Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > General > Tech Talk

Tech Talk Technical Discussion About The Nissan 240SX and Nissan Z Cars


Reply
 
Thread Tools Display Modes
Old 02-20-2021, 09:44 PM   #1
astro.domine
 
Join Date: Jan 2019
Location: Seattle
Age: 28
Posts: 4
Trader Rating: (0)
astro.domine is an unknown quantity at this point
Feedback Score: 0 reviews
Help Identifying this SR Noise?

https://youtu.be/v2PrCewfMHE

Sounds kinda like a metallic clack/buzz, that only happens at ~1-3k RPM. It seems like the obvious culprit would be a noisy lifter, but I've bled my lifters many, many times and they all look to be in good condition. Noise becomes softer/quieter when warm.

Engine has been rebuilt with Wiseco pistons, Eagle rods, but I think it made this noise even before that. Subie 550cc injectors, Jim Wolf S3 cams, S15 turbo.

This doesn't sound like bottom-end noise, right? Could it be I need to re-shim the valves?
astro.domine is offline   Reply With Quote
Sponsored Links
Old 02-21-2021, 02:29 AM   #2
Kingtal0n
Post Whore!
 
Kingtal0n's Avatar
 
Join Date: Jul 2005
Location: South Florida
Age: 38
Posts: 4,646
Trader Rating: (17)
Kingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond repute
Feedback Score: 17 reviews
Send a message via AIM to Kingtal0n
The way it gets quieter when you rev usually means rod bearing or wrist pin failure


I admit it sounds like a top end noise but there aren't many types of load-based engine noises and bearing/piston is the most common

I really hope it isn't for you
__________________
5.3/4l80e/turbo 240sx playthrough:
https://tinyurl.com/turbo240
Kingtal0n is offline   Reply With Quote
Old 02-21-2021, 07:51 AM   #3
burnsauto
Premium Member
 
burnsauto's Avatar
 
Join Date: Dec 2006
Location: 717, PA
Age: 35
Posts: 3,153
Trader Rating: (5)
burnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfection
Feedback Score: 5 reviews
Send a message via AIM to burnsauto
piston slap? How does the noise relate to engine temp? Does it change at all?

Either way, that engine isn't staying together for too long, either because you take it apart, or it takes itself apart.
__________________
burnsauto is offline   Reply With Quote
Old 02-21-2021, 10:28 AM   #4
astro.domine
 
Join Date: Jan 2019
Location: Seattle
Age: 28
Posts: 4
Trader Rating: (0)
astro.domine is an unknown quantity at this point
Feedback Score: 0 reviews
Quote:
Originally Posted by Kingtal0n View Post
The way it gets quieter when you rev usually means rod bearing or wrist pin failure

I admit it sounds like a top end noise but there aren't many types of load-based engine noises and bearing/piston is the most common

I really hope it isn't for you
That would be truly disappointing. Thanks for the info though.
The pistons & wrist pins are new, and all the bearings are new, with clearances under .002".

Quote:
Originally Posted by burnsauto View Post
piston slap? How does the noise relate to engine temp? Does it change at all?

Either way, that engine isn't staying together for too long, either because you take it apart, or it takes itself apart.
Could it be piston slap if it has 160psi+ compression though?
The noise becomes much softer & almost disappears after it warms up.
astro.domine is offline   Reply With Quote
Old 02-21-2021, 01:19 PM   #5
Kingtal0n
Post Whore!
 
Kingtal0n's Avatar
 
Join Date: Jul 2005
Location: South Florida
Age: 38
Posts: 4,646
Trader Rating: (17)
Kingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond reputeKingtal0n has a reputation beyond repute
Feedback Score: 17 reviews
Send a message via AIM to Kingtal0n
New as in Forged aluminum low silicone alloy?

I've heard those pistons make a similar sort of noise. yes, 'piston slap' because the pistons need to warm up when they are set to manufacturer recommended piston to wall clearance.

But,
1. I've never heard it that loud before
2. If it really is cold piston slap, that noise is the pistons gradually wearing the bore into an oval shape (it will have scuff marks down the lateral sides of each bore)
3. Engines built with forged aluminum pistons and massive piston-wall clearances are not intended for cold start or to be operated while the oil is cold. They require oil temp minimum of around 170-185*F Before you can load the engine, otherwise, loading the loose piston from the top will create additional force which will further accelerate the bore wear.

generally, forged are not good pistons for daily drivers or street cars unless a low expansion aluminum specific alloy and closer piston-to-wall is used.

Now all of that said, if you told me those pistons are new but they are cast aluminum, I would suggest you have the wrong size pistons, improper machine work, something like that. It shouldn't rattle with a cast piston.
Also when you make a thread asking what this noise is it would be very helpful if you had mentioned that all of the bottom end parts are new, or the engine was just rebuilt, etc... Because in the video I and from the post I assumed it was a 200,000 miles high mileage beat up ruined sr20 engine and there is no way to tell any difference.
Kingtal0n is offline   Reply With Quote
Old 02-21-2021, 01:43 PM   #6
burnsauto
Premium Member
 
burnsauto's Avatar
 
Join Date: Dec 2006
Location: 717, PA
Age: 35
Posts: 3,153
Trader Rating: (5)
burnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfectionburnsauto is close to perfection
Feedback Score: 5 reviews
Send a message via AIM to burnsauto
yeah it could still be piston slap with good compression. Over time, the compression could go down as the rings wear more, but since it's a fresh rebuild you could still be getting good compression due to the freshness of the engine.

Try doing a leak down test to further check on things if you don't want to go elbow deep into the engine just yet, just know it's inevitable. Hopefully there is some sort of warranty from your engine builder if that winds up being the case.
__________________
burnsauto is offline   Reply With Quote
Reply

Bookmarks

Tags
clack, rattle, sr20det, valve noise


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 06:52 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™