1jz gte in my 240/silvia....pics - Page 2 - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

SoSideways · 06-07-2006, 11:05 PM

Yeah, black non powered door panels from Melbourne, FL!

hahaha

Glad to see the engine in the car ready to roll!

1Via! · 06-07-2006, 11:29 PM

Thats a pretty nice. The 1jz is one of few 6 cylinder engines I would put in my car.
Of course, you realize that you need the jzx81 front end on the s13 now. You'll be monumentally laaame if you dont swap the front end.

khmerguy618 · 06-10-2006, 06:29 AM

man this looks like its coming along quite nice, any updates??

sc300turbo · 06-10-2006, 10:05 AM

well i guess ill be lame cause i like the s13 silvia front...its staying that way...

as for updates..
brand new steel braided fuel lines are run..fuel tank was dropped and cleaned....2 year old gas is nasty!!!
added in my walbro fuel pump
picking up the modified koyo radiator today....
engine tranny and drive shaft are complete.....new water pump...timming belt...valve cover gaskets and grommets...plugs are nice and clean....new redline tranny fluid.....redline synthetic motor oil....are in....coolant is ready to go once i get the radiator back and my wiring guy is comming over today to look at it.....
im hoping by the next 2 weeks it will be driving.....
ill keep ya posted...
once the radiator is mounted and all i will snap some more pics....
Jeff

Sil Beer S13 · 06-10-2006, 11:02 AM

wow, i wanted to do something like that, but dont have the time to mess with fabricating stuffs.

looks good.

mmdb · 12-02-2006, 11:18 AM

Any updates on this project? What's the total cost of this thus far?

freeman · 12-02-2006, 01:26 PM

nice project.. looking good

sc300turbo · 12-03-2006, 07:37 PM

its been a long tough road...but im loving working on the car...the car was starte then dies...lost ignition...couldnt figure out why......turrned out when i swapped the water pump and all i managed t pinch the crank angle sensor and shorted the wires.....finally tracked it down and got it started agian to realize the stock twin turbos were bad.......swapped those....got it started agian...now need to finish wiring...get the custom exahust made......get intercooler piping made.....and bleed the clutch line...thats beeen a pin in my ass for something that should be so easy...
hoping to get it driving by jan....
ill post some newer pics tommorrow...
Jeff

BigVinnie · 12-03-2006, 08:06 PM

Project looks good Jeff. I'm shure you will enjoy the 1Jz as it is a bit more rev happy than the 2Jz. Has good 6cylinder torque as well. Hope to see it running by January.

Flybert · 12-03-2006, 09:42 PM

Ditch the clutch line loop if you still have it. Impossible to bleed with that trash in there.

sc300turbo · 12-04-2006, 05:09 AM

the clutch line loop is removed and i did a custom line because the slave is now on the drivers side of the car......

i made a custom steel braided line with fittings but could never get fluid to come out of the bleeder screw.....i replaced the slave cylinder and tried agian...nothting...i made a custom hard line and got fluid to finally come out of the bleeder screw now i need to get a friend to pump while i try to bleeed....

im praying to get it going...i cant wait to drive the piss out of this car
i still need to buy a carbon fiber hoood too...

SlowCoupe · 12-04-2006, 09:32 AM

what kind of ems are you using?

LB.Motoring · 12-04-2006, 09:42 AM

hey what did you end up doing with the lights and the grill off the clip?

wanna let me buy them :P

azndummie · 12-04-2006, 10:01 AM

thats pretty sick! Good job on the work so far

sc300turbo · 12-04-2006, 01:00 PM

clips and all parts were sold a long time ago...sorry.....

as for ems i have a stock ecu with a chipped board from japan....which i dont know for sure yet but 99% of those boards remove the boost cut, fuel cut, speeed limiter and turn up boost and fuel a lil bit...
with that ecu and an afc i should be able to easily meet my power goals.......i dont want to go stand alone but if i have to i will.....need to get it running solid with the current set up 1st

sc300turbo · 12-04-2006, 01:05 PM

couple newer pics....as you can see i pieced together piping just to make a connection on the intercooler...all new piping will be made shortly...
Jeff

ranger2339 · 12-04-2006, 01:46 PM

Sweet bro. I am doing a 1J with a GT35r .68ar in my onevia, should be killer.

Ax

SC_S13 · 12-04-2006, 10:42 PM

hehe toyota power in nissan chassis. thats awesome. did you have to do anything major to the drivetrain? or is that soon to come. 2 thumbs up!

origin_s135 · 12-05-2006, 06:24 PM

wow. looks very good. tell us how it feel, handles, etc.

Tenchuu · 04-02-2007, 08:16 PM

http://www.wftv.com/news/11493988/detail.html#

this wouldn't happen to be you would it?

stupid police, but that is still trouble.

trybal · 04-02-2007, 08:34 PM

woah..... i wonder? although that car had a different bumper on it

xblack240x · 04-02-2007, 08:43 PM

Nice build, post pics and a dyno sheet when your done... You make it look so easy =) I don't think anyone would dislike this project... I know I certainly don't...

KA-T_240 · 04-02-2007, 08:46 PM

The car looks sweet. any numbers with the new setup?

I dont think that car is even the same color as the one in this thread, the oil pan also looks wierd.

jeeper_x · 04-02-2007, 08:49 PM

dang..........now i understand y that guy revived the thread.....

zugoi · 04-02-2007, 09:24 PM

looks good man, keep up the good work.

Ian · 04-02-2007, 09:32 PM

Anyone notice they said it was a skyline in that article...it's clearly an S13 w/ silvia headlights

Tenchuu · 04-02-2007, 10:17 PM

well look at this thread, look at the later light blue pics with the triple projectors, look at the pic of the oil pan on his install, then match that pic to the oil pan of the 1JZ in that same colored car upside down in the article.

question: How many dual projector with yellow fog lights light blue 1JZ S13s are there out there?

educated guess: 1 to veary veary few.

kevtrinh · 04-02-2007, 10:26 PM

so im guessing it was him...

kouki_s14 · 04-02-2007, 10:34 PM

both in florida too

TheTimanator · 04-02-2007, 10:38 PM

Quote:

Originally Posted by Tenchuu

http://www.wftv.com/news/11493988/detail.html#

this wouldn't happen to be you would it?

stupid police, but that is still trouble.

well, if it is him I doubt he will be getting on here admitting to it since he fled the scene. It was a nice car with an idiot for a driver apparently. I grew up Orlando and street racing was a big problem down there. Tons of modified cars with young unexperienced drivers being irresponsible.

Tenchuu: agreed, the oil pan looks the same.

on another note: the troopers are clueless....lol

06-10-2006, 06:29 AM	#33
khmerguy618 Nissanaholic! Join Date: Apr 2003 Location: 408 san jeezy CA Age: 39 Posts: 2,001 Trader Rating: (11) Feedback Score: 11 reviews	man this looks like its coming along quite nice, any updates?? __________________ Watch speed channel 12/9 @7.30PM for drifting at HIN! [email protected] IF you bought stuff from me write me a review HERE \|\|VEXMOTORSPORTS \|\| DMAX-USA \|\| RPS CLUTCH \|\| BAB AUTOBODY\|\|

06-10-2006, 10:05 AM	#34
sc300turbo Zilvia Member Join Date: Feb 2002 Posts: 205 Trader Rating: (1) Feedback Score: 1 reviews	well i guess ill be lame cause i like the s13 silvia front...its staying that way... as for updates.. brand new steel braided fuel lines are run..fuel tank was dropped and cleaned....2 year old gas is nasty!!! added in my walbro fuel pump picking up the modified koyo radiator today.... engine tranny and drive shaft are complete.....new water pump...timming belt...valve cover gaskets and grommets...plugs are nice and clean....new redline tranny fluid.....redline synthetic motor oil....are in....coolant is ready to go once i get the radiator back and my wiring guy is comming over today to look at it..... im hoping by the next 2 weeks it will be driving..... ill keep ya posted... once the radiator is mounted and all i will snap some more pics.... Jeff __________________ 89 silvia/1JZGTE 6765 dbb E85 527rwhp

12-03-2006, 07:37 PM	#38
sc300turbo Zilvia Member Join Date: Feb 2002 Posts: 205 Trader Rating: (1) Feedback Score: 1 reviews	its been a long tough road...but im loving working on the car...the car was starte then dies...lost ignition...couldnt figure out why......turrned out when i swapped the water pump and all i managed t pinch the crank angle sensor and shorted the wires.....finally tracked it down and got it started agian to realize the stock twin turbos were bad.......swapped those....got it started agian...now need to finish wiring...get the custom exahust made......get intercooler piping made.....and bleed the clutch line...thats beeen a pin in my ass for something that should be so easy... hoping to get it driving by jan.... ill post some newer pics tommorrow... Jeff __________________ 89 silvia/1JZGTE 6765 dbb E85 527rwhp

12-03-2006, 08:06 PM	#39
BigVinnie Zilvia FREAK! Join Date: Apr 2003 Location: Walnut Crizzle, Crackifornia Age: 42 Posts: 1,266 Trader Rating: (0) Rides Gallery: BigVinnie Feedback Score: 0 reviews	Project looks good Jeff. I'm shure you will enjoy the 1Jz as it is a bit more rev happy than the 2Jz. Has good 6cylinder torque as well. Hope to see it running by January. __________________

12-04-2006, 05:09 AM	#41
sc300turbo Zilvia Member Join Date: Feb 2002 Posts: 205 Trader Rating: (1) Feedback Score: 1 reviews	the clutch line loop is removed and i did a custom line because the slave is now on the drivers side of the car...... i made a custom steel braided line with fittings but could never get fluid to come out of the bleeder screw.....i replaced the slave cylinder and tried agian...nothting...i made a custom hard line and got fluid to finally come out of the bleeder screw now i need to get a friend to pump while i try to bleeed.... im praying to get it going...i cant wait to drive the piss out of this car i still need to buy a carbon fiber hoood too... __________________ 89 silvia/1JZGTE 6765 dbb E85 527rwhp

06-07-2006, 11:05 PM	#31
SoSideways Post Whore! Join Date: Apr 2003 Location: 你老母 Posts: 4,371 Trader Rating: (4) Feedback Score: 4 reviews	Yeah, black non powered door panels from Melbourne, FL! hahaha Glad to see the engine in the car ready to roll!

06-07-2006, 11:29 PM	#32
1Via! Zilvia Junkie Join Date: Jan 2006 Location: Seattle/Olympia, WA Age: 35 Posts: 510 Trader Rating: (3) Rides Gallery: 1Via! Feedback Score: 3 reviews	Thats a pretty nice. The 1jz is one of few 6 cylinder engines I would put in my car. Of course, you realize that you need the jzx81 front end on the s13 now. You'll be monumentally laaame if you dont swap the front end.

06-10-2006, 11:02 AM	#35
Sil Beer S13 Zilvia FREAK! Join Date: Jul 2003 Location: Chino!...NOT CHINO HILLS! Age: 39 Posts: 1,117 Trader Rating: (0) Feedback Score: 0 reviews	wow, i wanted to do something like that, but dont have the time to mess with fabricating stuffs. looks good.

12-02-2006, 11:18 AM	#36
mmdb Zilvia FREAK! Join Date: Apr 2003 Location: 240sx Posts: 1,558 Trader Rating: (20) Feedback Score: 20 reviews	Any updates on this project? What's the total cost of this thus far?

12-02-2006, 01:26 PM	#37
freeman Leaky Injector Join Date: Nov 2006 Location: socal Posts: 74 Trader Rating: (0) Feedback Score: 0 reviews	nice project.. looking good

12-03-2006, 09:42 PM	#40
Flybert Post Whore! Join Date: Mar 2003 Location: none Posts: 3,862 Trader Rating: (7) Feedback Score: 7 reviews	Ditch the clutch line loop if you still have it. Impossible to bleed with that trash in there.

12-04-2006, 09:32 AM	#42
SlowCoupe Zilvia Junkie Join Date: Feb 2004 Location: New Orleans Age: 36 Posts: 341 Trader Rating: (0) Feedback Score: 0 reviews	what kind of ems are you using? __________________

12-04-2006, 09:42 AM	#43
LB.Motoring Post Whore! Join Date: Jul 2006 Location: SòCal♥ Age: 35 Posts: 5,840 Trader Rating: (1) Rides Gallery: LB.Motoring Feedback Score: 1 reviews	hey what did you end up doing with the lights and the grill off the clip? wanna let me buy them :P __________________ Robby Leuer

12-04-2006, 10:01 AM	#44
azndummie Zilvia FREAK! Join Date: Dec 2005 Location: orange county Posts: 1,362 Trader Rating: (14) Feedback Score: 14 reviews	thats pretty sick! Good job on the work so far __________________

12-04-2006, 01:00 PM	#45
sc300turbo Zilvia Member Join Date: Feb 2002 Posts: 205 Trader Rating: (1) Feedback Score: 1 reviews	clips and all parts were sold a long time ago...sorry..... as for ems i have a stock ecu with a chipped board from japan....which i dont know for sure yet but 99% of those boards remove the boost cut, fuel cut, speeed limiter and turn up boost and fuel a lil bit... with that ecu and an afc i should be able to easily meet my power goals.......i dont want to go stand alone but if i have to i will.....need to get it running solid with the current set up 1st __________________ 89 silvia/1JZGTE 6765 dbb E85 527rwhp

12-04-2006, 01:05 PM	#46
sc300turbo Zilvia Member Join Date: Feb 2002 Posts: 205 Trader Rating: (1) Feedback Score: 1 reviews	couple newer pics....as you can see i pieced together piping just to make a connection on the intercooler...all new piping will be made shortly... Jeff __________________ 89 silvia/1JZGTE 6765 dbb E85 527rwhp

12-04-2006, 01:46 PM	#47
ranger2339 Zilvia Junkie Join Date: May 2006 Location: MINNESOTA Age: 40 Posts: 520 Trader Rating: (1) Feedback Score: 1 reviews	Sweet bro. I am doing a 1J with a GT35r .68ar in my onevia, should be killer. Ax

12-04-2006, 10:42 PM	#48
SC_S13 Zilvia Addict Join Date: Nov 2006 Location: Santa Cruz Posts: 936 Trader Rating: (15) Feedback Score: 15 reviews	hehe toyota power in nissan chassis. thats awesome. did you have to do anything major to the drivetrain? or is that soon to come. 2 thumbs up! __________________

12-05-2006, 06:24 PM	#49
origin_s135 Zilvia FREAK! Join Date: Dec 2006 Location: 湾区域 Posts: 1,333 Trader Rating: (1) Feedback Score: 1 reviews	wow. looks very good. tell us how it feel, handles, etc.

04-02-2007, 08:16 PM	#50
Tenchuu Post Whore! Join Date: Apr 2004 Location: Oregon Age: 39 Posts: 2,474 Trader Rating: (8) Rides Gallery: Tenchuu Feedback Score: 8 reviews	http://www.wftv.com/news/11493988/detail.html# this wouldn't happen to be you would it? stupid police, but that is still trouble.

04-02-2007, 08:34 PM	#51
trybal Zilvia Junkie Join Date: Nov 2005 Location: Seattle wa Posts: 299 Trader Rating: (0) Feedback Score: 0 reviews	woah..... i wonder? although that car had a different bumper on it

04-02-2007, 08:43 PM	#52
xblack240x Zilvia Junkie Join Date: Mar 2007 Location: Bay Area Posts: 555 Trader Rating: (2) Feedback Score: 2 reviews	Nice build, post pics and a dyno sheet when your done... You make it look so easy =) I don't think anyone would dislike this project... I know I certainly don't...

04-02-2007, 08:46 PM	#53
KA-T_240 Nissanaholic! Join Date: Sep 2005 Location: Moorhead, MN Age: 34 Posts: 1,788 Trader Rating: (0) Feedback Score: 0 reviews	The car looks sweet. any numbers with the new setup? I dont think that car is even the same color as the one in this thread, the oil pan also looks wierd. __________________

04-02-2007, 09:24 PM	#55
zugoi Zilvia Junkie Join Date: Aug 2003 Location: Bay area Posts: 560 Trader Rating: (0) Feedback Score: 0 reviews	looks good man, keep up the good work. __________________ Drunk posting FTW!

04-02-2007, 10:17 PM	#57
Tenchuu Post Whore! Join Date: Apr 2004 Location: Oregon Age: 39 Posts: 2,474 Trader Rating: (8) Rides Gallery: Tenchuu Feedback Score: 8 reviews	well look at this thread, look at the later light blue pics with the triple projectors, look at the pic of the oil pan on his install, then match that pic to the oil pan of the 1JZ in that same colored car upside down in the article. question: How many dual projector with yellow fog lights light blue 1JZ S13s are there out there? educated guess: 1 to veary veary few.

04-02-2007, 10:26 PM	#58
kevtrinh Zilvia Junkie Join Date: May 2006 Location: Richmond,VA Posts: 370 Trader Rating: (0) Feedback Score: 0 reviews	so im guessing it was him...

04-02-2007, 10:34 PM	#59
kouki_s14 Zilvia FREAK! Join Date: Jan 2004 Location: Los Angeles Posts: 1,550 Trader Rating: (0) Feedback Score: 0 reviews	both in florida too

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode