jdm2191

can u manely move the auto driver side seatbelt & lock it so it don't go forward & it stays back?

Flicktitty

if you let the seatbelt go back, you can unplug the wire to the motor and it will stay in the back postion.

__________________
2JZ-GTE Swapped S13 Coupe - 1994 Supra Turbo

jdm2191

Which plug because there's 2?

hpipro4

the one from the motor.....or you can unplug the computer for it located in the center console....

jdm2191

oh so that little box that's next to the handbrake controls the seatbelt? & also what if they don't go back at all?

BoostedCoupe

Take off the plastic trim that goes under the quarter glasses. Shut the doors with the key on, then unplug the motor. And your done. IF you can not do that then i dunno

__________________
92 vert converted 5speed and other little things

hpipro4

yeah that box underneath the console is the computer for the power seat belts.....what do you mean they wont go back at all???aren't you trying to make them stay at the back so they dont move at all???

do this:

close all doors then turn the key to the "ON" position wait for the belts to go fully to the back and then unplug the connectors from the motor both sides if want both of them not to move ever....turn ignition off and youll be good to go.....

another one is to get s14 front seat belts and install it on ur car...will need modding on panels unless you get 180sx panels...

8869muscle

Had this same problem not long ago...apparently behind the rear side trim you can manually rotate the motor with a hex key...you have to remember to unplug the controller though..

jdm2191

what i meant by they dont go back at all is that when i turn my car on they dont go back they stay forward.....so i cant unplug the wire until they go back...

hpipro4

wooopsss..mis-read your post......then check motor connections and computer connections and i cant recall if there is a fuse for the power seat belt....you can also do what 8869muscle said....with the panels installed there should be round covering you can take that out and you should be able to get the hex without taking panels out...

jdm2191

Ok cool thanks for the help....

projectRDM

The rear quarter panel has a small round plug that pops off to access the motor. Use an M5 hex key and manually turn the motor to move the belt mechanism. Then take it to a dealer and have it warrantied.

__________________
FORMERLY R240NA

Learn what's really going on and protect your assets now before they're gone forever: www.paypalsucks.com

Phatz

The same thing happened to me bro. You gotta put some elbow grease in it and pull that ish back while the car is off. then pull the plug and forget about it.

OR..

Our cars have a lifetime warranty on seat belts. If you go to a Nissan service center at a dealership, they will inspect it and order new motors, tracks for FREEEEEEEE!!!

but I did option one.

__________________

alzahakar

Another option is the S14 seatbelt conversion. I did that to my S13 after the thing tried to kill me when I had to open the door to reach a keypad for my gated community.

d3m14n

+1 for this man. im gonna go to the nissan dealership and get my driver side rail replaced. they have been locked in the back position for as long as i can remember.

__________________
http://www.d3m14n.com/

amdnivram

so what do you need for them to replace the seatbelt motors?

Phatz

...you mean at the dealer?

I went first thing in the a.m. and had them inspect it... took like 2-3 hours.

then they told me they couldn't tell if it was the motor or the track so they were ordering both from Japan and the would be there in a couple weeks...

in the meantime, some dickhead pig gave me a no seatbelt ticket even though I had the hip belt on...$100, and i heard it triples if you get a second.

So thats why I just pulled it back and unplugged the brain.

__________________

amdnivram

ahh ok, so i can just show up at one of the dealership service center and tell them that mine arent working.. and etc.

__________________


http://silaudrey.blogspot.com/