replaced about 5k ago
-s13 auto ecu on stock manual s13.
-stock injectors [email protected] ohms [email protected] ohms [email protected] ohms [email protected]

problems:
-at start car is very hesitant and doesnt want to go, but doesnt misfire...just kinda bogs down until about 2500rpm (cold start).
-after it starts going car seems to run well under load.
-while decelerating with very partial throttle (ie. to slow the car down but not too fast) in gear car misfires
-at ~2000 rpm (while decelerating in gear) misfires several times and car gets a lil jerky.
-in neutral and revving up car will occasionally misfire after 2k
-under full throttle no misfire is noticed
-gas mileage has dropped from ~26 to ~24mpg (due to the auto ecu i presume)
-starts up fine even when cold

thank you zilvians for your help ahead of time!
ShimiBoi is offline   Reply With Quote
Sponsored Links
Old 08-17-2011, 12:08 AM   #2
Frankiegamer
Zilvia Junkie
 
Join Date: Dec 2010
Location: Los Angeles
Age: 30
Posts: 324
Trader Rating: (8)
Frankiegamer is an unknown quantity at this point
Feedback Score: 8 reviews
You virgin! Did you get the LSD? Lol
Frankiegamer is offline   Reply With Quote
Old 08-17-2011, 01:35 AM   #3
ShimiBoi
Zilvia Member
 
ShimiBoi's Avatar
 
Join Date: Feb 2009
Location: Hawthorne
Posts: 216
Trader Rating: (9)
ShimiBoi is an unknown quantity at this point
Feedback Score: 9 reviews
Quote:
Originally Posted by Frankiegamer View Post
You virgin! Did you get the LSD? Lol
nah fuker....it was an open diff...u guys made me waste $4 and 2 hrs of my life hahaha
ShimiBoi is offline   Reply With Quote
Old 08-17-2011, 12:58 AM   #4
Butcher240sx
Zilvia Member
 
Butcher240sx's Avatar
 
Join Date: Oct 2010
Location: Houston Texas
Age: 40
Posts: 157
Trader Rating: (0)
Butcher240sx is an unknown quantity at this point
Feedback Score: 0 reviews
Replace the 02 sensor.
__________________
Don't Mess With Texas
Butcher240sx is offline   Reply With Quote
Old 08-17-2011, 01:34 AM   #5
ShimiBoi
Zilvia Member
 
ShimiBoi's Avatar
 
Join Date: Feb 2009
Location: Hawthorne
Posts: 216
Trader Rating: (9)
ShimiBoi is an unknown quantity at this point
Feedback Score: 9 reviews
Quote:
Originally Posted by Butcher240sx View Post
Replace the 02 sensor.
i just replaced the o2 a couple months ago (May i think)...could it be dead already? Thanks

Last edited by ShimiBoi; 08-17-2011 at 03:39 AM..
ShimiBoi is offline   Reply With Quote
Old 08-17-2011, 03:04 AM   #6
Butcher240sx
Zilvia Member
 
Butcher240sx's Avatar
 
Join Date: Oct 2010
Location: Houston Texas
Age: 40
Posts: 157
Trader Rating: (0)
Butcher240sx is an unknown quantity at this point
Feedback Score: 0 reviews
Try swapping mafs then ecu for ones known to be good. See if that helps. Test the chts also.
__________________
Don't Mess With Texas
Butcher240sx is offline   Reply With Quote
Old 08-17-2011, 03:39 AM   #7
ShimiBoi
Zilvia Member
 
ShimiBoi's Avatar
 
Join Date: Feb 2009
Location: Hawthorne
Posts: 216
Trader Rating: (9)
ShimiBoi is an unknown quantity at this point
Feedback Score: 9 reviews
Quote:
Originally Posted by Butcher240sx View Post
Try swapping mafs then ecu for ones known to be good. See if that helps. Test the chts also.
Sorry, but what is the chts? Will an s14 maf work on an s13? Thanks
ShimiBoi is offline   Reply With Quote
Old 08-17-2011, 04:55 AM   #8
Butcher240sx
Zilvia Member
 
Butcher240sx's Avatar
 
Join Date: Oct 2010
Location: Houston Texas
Age: 40
Posts: 157
Trader Rating: (0)
Butcher240sx is an unknown quantity at this point
Feedback Score: 0 reviews
You need a s13 mafs. Chts is cylinder head temp switch. Its the two wire sensor. The one wire is for the gauge.
__________________
Don't Mess With Texas
Butcher240sx is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 10:54 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™