Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk > S Chassis

S Chassis Technical discussion related to the S Chassis such as the S12, S13, S14, and S15.


Reply
 
Thread Tools Display Modes
Old 02-06-2021, 04:36 PM   #1
se7en_
Leaky Injector
 
Join Date: Sep 2010
Location: alberta
Posts: 123
Trader Rating: (1)
se7en_ is an unknown quantity at this point
Feedback Score: 1 reviews
1991 Silvia RHD LS swap questions.

Hey all, I'm in the middle of an LS swap on my Silvia RHD.

Couple questions I can't seem to find even with searching.

1. The valve cover hits the Clutch master cylinder. I know I need a larger bore master with my t56 clutch(more on this later) and that will just make the problem worse. Is there a physically shorter master with a bigger bore that works? perhaps clocking it differently? Anyone done this without using reverse swing pedals and putting the master inside the cab?

2. I'm going to be running an AR5 trans from a colorado/canyon. It uses the t56 clutch and shares the output spline count from the t56 as well. The shifter location is terrible. Does someone make a shifter that moves the shifter location back about 7 inches? anyone know if the AR5 and T56 transmission is similar length? Google isn't helping much.

Any help would be greatly appreciated.

Thanks.
se7en_ is offline   Reply With Quote
Sponsored Links
Old 02-06-2021, 04:38 PM   #2
UJCD
 
Join Date: Nov 2016
Location: VE
Posts: 27
Trader Rating: (0)
UJCD is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by se7en_ View Post
Hey all, I'm in the middle of an LS swap on my Silvia RHD.

Couple questions I can't seem to find even with searching.

1. The valve cover hits the Clutch master cylinder. I know I need a larger bore master with my t56 clutch(more on this later) and that will just make the problem worse. Is there a physically shorter master with a bigger bore that works? perhaps clocking it differently? Anyone done this without using reverse swing pedals and putting the master inside the cab?

2. I'm going to be running an AR5 trans from a colorado/canyon. It uses the t56 clutch and shares the output spline count from the t56 as well. The shifter location is terrible. Does someone make a shifter that moves the shifter location back about 7 inches? anyone know if the AR5 and T56 transmission is similar length? Google isn't helping much.

Any help would be greatly appreciated.

Thanks.

Use the AR5 form the solstice


Sent from my iPhone using Tapatalk
UJCD is offline   Reply With Quote
Old 02-06-2021, 04:39 PM   #3
se7en_
Leaky Injector
 
Join Date: Sep 2010
Location: alberta
Posts: 123
Trader Rating: (1)
se7en_ is an unknown quantity at this point
Feedback Score: 1 reviews
Further searching says that the t56 is .15" shorter then an AR5, so the off the shelf driveshafts will work. I still have issues with the clutch master and shifter locations though.
se7en_ is offline   Reply With Quote
Old 02-06-2021, 04:50 PM   #4
se7en_
Leaky Injector
 
Join Date: Sep 2010
Location: alberta
Posts: 123
Trader Rating: (1)
se7en_ is an unknown quantity at this point
Feedback Score: 1 reviews
Solstice trans are very hard to find in Canada, But I'll keep my eyes out. Any ideas on the clutch master cylinder issue?
se7en_ is offline   Reply With Quote
Old 02-07-2021, 12:12 PM   #5
se7en_
Leaky Injector
 
Join Date: Sep 2010
Location: alberta
Posts: 123
Trader Rating: (1)
se7en_ is an unknown quantity at this point
Feedback Score: 1 reviews
Any ideas on the clutch master issue? I can't be the only one with this issue.
se7en_ is offline   Reply With Quote
Old 02-08-2021, 06:28 PM   #6
shoottothrill
Leaky Injector
 
Join Date: Jan 2020
Location: Arizona
Age: 28
Posts: 86
Trader Rating: (1)
shoottothrill is just really niceshoottothrill is just really niceshoottothrill is just really niceshoottothrill is just really niceshoottothrill is just really niceshoottothrill is just really niceshoottothrill is just really niceshoottothrill is just really nice
Feedback Score: 1 reviews
I know serial 9 makes a ton of shifter adapters for different stuff. Have you checked with them about the shifter placement issue?
shoottothrill is offline   Reply With Quote
Old 02-22-2021, 06:32 AM   #7
SilentKilla
 
Join Date: Jun 2003
Location: perth
Posts: 1
Trader Rating: (0)
SilentKilla is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by se7en_ View Post
Hey all, I'm in the middle of an LS swap on my Silvia RHD.

Couple questions I can't seem to find even with searching.

1. The valve cover hits the Clutch master cylinder. I know I need a larger bore master with my t56 clutch(more on this later) and that will just make the problem worse. Is there a physically shorter master with a bigger bore that works? perhaps clocking it differently? Anyone done this without using reverse swing pedals and putting the master inside the cab?

2. I'm going to be running an AR5 trans from a colorado/canyon. It uses the t56 clutch and shares the output spline count from the t56 as well. The shifter location is terrible. Does someone make a shifter that moves the shifter location back about 7 inches? anyone know if the AR5 and T56 transmission is similar length? Google isn't helping much.

Any help would be greatly appreciated.

Thanks.
There's a few options on a RHD, I'm in the middle of an ADM S14A conversion to LS myself. Can look at a reverse swing clutch pedal conversion, or as logic suggests in finding a physically shorter clutch master.

I've gone with the following option, never mind the price it's not that much but wont really be a practical option in the US anyway: https://www.holmart.com.au/holden-cl...vu-v6-3.8-v8-5

How have you gone with starter motor clearance to the steering rack input shaft/valve body?

Last edited by SilentKilla; 02-22-2021 at 06:41 AM.. Reason: forgot the word 'rack'
SilentKilla is offline   Reply With Quote
Old 02-22-2021, 05:39 PM   #8
DiscountPirate
Zilvia Member
 
Join Date: Jul 2016
Location: SoCal
Posts: 189
Trader Rating: (0)
DiscountPirate is an unknown quantity at this point
Feedback Score: 0 reviews
I only know the RHD S13 aspect I don't know LS but I have seen custom stuff like Wilwood pedals and remote mount cylinders. Only other thing I recall is that the Z32 clutch master is a direct swap and larger bore but doubt it is that much shorter. Worst case depending on your clearances you might be able to grind/machine down a bit off cylinder and a bit off valve cover to fit.
DiscountPirate is offline   Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 06:54 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™