240sex_s14

Hello! my name is AJ and have been a member in these forums for quite some time now. I told myself with my next project!!! a build thread is a must to let the community see my blood, sweat, and slave money go to a good cause. My first car that I regret selling was a 95' base model that I converted into a kouki and installed a notchtop into it. The reasons why I sold my first 240 can turn into a book to be honest with me having 2 bikes at one point and almost dying from an accident. Long story short, I have been searching for a clean Shell but came across a working car that I couldn't pass up!!! So, let the fun begin!!!


I was in the market for a JDM vehicle and few state side FD's but I ended up buying a 1998 Nissan 240sx LE -Slicktop - Silver moss ~ Bone stockish / minor mods ~ Factory MT ~ roughly 200k miles on chassis / motor estimate due to cluster not working and stopped at 172k.


The transmission is grinding a little and the Motor is blowing white smoke here and there.... which I think both are ready to go! In my first 240 I did an SR swap with upgrades and this car I want to go with something more fun and aggressive!!! Little more info about the car mods below;


Current Mods:

• 300zx 30mm Cast iron Calipers + 300zx rears
• Drilled / Slotted Rotors
• Tein Suspension Unknown Type
• Stainless Steel Break lines + Clutch
• VIS Carbon fiber trunk
• 6k HID Headlights
• Mishimoto Rad
• Nismo Shifter
• Unknown Short Shifter
• Pioneer Radio
• JDM Front Bumper
• Silvia Hood Emblem
• Works Cr Kai: Fronts -18x8.5 ?? offset / Rears -18x9.5 ?? offset

As of 08/28/2017 I purchased my engine! so sit tight for pic and details about it!!!!
Went with 2JZ From an Astrio. 30-40k Miles on it. See below for Pics.







Enjoy the pics!











Front Rim/Rotor/Caliper



Rear Rim/Rotor/Caliper



More to come!!!!

s1421

Nice man! I was going to buy this car when it was being sold but i went with a s13 coupe instead! This car has potential goodluck in the build!

240sex_s14

Haha, I couldn't pass up the deal on this with the shape it was in. Well the chassis of course, not so much of the engine/trans though. I have big plans for this bad girl here! "Detail" is the key to this build. You know what they say...Go big or go Home hahaha.

240sex_s14

As Of 9/22/2017


While driving around I felt my brakes not gripping anymore and I went ahead and got some new rotors / pads. Got a sweet deal on the rotors which was $50 for front pair.





Car was too low for my jack so I had to improvise and get this bad boy up in the air. Bricks...cant never go wrong with bricks!





As I was taking off the rotors I noticed my SS brake lines were loose and a shiny part was glaring at me...Now I need to order a new set as I feel this is unsafe.





Anyways, I got the rotors and pads off...and looks like the previous owner used some shitty pads and the rotors were glazed like glass.









Now that I got some stuff on the way for replacement and also replaced...it came out looking good









As Of 9/24/2017


I stole (J.K) my friends pickup truck to pick this bad boy up!









I had NO cherry picker at the moment and got home late AF! so I had once again improvise and used two dollies with a tie down lined up with the driveway...it was low enough to yank the engine onto the dolly... With the right position it landed perfectly!!!





More to come as I ordered some parts! and took my car to get appraised for repaint. Stay tuned for the next set of stuff!!!!

240sex_s14

As of 10/04/17


I ordered the following;

• BC 264/264 Camshaft
• BC Cam Gears
• Greddy Timing Belt
• 1650CC FIC Injectors
• Turbo kit
• Xcessive Motor Mounts
• CD009 Transmission

just waiting for the parts to come in the mail or picked up at 9k Racing shop.

afishysilvia

Nice car, is this similar to the 95 yr green/gold color??

240sex_s14

Thanks! The 95-96 Color is called "Champagne Gold - Paint Code/ EM1"


The 97-98 Color is called "Silver Moss - Paint Code/ KR5"


The only color that comes close to the Silver moss color in the Nissan family would be off the Skyline R34 "Millennium Jade - Paint Code/ JW0" it has more of a green tint.

jr_ss

Clean car, should've bought different cams though. You'll neee springs to go with those cams FYI.

__________________
My SR20VET

240sex_s14

Thank you! I was really up in the air with what cams to go with


really? I've read a bunch of people swapping cams to the 264's and not having any problems with the stock springs. When people swapped to the 272/272 cams that's when the problems started.

jr_ss

All BC cams to my knowledge need to be degreed to get the cam to run right. With that said any aftermarket cam needs to be "optimized" for best results. Also, I just paid closer attention and you have Jz, not a Nissan engine, so they "may" not be as bad as their Nissan counter parts. However, usually the errors aren't limited to one manufacture.

__________________
My SR20VET

240sex_s14

haha yes, 2jz big single. You had me researching for stuff right now...gave me a slight of a "aww fuck" situation because I was about to start buying more stuff hahah.

tricky_ab

With those cam sizes, it's still considered "drop in" but it's recommend to do the springs since "you're already there". That's from my understanding of JZ engines anyways...

__________________
Instagram

Back for round two... 4 doors this time around...

240sex_s14

just contacted my connect, getting a pricing on the BC0300 Valve and Springs kit. If the price comes out cheap, ill go 272/272 and the BC spring kit.


but yeah you're right... better safe than sorry

240sex_s14

As of 10/09/2017

Picked up the following items.

• - S14 SPL Toe Arms (chrome)
• - S14 SPL Traction rods (chrome)
• - S14 Cusco Rear Upper Control Arms
• -Sikky Front Sway Bar

will post up pics of these items.




Thank you @CrimsonRockett for these items.

240sex_s14

Alright Guys, Sorry for the Delay! holidays came up then everything with my puppy heading to hospital, so everything had to be put on hold! but everything is good now and moving forward with my build! INC PIC HEAVY!

240sex_s14

Little Hoarding going on and Approval from my puppy!



Now for the Stuff!


Frist up Stage 3 - BC Camshaft 272/272 for the 2J





BC Camgears / Ordered the Wrong set for Non-VVTI when my motor is VVTI





BC Valve Spring Kit Stage 3





Greddy Timing Belt to replace the Old one.





Most expensive part thus far..wait I lied, I'll post a pic of that later.
FIC 1650's for my Thirsty 2J





Tein Inner & Outer setup.





Last but not least, My Xcessive Mounts for 2J + CD009 Trans.



More Pics to come, Just waiting for stuff in the mail! #BrokeXmas2017

240sex_s14

Little Quick Snap of my car currently before I rip her heart out.



Dropped off my Engine As of 11/25/17 to get Hot Tanked and Heads Assembled by my Tuner. Also Ordered my Turbo / Turbo Mani / Fuel Rail / FMIC.


Happy Holidays Zilvians.

s13driftnut

Looks good so far man, keep it up

__________________

Sailor

That took a turn quick, 2jz what a legendary engine to run. You car is so clean as well, really a great platform to start modifications. Looking forward to updates!

240sex_s14

Thank you! this weekend its Operation Takeout (Removing the KA and clean the remaining grease and prep for paint. Engine bay of course.


hahah, it sure did! I wanted a fast daily and came back to the car scene with a vengeance! A complete make over from the inside that is...2J or Bust! my first car was a SR20, I wanted something very different this time around.

afishysilvia

Love your car and build, IMO a V8 would have been the shit, but the I6 route is very cool and different too. That color is just so nice.

240sex_s14

haha, my cousin told me the same thing! but he's a big Chevy fan...also he's picking up a z06 and I told him my I6 will take him out once I'm done building it because JDM! also, I went turbo once and I will never go back to NA engines!! Thank you for the kind words!

afishysilvia

I just finished my V8 , we should get together sometime. I wanna see the color in person, I have the EM1 paint code. Was your bumper painted to match?

240sex_s14

Hell yeah man I'll be down! Sick! did you dyno to see what you're putting down? As for the front bumper it was painted to match but I need to repaint the entire car, the previous owner left it out in the sun and now...its peeling :-(

240sex_s14

Brief recap of the last 2 weekends.

• Pulled Ka/Trans *SOLD*
• Removed some stuff in engine bay
• Removed Dash/Dash bar (Getting ready to rewire front fuse box)
• Removed Battery tray
• Stitch Weld front end

I also took few parts to powder coating guy.

• 2J Valve Covers
• Upper Control Arms
• Lower Control Arms

The Valve Covers! I picked a sick color so hopefully it turns out the way I think it should. Control arms going with black since I don't want to go all crazy with color.


Also Amazon came through with some parts for the engine.


**SEE BELOW FOR PICS**

__________________
Check out my Build Thread!http://zilvia.net/f/showthread.php?t=650464

240sex_s14

This week I should be able to get some more done to the car and get the front end ready for primer and paint. I should also be looking into Cut / Splice / Solder / Heat shrinking the front fuse box to my glove compartment.

__________________
Check out my Build Thread!http://zilvia.net/f/showthread.php?t=650464

Sailor

Man that interior looks all too familiar, no dash. Keep it up

240sex_s14

haha, Thanks man! its coming along just want to finish it already and drive this bish!


This week I have to drop the rear sub frame and put the bushings on it, then degrease and prep front end for paint.

__________________
Check out my Build Thread!http://zilvia.net/f/showthread.php?t=650464

240sex_s14

Hello, Hello! Hopefully everyone had a good New Years and Xmas!


Started off my year with a cold but its alright...The sickness set me back on working on the car but its coming together slowly but surely. -See Below-


Pulled the Wiring Harness out, This weekend going to undo and redo the harness to the exact spot I want it inside the car.







I ended up removing the Battery Tray and found a tad bit of rust. Which I sanded and hit it with some Primer.


Before:





After :









Now to Finish Painting Engine Bay and Harness! Wish me luck! Stay posted!

__________________
Check out my Build Thread!http://zilvia.net/f/showthread.php?t=650464

Sailor

Don't let the cold get to you, keep it up