Z32 BMC flare fitting - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

nisileighty · 03-25-2017, 10:23 PM

Hi there, I'm doing the z32 BMC on my s13 with z32 brakes, but I'm not sure on where to get the middle flare fitting. Does anyone know? I already tried cutting them out of my stock one and it didn't work. Thanks!

SR20PWRALTY · 03-26-2017, 12:52 AM

I actually stick a hex key into the fitting and wiggle it out.

jdl1527 · 03-26-2017, 06:17 AM

I'm going through the same swap as you right now, when you say that you tried cutting out the old one, but it did not work, what do you mean?

Sent from my Nexus 6P using Tapatalk

nisileighty · 03-26-2017, 11:30 AM

Quote:

Originally Posted by jdl1527

I'm going through the same swap as you right now, when you say that you tried cutting out the old one, but it did not work, what do you mean?

Sent from my Nexus 6P using Tapatalk

When I was cutting it the Dremel went too far and nicked the fitting causing it to not create a proper seal

Sent from my iPhone using Tapatalk

jdl1527 · 03-26-2017, 01:11 PM

Ah, a better way would be to use the dremel to cut access behind the fitting and then use a punch or drill bit to hammer it out

Sent from my Nexus 6P using Tapatalk

nisileighty · 03-26-2017, 02:23 PM

Quote:

Originally Posted by jdl1527

Ah, a better way would be to use the dremel to cut access behind the fitting and then use a punch or drill bit to hammer it out

Sent from my Nexus 6P using Tapatalk

Right, realize that now lol. Do you know of anywhere you can buy those fittings?

jdl1527 · 03-26-2017, 04:46 PM

No, looked long and hard, your old BMC should have 3. If not, like I said I'm going through the same thing, I can send you one once I get mine out.

Sent from my Nexus 6P using Tapatalk

nisileighty · 03-26-2017, 08:00 PM

Quote:

Originally Posted by jdl1527

No, looked long and hard, your old BMC should have 3. If not, like I said I'm going through the same thing, I can send you one once I get mine out.

Sent from my Nexus 6P using Tapatalk

You'd be a life saver man. I'll float you a few bucks if you could mail me a few. Go ahead and shoot me a text at 206 566 9749. Thanks!

Sent from my iPhone using Tapatalk

SR20PWRALTY · 03-26-2017, 10:40 PM

Grab a hex tool or "L" wrench that fits in the fitting whole and wiggle it out from your old BMC. There no need to use a Dremel.

03-25-2017, 10:23 PM	#1
nisileighty Zilvia FREAK! Join Date: Feb 2016 Location: Seattle, WA Posts: 1,215 Trader Rating: (4) Feedback Score: 4 reviews	Z32 BMC flare fitting Hi there, I'm doing the z32 BMC on my s13 with z32 brakes, but I'm not sure on where to get the middle flare fitting. Does anyone know? I already tried cutting them out of my stock one and it didn't work. Thanks!

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

03-26-2017, 12:52 AM	#2
SR20PWRALTY Zilvia Junkie Join Date: Mar 2005 Location: SOCAL Posts: 579 Trader Rating: (13) Feedback Score: 13 reviews	I actually stick a hex key into the fitting and wiggle it out.

03-26-2017, 06:17 AM	#3
jdl1527 Join Date: Mar 2010 Location: Wisconsin Age: 36 Posts: 34 Trader Rating: (2) Feedback Score: 2 reviews	I'm going through the same swap as you right now, when you say that you tried cutting out the old one, but it did not work, what do you mean? Sent from my Nexus 6P using Tapatalk

03-26-2017, 01:11 PM	#5
jdl1527 Join Date: Mar 2010 Location: Wisconsin Age: 36 Posts: 34 Trader Rating: (2) Feedback Score: 2 reviews	Ah, a better way would be to use the dremel to cut access behind the fitting and then use a punch or drill bit to hammer it out Sent from my Nexus 6P using Tapatalk

03-26-2017, 04:46 PM	#7
jdl1527 Join Date: Mar 2010 Location: Wisconsin Age: 36 Posts: 34 Trader Rating: (2) Feedback Score: 2 reviews	No, looked long and hard, your old BMC should have 3. If not, like I said I'm going through the same thing, I can send you one once I get mine out. Sent from my Nexus 6P using Tapatalk

03-26-2017, 10:40 PM	#9
SR20PWRALTY Zilvia Junkie Join Date: Mar 2005 Location: SOCAL Posts: 579 Trader Rating: (13) Feedback Score: 13 reviews	Grab a hex tool or "L" wrench that fits in the fitting whole and wiggle it out from your old BMC. There no need to use a Dremel.