ca18det build thread!! - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

frftw · 09-01-2009, 12:05 PM

Hey everyone! after i bolted my motor in with my brother last night i decided that it is time for a build thread! i have an s13 hatch in prime rust free condition with a ca18det.
here are some pics:

so clean! (check out the 180sx rear garnish!!)

godspeed intercooler kit. i know its too big for the stock turbo but the turbo is gonna get bigger soon hopefully

anyone need ac or ps??

trust downpipe, apex1 afc neo, greddy rz bov!!!

check my homemade hockey puck motor mounts! (only grade 8 hardware was used for obvious reasons)

if anyone needs 2 borrow an engine lift on the east coast i got you!

my sister on the lift...

anyway, im new to nissans, before this i had a honda but decided to upgrade to somthing a little more rear wheel drive.
i will post updates as often as possible but school is starting tomorrow so im gonna b busy, and i got to apply to college and were moving in a couple of weeks so i gotta try to get this car moving soon!!

1'st question: how do i remove whats left of the ca driveshaft so i can bolt on the stock one? i looked but couldnt seem to find an obvious solution, do i remove the shifter assembally and do it from inside the tranny? just a thought

thanks for any help!
-alex

frftw · 09-01-2009, 02:51 PM

just ordered a 255lph fuel pump and nismo tranny mount from john at 240sxmotoring!

ranger240 · 09-01-2009, 02:54 PM

not gonna make any comments about your sister other than on this site you can expect to get some

frftw · 09-01-2009, 03:20 PM

shes 14, i hope that changes things...

*DALAZ_68* · 09-01-2009, 03:22 PM

Quote:

Originally Posted by frftw

shes 14, i hope that changes things...

nope...

first thing ill suggest...dont be cheap...get real mounts...especially with a motor of this age, ull find out...ill leave it at that...

*DALAZ_68* · 09-01-2009, 03:28 PM

Quote:

Originally Posted by frftw

Hey everyone! after i bolted my motor in with my brother last night i decided that it is time for a build thread! i have an s13 hatch in prime rust free condition with a ca18det.
here are some pics:

so clean! (check out the 180sx rear garnish!!)

godspeed intercooler kit. i know its too big for the stock turbo but the turbo is gonna get bigger soon hopefully

anyone need ac or ps??

trust downpipe, apex1 afc neo, greddy rz bov!!!

check my homemade hockey puck motor mounts! (only grade 8 hardware was used for obvious reasons)

if anyone needs 2 borrow an engine lift on the east coast i got you!

my sister on the lift...

anyway, im new to nissans, before this i had a honda but decided to upgrade to somthing a little more rear wheel drive.
i will post updates as often as possible but school is starting tomorrow so im gonna b busy, and i got to apply to college and were moving in a couple of weeks so i gotta try to get this car moving soon!!

1'st question: how do i remove whats left of the ca driveshaft so i can bolt on the stock one? i looked but couldnt seem to find an obvious solution, do i remove the shifter assembally and do it from inside the tranny? just a thought

thanks for any help!
-alex

i dont understand ur question

rephrase that english mess please

Z33dori · 09-01-2009, 03:39 PM

whats wrong with hockey puck motor mounts...

they work awesome

*DALAZ_68* · 09-01-2009, 03:44 PM

Quote:

Originally Posted by Z33dori

whats wrong with hockey puck motor mounts...

they work awesome

fuck that mess...hockey have there purpose in the name...hockey...and guess what...motor mounts have there purpose in there name...

hit up these guys for a great price

http://zilvia.net/f/members/eat-motorsports.html

RacerX1 · 09-01-2009, 05:16 PM

Quote:

Originally Posted by frftw

but decided to upgrade to somthing a little more rear wheel drive.
i will post updates

I LOLed, a little more RWD? Versus a little less?

*DALAZ_68* · 09-01-2009, 09:40 PM

Quote:

Originally Posted by RacerX1

I LOLed, a little more RWD? Versus a little less?

yeah man, dont u get it...he went from a rwd bicycle to a rwd car...

Horse Powah > Human powah

brewster240 · 09-01-2009, 09:55 PM

Quote:

Originally Posted by DALAZ_68

i dont understand ur question

rephrase that english mess please

wtf did you have to quote that whole thing? instead of "bold" you could have just deleted the rest.

Quote:

Originally Posted by frftw

just ordered a 255lph fuel pump and nismo tranny mount from john at 240sxmotoring!

east coast is pretty big? where you at? i have a bunch of random ca shit.

also, the driveshaft just slides out, no bolts, no c clips.

brewster240 · 09-01-2009, 09:56 PM

oh, also, hokey pucks suck as mounts for another reason.

factory mounts are actually offset.

with the pucks, you arent lined up right, because you just slide the bolt through.

*DALAZ_68* · 09-01-2009, 10:14 PM

Quote:

Originally Posted by brewster240

wtf did you have to quote that whole thing? instead of "bold" you could have just deleted the rest.

east coast is pretty big? where you at? i have a bunch of random ca shit.

also, the driveshaft just slides out, no bolts, no c clips.

Quote:

Originally Posted by brewster240

oh, also, hokey pucks suck as mounts for another reason.

factory mounts are actually offset.

with the pucks, you arent lined up right, because you just slide the bolt through.

maybe learn how to multi quote b4 u try to bitch at me about how i do things...

btw i was on my phone and didnt know there were that many pics...now im just not gonna edit

and yes Brewster is right...the offset othe CA mounts are different...

frftw · 09-01-2009, 10:16 PM

Quote:

Originally Posted by brewster240

oh, also, hokey pucks suck as mounts for another reason.

factory mounts are actually offset.

with the pucks, you arent lined up right, because you just slide the bolt through.

the offset makes the motor sit higher so my hockey pucks make the motor sit lower
lower motor=lower center of gravity=better handling
that doesn't sound so bad to me!

on the topic of the driveshaft, should i use a gear puller or something to slide it out or can i just use human power?

also, why is it so damn hard to remove the front bumper?? on my honda it was just a few easy bolts and i was done, today i found myself using 8 sockets+adapters to get to a bolt that i still cant get off (front right nut next to headlight attaching bumper to front of fender)

went to home depot and got some awesome tools, rustolium, bondo and a nos energy drink (that shits like crack).
im gonna flat black the front and rear bumpers and the trunk for now to make up for crappy paint and im using the bondo to cheaply fill the spoiler holes in the trunk third break light and rear wiper hole. might paint the rest black or have the flat black painted properly to match the car after i try the flat black out

what grits should i use to sand the paint?? im gonna go look for a diy now!

frftw · 09-01-2009, 10:18 PM

oh, and i live in greenwich ct in between stamford and port chestor ny

brewster240 · 09-01-2009, 10:23 PM

Quote:

Originally Posted by DALAZ_68

maybe learn how to multi quote b4 u try to bitch at me about how i do things...

btw i was on my phone and didnt know there were that many pics...now im just not gonna edit

and yes Brewster is right...the offset othe CA mounts are different...

i multiquoted you perfectly, then i had another thought.

Quote:

Originally Posted by frftw

the offset makes the motor sit higher so my hockey pucks make the motor sit lower
lower motor=lower center of gravity=better handling
that doesn't sound so bad to me!

on the topic of the driveshaft, should i use a gear puller or something to slide it out or can i just use human power?

offset, as in front/rear, not up down. take a stock mount, look at it from the side. the stud that goes into the subframe is not lined up with the one that goes into mount bracket.

the driveshaft doesnt need a puller. just slides out with your hand. if its stuck, it may have gotten jammed in the shipping container on the way here. have fun with that.

Quote:

Originally Posted by frftw

oh, and i live in greenwich ct in between stamford and port chestor ny

i see. im in brewster, north/opposite end of 684. if you need any parts or help, feel free to pm me, or aim: chugger2k

*DALAZ_68* · 09-01-2009, 10:24 PM

Quote:

Originally Posted by frftw

the offset makes the motor sit higher so my hockey pucks make the motor sit lower
lower motor=lower center of gravity=better handling
that doesn't sound so bad to me!

on the topic of the driveshaft, should i use a gear puller or something to slide it out or can i just use human power?

also, why is it so damn hard to remove the front bumper?? on my honda it was just a few easy bolts and i was done, today i found myself using 8 sockets+adapters to get to a bolt that i still cant get off (front right nut next to headlight attaching bumper to front of fender)

went to home depot and got some awesome tools, rustolium, bondo and a nos energy drink (that shits like crack).
im gonna flat black the front and rear bumpers and the trunk for now to make up for crappy paint and im using the bondo to cheaply fill the spoiler holes in the trunk third break light and rear wiper hole. might paint the rest black or have the flat black painted properly to match the car after i try the flat black out

what grits should i use to sand the paint?? im gonna go look for a diy now!

if ur gonna use lower center gravity as ur excuse for cheapin out, lol

why not just get actual mounts that sit lower...like say Drift Freaqs mounts
but hey what do i know,not something thats gonna rattle ur car, ive only wrenched on my motor for over a 2 1/2 years, and know 3 locals who have built these fuckers to push 400+. but w/e

why are u going to flat black, save and make it look clean, the paint isnt that bad...bah different strokes for diff folks...ive already lost intrest in this thread...

frftw · 09-02-2009, 04:08 PM

ill probably replace the hockey pucks when i have a bit more money. but for now other than the harsh rattle i dont see a downfall in performance from using the mounts if there is one please let me know!

well, time to work on the car, ill update tonight after im done

oh, and cut me some slack, i have only been working on cars since last november and this is my first turbo car and my first nissan.

sorry about the underlines

kikcaffine · 09-02-2009, 04:18 PM

I...I... I dont know where to begin. This is my first post so you need to feel honored with that. I broke my zilvia cherry with you.

First like everyone else said, quit half assing this install and get motor mounts for the car. You can get some nismo's for about 225 IIRC.

Secondly paint the car to not look like shit, your making us CA owners look bad.

Thirdly you think your sister being 14 is a problem? Its not.

frftw · 09-02-2009, 04:21 PM

i pm'd eat about their pricing on the motor mounts and im gonna check out Drift Freaqs as well.

frftw · 09-05-2009, 08:36 PM

i havent really gotten much done over the past couple of days because of school but now im back. anyway, im installing my intercooler and can figure out how to remove the battery tray. im trying to pry it off but it wont come loose. i know i have to drill a hole in the car to get the cold pipe through but i also want to remove the battery tray. whats the best way to do this?

ranger240 · 09-08-2009, 11:49 PM

http://zilvia.net/f/tech-talk/141288...y-removal.html

gotta use the search button... people on this forum will start to really flame you bad..

is that a 1991 with leather/ original 5speed? i wonder if its the one i almost bought in 2002.. where did the owners before you live? if it changed owners around fall 2002 in CT with about 100,000 miles then it very well may be.

keep the gray.. clean it up though. gl with your build, just make sure to put at least a few hours at it consistantly. you dont want to loose momentum with the build and have it drag on for months

09-01-2009, 12:05 PM	#1
frftw Zilvia Member Join Date: Aug 2009 Location: usa Posts: 171 Trader Rating: (2) Feedback Score: 2 reviews	ca18det build thread!! Hey everyone! after i bolted my motor in with my brother last night i decided that it is time for a build thread! i have an s13 hatch in prime rust free condition with a ca18det. here are some pics: so clean! (check out the 180sx rear garnish!!) godspeed intercooler kit. i know its too big for the stock turbo but the turbo is gonna get bigger soon hopefully anyone need ac or ps?? trust downpipe, apex1 afc neo, greddy rz bov!!! check my homemade hockey puck motor mounts! (only grade 8 hardware was used for obvious reasons) if anyone needs 2 borrow an engine lift on the east coast i got you! my sister on the lift... anyway, im new to nissans, before this i had a honda but decided to upgrade to somthing a little more rear wheel drive. i will post updates as often as possible but school is starting tomorrow so im gonna b busy, and i got to apply to college and were moving in a couple of weeks so i gotta try to get this car moving soon!! 1'st question: how do i remove whats left of the ca driveshaft so i can bolt on the stock one? i looked but couldnt seem to find an obvious solution, do i remove the shifter assembally and do it from inside the tranny? just a thought thanks for any help! -alex

09-01-2009, 03:39 PM	#7
Z33dori Post Whore! Join Date: Dec 2006 Location: Riverview, FL Age: 32 Posts: 5,557 Trader Rating: (12) Feedback Score: 12 reviews	whats wrong with hockey puck motor mounts... they work awesome __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

09-01-2009, 02:51 PM	#2
frftw Zilvia Member Join Date: Aug 2009 Location: usa Posts: 171 Trader Rating: (2) Feedback Score: 2 reviews	just ordered a 255lph fuel pump and nismo tranny mount from john at 240sxmotoring!

09-01-2009, 03:20 PM	#4
frftw Zilvia Member Join Date: Aug 2009 Location: usa Posts: 171 Trader Rating: (2) Feedback Score: 2 reviews	shes 14, i hope that changes things...

09-01-2009, 09:56 PM	#12
brewster240 Zilvia FREAK! Join Date: Dec 2006 Location: tampa bay, fl Age: 38 Posts: 1,042 Trader Rating: (2) Feedback Score: 2 reviews	oh, also, hokey pucks suck as mounts for another reason. factory mounts are actually offset. with the pucks, you arent lined up right, because you just slide the bolt through.

09-01-2009, 10:18 PM	#15
frftw Zilvia Member Join Date: Aug 2009 Location: usa Posts: 171 Trader Rating: (2) Feedback Score: 2 reviews	oh, and i live in greenwich ct in between stamford and port chestor ny

09-02-2009, 04:08 PM	#18
frftw Zilvia Member Join Date: Aug 2009 Location: usa Posts: 171 Trader Rating: (2) Feedback Score: 2 reviews	ill probably replace the hockey pucks when i have a bit more money. but for now other than the harsh rattle i dont see a downfall in performance from using the mounts if there is one please let me know! well, time to work on the car, ill update tonight after im done oh, and cut me some slack, i have only been working on cars since last november and this is my first turbo car and my first nissan. sorry about the underlines

09-02-2009, 04:18 PM	#19
kikcaffine Zilvia Addict Join Date: Aug 2009 Location: Marietta, Ga Posts: 713 Trader Rating: (2) Feedback Score: 2 reviews	I...I... I dont know where to begin. This is my first post so you need to feel honored with that. I broke my zilvia cherry with you. First like everyone else said, quit half assing this install and get motor mounts for the car. You can get some nismo's for about 225 IIRC. Secondly paint the car to not look like shit, your making us CA owners look bad. Thirdly you think your sister being 14 is a problem? Its not.

09-02-2009, 04:21 PM	#20
frftw Zilvia Member Join Date: Aug 2009 Location: usa Posts: 171 Trader Rating: (2) Feedback Score: 2 reviews	i pm'd eat about their pricing on the motor mounts and im gonna check out Drift Freaqs as well.

09-05-2009, 08:36 PM	#21
frftw Zilvia Member Join Date: Aug 2009 Location: usa Posts: 171 Trader Rating: (2) Feedback Score: 2 reviews	i havent really gotten much done over the past couple of days because of school but now im back. anyway, im installing my intercooler and can figure out how to remove the battery tray. im trying to pry it off but it wont come loose. i know i have to drill a hole in the car to get the cold pipe through but i also want to remove the battery tray. whats the best way to do this?