FS Built S13 SR20DET Longblock & 5 Spd Trans W/ Cryotreated Gearset

[SRE30]

I had plans to swap this into my E30, but priorities have changed and I won't be needing this motor.

This motor has made 661whp/583ft lbs at 30psi with a T61/P-trim. It only has about 5 hours run time.

Saenz custom connecting rods
ARP rod bolts
JE 8.5:1 forged pistons
Chromeoly/steel compression rings
Nissan Motorsports main bolts
ARP head studs
Stock cams (sold the HKS cams a while back)
Crank pulley with welded 60-2 tooth crank trigger wheel

http://gallery.thevboard.com/showpic.php?dispsize=Original&album=Trav4011&pic=661whpS13.jpg

If you are looking for the foundation of your 600+ build this is it. Easy 10 second passes with a GT35R turbo and HKS stage 2 cam setup. Or a bullet proof block for your drift car. This motor was built to make tons of power reliably.

I'd rather sell the trans with the motor.

Serious inquiries pm for my phone number and additional info

I'd suggest emailing me at [email protected] as I am able to check that more frequently than logging on here.

Make me an offer.

I'll give it a few days here. After that it'll go on Ebay.

[DJPimpFlex]

I must say thats some pretty substantial lag. Kinda interested in the tranny, but you probably dont wanna hear my offer. lol.

[The Riot Hero]

I must say thats some pretty substantial lag. Kinda interested in the tranny, but you probably dont wanna hear my offer. lol.

what you mean? doesnt look bad at all, very on/off switch, but the lag is not bad at all, especially for that power level.

im also somewhat interested in the transmission if you decide to sell it seperate.

[SRE30]

Make an offer on the trans. If someone comes up and just wants the motor I'll have your offer.

[txrxs]

PM sent

[elixirvtec]

Do you have any pictures? What kind of price range you looking to get for it? Im in the market for a SR20 but im not rich

[SRE30]

I can get pics. I'm not in a bind to sell this motor, so I won't be just giving it away.

What would a stock longblock cost?

Figure easily over 1k in parts.

Assembled, tested, and ready to go once you pick the cam you want to use for your application.

[DJPimpFlex]

its like a fuckin switch at 4300. Thats not bad for that power, but its still a lot of lag.

[SRE30]

You could always use a smaller and/or faster spooling turbo.

This sale is just for the bare long block. No manifolds, no turbo, . . .bare longblock. Just wanted to make sure there was no confusion.

[SRE30]

not real sure what the current market is for a setup like this.

4k or best offer for the motor and trans = a decent asking price?

[turbodreams954]

to me that sounds reasonalbe especially since the trans is done right also. if i wanted an SR id be all over this. good luck though!

[TheSparo]

does it come w/ stock valvetrain? or new valve springs/retainers etc?

[SRE30]

stock valvetrain

[Buckness Monster]

pm's replied and a little bumpage

[SLUG]

what would you need besides a turbo to makes this run?
wiring and a intake mani. some cams. or maybe you got some stock cams laying around.
clutch?

[SRE30]

It's got the stock cams.

Off the top of my head you would need the manifolds, turbo, ecu, wiring harness, and other little things.

This is either a good setup for someone who has an sr and would just swap the blocks to get the forgedness, or someone who will be using this motor to it's potential and would be buying aftermarket parts anyway.

[SRE30]

Found a motorcycle I want today.

It's yours for 3k

[RoscoYoungno13]

anyone pick this up yet?

[SRE30]

nope still sitting in the garage

[PROJECTRB240SX]

3k for the block?

[SRE30]

and the transmission with cryotreated gears.

plus shipping

[SRE30]

3k for the block?


just to confirm.

this is for the longblock. including the top end of the motor.


just wanted to make sure you didn't think the sale was for the bare short block.

[SRE30]

Finally got around to putting it on ebay

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&rd=1,1&item=8033557854&sspagename=STRK%3AMESE%3AIT