Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum

Go Back   Zilvia.net Forums | Nissan 240SX (Silvia) and Z (Fairlady) Car Forum > davirene


Conversation Between davirene and dOMEmE
Showing Visitor Messages 1 to 10 of 11
  1. dOMEmE
    01-13-2010 11:56 PM
    dOMEmE
    hoenstly i would go sil front on a coupe, if it was hatch pop-up fronts for sure....so far im diggin how hella clean your car looks!.ill try and post pics my car when i get it pretty. =] i like the rear sits on my car but i might pull the fenders and stick a 30mm spacer in the rear.
  2. davirene
    01-13-2010 11:29 PM
    davirene
    Ok so this is what happened once the rims were on.....the back end was to high and the front was filled in and looked good but the back was inset without the spacers. SO you can sort of see in this pic the front sticks out more than the back.



    When I get a chance I will take some new pics so you can see I lowered the back down. Then I put the spacers on...giving it the aggressive look.

    Here is an example of what look I want....but still undecided on Sylvia or popups?
  3. davirene
    01-13-2010 11:11 PM
    davirene
    10mm Will still be close depending on the rim itself. I have a 10mm with a 4mm = 14mm with the deep lugs on the front. On the back I had custom spacers which are 31mm with regular lugs cause the spacer itself has long studs already installed. Which gives me an aggressive look. I actually got 2 compliments today at the gas station and at the grocery store. People really like the way the car sits. They also think the rims are really expensive cause of the deep chrome lip.
  4. dOMEmE
    01-13-2010 07:35 PM
    dOMEmE
    oh my bad,just noticed what tire i posted, i have 225/40/18 all around actually...and my rim it hitting the coil...so do you think if up front i put a 10mm spacer with stock studs and buy those lugs ill be all in the clear? i just want to make sure you know before i spend money on the lugs and spacers..
  5. davirene
    01-13-2010 06:44 PM
    davirene
    Hey those gorilla lugs are exactly the same.....and I am not sure about your tire, 45 sounds a lil too tall? Are the tires hitting the coils or the rim?
    Im running 40 series but have it stretched. Thats also why I rolled my fenders. When I switch to coilovers and go a lil lower I will probably roll my fenders or go to aftermarket 30mm fenders.
  6. dOMEmE
    01-12-2010 07:10 PM
    dOMEmE
    lol...i was waitng for your response but i saw that you responded to me on your page so i never got notified,lol.... well then i made up my mind and im keeping the wheels. i am too running 224/45/18 alla round and only ran into trouble in the front becasue it hit coil...but now i know how they can be installed... hey do you think there lugs are the same one you have?

    Gorilla Small Diameter Tuner Lug Nut 21133ET:eBay Motors (item 330394091417 end time Jan-13-10 08:04:05 PST)
  7. dOMEmE
    01-10-2010 11:06 PM
    dOMEmE
    here ya go....dont know where i found it but i saved it...lol

  8. dOMEmE
    01-10-2010 11:01 PM
    dOMEmE
    your just like me, i hate staggered and im also going for the "VIP" "LUX" look, but i ran into the problem of them hitting my fenders up front and was wondering how you did it...so how much clearance do you have between inside of rim and coil with that 14mm spacer?....oh and what is the purpose of the deep corn lug nuts?
  9. davirene
    01-10-2010 10:58 PM
    davirene
    Hey I forgot to mention...you do simply have one of the best Avatar Pictures on the forum....I actually have done some research to find where you got it??? I actually came up with nothing......

    SO....where did you get it???
  10. davirene
    01-10-2010 10:55 PM
    davirene


    Yes Im running 18x9.5 +35 all around....I dont like the staggered look....and really wanted the JDM VIP (LUX) Look......but since funds are really tight for me....I dont have the cash for baller wheels....These XXR's cost me about $1000

    Now up front I have a 14mm Spacer (Due to Tein Springs) with some hard to find deep lugs....and the rear has a custom machine 31mm Spacer that is Hub Centric....So its a perfect fit with no chance of vibration or slippage. I did roll the rear fenders and lowered the the back down by about 3 inches.



All times are GMT -6. The time now is 11:05 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
vB.Sponsors
Copyright © 1998 - 2019, Zilvia.net™