Front tension rod - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Mecha_Trueno · 05-14-2014, 06:54 AM

I'm going to be replacing the front tension rods soon and just have a quick question. (It’s actually only the bushings that are knackered but thought I might as well change the whole arm)

I've read a few guides which advise that you should not tighten/torque the bolts until you put the tyres back on and lower the car to the ground or you will bust up the bushings. Has anyone ever had this problem? I just think it’ll be a bit difficult to tighten the bolts without the clearance for some leverage.

Kaifd3s · 05-14-2014, 10:31 AM

I tightened everything and just jacked up the hub that was attached to the corresponding tension rod.

Sindel713 · 07-31-2014, 09:00 AM

Just put in on ramps then finish tightening.

Croustibat · 07-31-2014, 09:27 AM

Problem is, unless you changed for an oem rubber bushing, you will end up with binding problems. PU bushings are fine as long as the arm only moves around an axis perpendicular to the bushing. Considering suspension arms on S chassis, only the rear lower arm bushings move like that.

The "tighten in on the ground" is the way to go if you want to limit binding. The easiest is to use a lift with ramps, if you can't you could always use ramps.

And the best way is to go rose/heim joint.

Sleepy_Steve · 08-01-2014, 08:57 AM

Quote:

Originally Posted by Croustibat

Problem is, unless you changed for an oem rubber bushing, you will end up with binding problems. PU bushings are fine as long as the arm only moves around an axis perpendicular to the bushing. Considering suspension arms on S chassis, only the rear lower arm bushings move like that.

The "tighten in on the ground" is the way to go if you want to limit binding. The easiest is to use a lift with ramps, if you can't you could always use ramps.

And the best way is to go rose/heim joint.

Very much this!

Sway bars can also be an acceptable use of polyurethane on our cars. So only 8 bushings total for PU.

05-14-2014, 06:54 AM	#1
Mecha_Trueno Join Date: Sep 2006 Location: London Age: 37 Posts: 5 Trader Rating: (0) Feedback Score: 0 reviews	Front tension rod I'm going to be replacing the front tension rods soon and just have a quick question. (It’s actually only the bushings that are knackered but thought I might as well change the whole arm) I've read a few guides which advise that you should not tighten/torque the bolts until you put the tyres back on and lower the car to the ground or you will bust up the bushings. Has anyone ever had this problem? I just think it’ll be a bit difficult to tighten the bolts without the clearance for some leverage.

05-14-2014, 10:31 AM	#2
Kaifd3s Zilvia Addict Join Date: Feb 2008 Location: Tamarac, Florida Age: 35 Posts: 694 Trader Rating: (16) Feedback Score: 16 reviews	I tightened everything and just jacked up the hub that was attached to the corresponding tension rod. __________________

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

07-31-2014, 09:00 AM	#3
Sindel713 Join Date: May 2014 Location: Houston Age: 30 Posts: 8 Trader Rating: (0) Feedback Score: 0 reviews	Just put in on ramps then finish tightening.

07-31-2014, 09:27 AM	#4
Croustibat Nissanaholic! Join Date: Aug 2011 Location: France - Toulouse Age: 41 Posts: 1,851 Trader Rating: (0) Feedback Score: 0 reviews	Problem is, unless you changed for an oem rubber bushing, you will end up with binding problems. PU bushings are fine as long as the arm only moves around an axis perpendicular to the bushing. Considering suspension arms on S chassis, only the rear lower arm bushings move like that. The "tighten in on the ground" is the way to go if you want to limit binding. The easiest is to use a lift with ramps, if you can't you could always use ramps. And the best way is to go rose/heim joint.