s13 right rear brake caliper repeatedly going bad - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

TriniTT · 12-16-2010, 08:04 PM

Hey all, I have an s13 240sx, and my rr caliper keeps going bad. Here's the story.

I recently did a full 5-lug swap. The right rear wheel bearing was bad, so I replaced it with a good one. Not long after, I realized that caliper had begun to leak. I kept adding fluid until I could find a good used caliper. It got worse quickly, so I replaced it with a known good working one. A few days later, this one began to leak and got worse quickly as well. I quit using my ebrake when I parked, and just kept it in gear.

I found another good used one, and threw it in thinking maybe the second was just a fluke. I started using my ebrake again after it seemed like this one was good for a few days. Now it's begun to leak as well.

Does anyone have any suggestions as to why the caliper seal keeps going bad? Could the spindle be bent from the bad wheel bearing? The pads are good, and the rotor was brand new as well when I did the 5-lug swap. There isn't any strange noise or anything, just the seal repeatedly going bad.

I'm out of ideas here. Any suggestions are greatly appreciated. Thanks!

Jonnie

modulation · 12-17-2010, 02:43 PM

On a stock s13/s14 240sx the ebrake has nothing to do with hydraulics, it's a cable.

Where is your caliper leaking from? Where the pistons or? Where the hose is?
Did you replace the crush washer that goes in between the hose and the caliper?

Sileighty_85 · 12-17-2010, 03:59 PM

buy a New Remanufactured one. If that one goes bad then you got a problem

TriniTT · 12-17-2010, 04:21 PM

Quote:

Originally Posted by modulation

On a stock s13/s14 240sx the ebrake has nothing to do with hydraulics, it's a cable.

Where is your caliper leaking from? Where the pistons or? Where the hose is?
Did you replace the crush washer that goes in between the hose and the caliper?

As I mentioned in my initial post, it's leaking from the piston seal. I rebuilt one with new oem seals and it's still doing the same thing. This is crazy.

modulation · 12-19-2010, 09:52 AM

Quote:

Originally Posted by TriniTT

As I mentioned in my initial post, it's leaking from the piston seal. I rebuilt one with new oem seals and it's still doing the same thing. This is crazy.

Maybe the rebuild kit sucks, or you suck at rebuilding them (don't take it personally.)

I'd try a new one instead. I have a dirt poor friend who was able to get some rear replacements pretty cheap, so they can't be that pricey new. I can understand wanting to learn and rebuild yourself, but it doesn't seem like that is working out.

TriniTT · 12-19-2010, 11:55 AM

Quote:

Originally Posted by modulation

Maybe the rebuild kit sucks, or you suck at rebuilding them (don't take it personally.)

I'd try a new one instead. I have a dirt poor friend who was able to get some rear replacements pretty cheap, so they can't be that pricey new. I can understand wanting to learn and rebuild yourself, but it doesn't seem like that is working out.

I'm a mechanic. This isn't my first rodeo.

modulation · 12-19-2010, 04:20 PM

Quote:

Originally Posted by TriniTT

I'm a mechanic. This isn't my first rodeo.

Did you use the same brand rebuild kit both times?

TriniTT · 12-20-2010, 05:42 PM

Quote:

Originally Posted by modulation

Did you use the same brand rebuild kit both times?

I only rebuilt it once. The second caliper I got from a friend off a known working car. Honestly, it might all be coincidence. I'm going to throw on another used one in a day or so and see if it works. It was free so I figure I might as well try it.

240sxrb25 · 12-20-2010, 05:45 PM

sure you dont have a bad hose that spraying on the caliper making you think its the seal.
oh and this aint no rodeo

TriniTT · 12-21-2010, 06:02 PM

Quote:

Originally Posted by 240sxrb25

sure you dont have a bad hose that spraying on the caliper making you think its the seal.
oh and this aint no rodeo

Positive. The piston seal is clearly broken when I remove the piston.

1slowM6 · 01-12-2011, 01:54 PM

I have the same exact problem,I can't figure it out either

codyace · 01-12-2011, 04:07 PM

Honestly, with these being a wear item, and used at that, you can never really tell how good the actual piston is (regardless of it looking 'good'). We see situations like this all the time at our shop, and it's partly the reason why we always suggest going with a new or profesionally rebuilt caliper (plus by the time you add in the labor of a rebuild, it's often cheaper just to install a new caliper and get it out of the shop).

Not doubting your ability, but with the variables assocaited in a used part, and new OEM kit, it's hard to tell if the used part is even original either.

FWIW: You are obviously pushing the piston back in with the right tool, i assume.

12-16-2010, 08:04 PM	#1
TriniTT Zilvia Junkie Join Date: Jan 2009 Location: Birmingham, AL Age: 36 Posts: 444 Trader Rating: (6) Feedback Score: 6 reviews	s13 right rear brake caliper repeatedly going bad Hey all, I have an s13 240sx, and my rr caliper keeps going bad. Here's the story. I recently did a full 5-lug swap. The right rear wheel bearing was bad, so I replaced it with a good one. Not long after, I realized that caliper had begun to leak. I kept adding fluid until I could find a good used caliper. It got worse quickly, so I replaced it with a known good working one. A few days later, this one began to leak and got worse quickly as well. I quit using my ebrake when I parked, and just kept it in gear. I found another good used one, and threw it in thinking maybe the second was just a fluke. I started using my ebrake again after it seemed like this one was good for a few days. Now it's begun to leak as well. Does anyone have any suggestions as to why the caliper seal keeps going bad? Could the spindle be bent from the bad wheel bearing? The pads are good, and the rotor was brand new as well when I did the 5-lug swap. There isn't any strange noise or anything, just the seal repeatedly going bad. I'm out of ideas here. Any suggestions are greatly appreciated. Thanks! Jonnie

12-17-2010, 03:59 PM	#3
Sileighty_85 Post Whore! Join Date: Dec 2006 Location: Misawa, Japan Posts: 6,815 Trader Rating: (8) Feedback Score: 8 reviews	buy a New Remanufactured one. If that one goes bad then you got a problem __________________ 後輪駆動車１番 1989 Built SR GT2871R -363whp 1998 S14 W/RB25- 250ish (For Now) 1986 SR86 - 200ish 1990 R32 GTR - 320hp Don't Buy Engines from JDM-Online http://zilvia.net/f/businesses/207457-jdm-online.html Don't Buy XS-Power or SSAC Shit

01-12-2011, 04:07 PM	#12
codyace Post Whore! Join Date: Dec 2004 Location: Poconos, PA Age: 36 Posts: 8,030 Trader Rating: (58) Feedback Score: 58 reviews	Honestly, with these being a wear item, and used at that, you can never really tell how good the actual piston is (regardless of it looking 'good'). We see situations like this all the time at our shop, and it's partly the reason why we always suggest going with a new or profesionally rebuilt caliper (plus by the time you add in the labor of a rebuild, it's often cheaper just to install a new caliper and get it out of the shop). Not doubting your ability, but with the variables assocaited in a used part, and new OEM kit, it's hard to tell if the used part is even original either. FWIW: You are obviously pushing the piston back in with the right tool, i assume. __________________ *Want Air Conditioning in your SR20 Swapped car? Check out www.sr20acbrackets.com for more information! Quest Alternator Conversions for SR20!* Check my Group Buy! Tired of lousy internal gates? Go external wastegate with one of my manifolds, Check out my group buy

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

12-17-2010, 02:43 PM	#2
modulation Zilvia Member Join Date: Apr 2008 Location: San Jose Posts: 191 Trader Rating: (0) Feedback Score: 0 reviews	On a stock s13/s14 240sx the ebrake has nothing to do with hydraulics, it's a cable. Where is your caliper leaking from? Where the pistons or? Where the hose is? Did you replace the crush washer that goes in between the hose and the caliper?

12-20-2010, 05:45 PM	#9
240sxrb25 Zilvia Junkie Join Date: Aug 2006 Location: omaha, ne Age: 31 Posts: 451 Trader Rating: (2) Feedback Score: 2 reviews	sure you dont have a bad hose that spraying on the caliper making you think its the seal. oh and this aint no rodeo

01-12-2011, 01:54 PM	#11
1slowM6 Leaky Injector Join Date: May 2010 Location: florida Age: 30 Posts: 62 Trader Rating: (0) Feedback Score: 0 reviews	I have the same exact problem,I can't figure it out either