Installing 5 speed tranny help - Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Brandon240sx · 03-18-2018, 12:38 AM

Anyone run into this problem while doing a 5 speed swap? Went to bolt my tranny up tonight but couldn’t get it in there. I threw an Isis short throw on it before installing since it doesn’t look like it can really be changed without dropping the tranny again. Mainly having a problem getting the shifter through the hole and getting the bellhousing lined up at the same time. Any one have any idea how to do this? Can’t figure it out

derass · 03-18-2018, 01:22 AM

Do you have the motor mounts loosened, and the engine tilted back? Do you have a helper to muscle the trans back onto the engine?

tuzzio · 03-18-2018, 05:57 AM

Put the shifter in after the trans is in the car. You can leave the base plate bolted on and assemble the lever with the cover after.

Brandon240sx · 03-18-2018, 12:36 PM

Quote:

Originally Posted by derass

Do you have the motor mounts loosened, and the engine tilted back? Do you have a helper to muscle the trans back onto the engine?

Have a helper but didn’t loosen the motor mounts, gonna try doing that

Brandon240sx · 03-18-2018, 12:40 PM

Quote:

Originally Posted by tuzzio

Put the shifter in after the trans is in the car. You can leave the base plate bolted on and assemble the lever with the cover after.

I’ll try that if tilting the motor doesn’t work

*anti tyler* · 03-18-2018, 12:59 PM

Yeah these are fun to install with the engine already in.

Even more fun to install when the car is barely off the ground. Don't give up, I assure you, you can do it.

Also don't end up slicing your fingers off getting frustrated with it. That bellhousing is sharp as hell.

tuzzio · 03-19-2018, 08:09 AM

Quote:

Originally Posted by Brandon240sx

I’ll try that if tilting the motor doesn’t work

This is 10x easier than what you're about to do, and takes about 30 seconds once the trans is in.

*TheRealSy90* · 03-19-2018, 11:02 AM

Install the shifter after installing the transmission. It CAN be done with the proper wrenches. A 12mm flex-head ratchet wrench is perfect.

03-18-2018, 12:38 AM	#1
Brandon240sx Zilvia Member Join Date: Aug 2017 Location: Long Island, NY Posts: 156 Trader Rating: (0) Feedback Score: 0 reviews	Installing 5 speed tranny help Anyone run into this problem while doing a 5 speed swap? Went to bolt my tranny up tonight but couldn’t get it in there. I threw an Isis short throw on it before installing since it doesn’t look like it can really be changed without dropping the tranny again. Mainly having a problem getting the shifter through the hole and getting the bellhousing lined up at the same time. Any one have any idea how to do this? Can’t figure it out

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

03-18-2018, 01:22 AM	#2
derass Zilvia FREAK! Join Date: Jun 2010 Location: Toronto, ON Age: 33 Posts: 1,182 Trader Rating: (0) Feedback Score: 0 reviews	Do you have the motor mounts loosened, and the engine tilted back? Do you have a helper to muscle the trans back onto the engine?

03-18-2018, 05:57 AM	#3
tuzzio Nissanaholic! Join Date: Oct 2013 Location: Western Mass. Posts: 2,254 Trader Rating: (3) Feedback Score: 3 reviews	Put the shifter in after the trans is in the car. You can leave the base plate bolted on and assemble the lever with the cover after.