Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk > S Chassis

S Chassis Technical discussion related to the S Chassis such as the S12, S13, S14, and S15.


Reply
 
Thread Tools Display Modes
Old 05-20-2019, 02:22 PM   #1
Reyes_
Leaky Injector
 
Reyes_'s Avatar
 
Join Date: May 2018
Location: orange county
Age: 23
Posts: 59
Trader Rating: (0)
Reyes_ is an unknown quantity at this point
Feedback Score: 0 reviews
s13 sr20det stall when warm issue!

ok so long story short, car ran perfect until i let it sit for a week, car was covered..
after sitting for a week i go to start car let it warm up take it out around the block driving normal, then it stalls out randomly and i tried starting it, cranking and getting fuel and spark and no start. i have to let the car cool down before i can start it again..boost,afr,engine temp look normal, no boost leaks, changed out cts and checked to see if maf has a change to idle when i unplug it and it does so that means maf is working. any recommendations on what it can be? or suggestions?

specs
red top sr20det 62 ecu
all stock except for
fmic
hks bov
isr fpr
tomei srm7960 turbo
tomei manifold
full 3 in straight pipe

and no i hardly drive car as it is not tuned yet running stock ecu, car always ran perfect when i drove it around

link on the bottom to see video of issue

https://youtu.be/LsULhE-vtOQ

https://youtu.be/LsULhE-vtOQ


Sent from my iPhone using Tapatalk
Reyes_ is offline   Reply With Quote
Sponsored Links
Old 05-20-2019, 02:22 PM   #2
Reyes_
Leaky Injector
 
Reyes_'s Avatar
 
Join Date: May 2018
Location: orange county
Age: 23
Posts: 59
Trader Rating: (0)
Reyes_ is an unknown quantity at this point
Feedback Score: 0 reviews
uploaded video twice my bad guys lol


Sent from my iPhone using Tapatalk
Reyes_ is offline   Reply With Quote
Old 05-21-2019, 12:49 PM   #3
jedi03
Nissanaholic!
 
Join Date: Jul 2008
Location: albuquerque
Posts: 1,784
Trader Rating: (8)
jedi03 is on a distinguished road
Feedback Score: 8 reviews
check grounds and fuses, gfs car had issue where main fuse was blown but when cold the fuse would make contact then when hot would die like that...also check fuel pressure, ecu...sounds like something is expanding enough to keep car from going...also clean fuel filter
jedi03 is offline   Reply With Quote
Old 05-22-2019, 07:36 AM   #4
Kingtal0n
Post Whore!
 
Kingtal0n's Avatar
 
Join Date: Jul 2005
Location: South Florida
Age: 38
Posts: 4,649
Trader Rating: (17)
Kingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond repute
Feedback Score: 17 reviews
Send a message via AIM to Kingtal0n
All the videos shows is sr20 idle lean.

Either it has a vacuum leak around the maf or a bad O2 sensor

-unplug the O2 sensor
-pressure test the plumbing from compressor to engine to 20psi of pressure

or a maintenance issue i.e.
-clogged/bad injectors
-bad tps/cts/maf
-bad pcv plumbing

or a maf placement issue involving the turbo (can't see the turbo in the pic or plumbing so guess)
i.e. maf is too close to the turbo or something
Kingtal0n is offline   Reply With Quote
Old 05-23-2019, 08:05 PM   #5
Reyes_
Leaky Injector
 
Reyes_'s Avatar
 
Join Date: May 2018
Location: orange county
Age: 23
Posts: 59
Trader Rating: (0)
Reyes_ is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by Kingtal0n View Post
All the videos shows is sr20 idle lean.

Either it has a vacuum leak around the maf or a bad O2 sensor

-unplug the O2 sensor
-pressure test the plumbing from compressor to engine to 20psi of pressure

or a maintenance issue i.e.
-clogged/bad injectors
-bad tps/cts/maf
-bad pcv plumbing

or a maf placement issue involving the turbo (can't see the turbo in the pic or plumbing so guess)
i.e. maf is too close to the turbo or something


excuse all the excess vacuum lines, was mocking up



Sent from my iPhone using Tapatalk
Reyes_ is offline   Reply With Quote
Old 05-23-2019, 08:02 PM   #6
Reyes_
Leaky Injector
 
Reyes_'s Avatar
 
Join Date: May 2018
Location: orange county
Age: 23
Posts: 59
Trader Rating: (0)
Reyes_ is an unknown quantity at this point
Feedback Score: 0 reviews
update

replaced cts again

checked for vacuum leaks looks good

checked for loose grounds

checked spark plugs

took off turbo timer

checked to see if tps is getting correct voltage and yes 5

checked o2 sensor and it’s damaged & replaced with a working one

it did seem alittle better and took longer for it to stall out..

car is still stalling when at idle after 7 mins

when reving it temps bounces also rpm tach after finish revin it bounces down to 0

also checked all fuses and looks good

help plz...

also will be checking iacv?... dont think that it can be that maybe but


Sent from my iPhone using Tapatalk
Reyes_ is offline   Reply With Quote
Old 05-23-2019, 08:03 PM   #7
Reyes_
Leaky Injector
 
Reyes_'s Avatar
 
Join Date: May 2018
Location: orange county
Age: 23
Posts: 59
Trader Rating: (0)
Reyes_ is an unknown quantity at this point
Feedback Score: 0 reviews
will check w compression plumbing idea soon and will maf placement seems fine and accurate to where it should


Sent from my iPhone using Tapatalk
Reyes_ is offline   Reply With Quote
Old 05-27-2019, 12:12 PM   #8
Reyes_
Leaky Injector
 
Reyes_'s Avatar
 
Join Date: May 2018
Location: orange county
Age: 23
Posts: 59
Trader Rating: (0)
Reyes_ is an unknown quantity at this point
Feedback Score: 0 reviews
car is running perfect guys! replaced o2 sensor w oem one and disconnected battery terminals and ecu then repluged and runs perfect, thanks guys


Sent from my iPhone using Tapatalk
Reyes_ is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 03:20 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™