vinhisbored
11-27-2005, 11:10 PM
Hey guys I'm nearing completion for the KA-T project.. I've spend a good deal on money with all the parts, and now what's left is the custom things.. first of all.. for those that would like to know the setup, here it is:
Total spent - $4318
Garrett t3/t04e 70 trim compressor, .63 A/R - $500
(To make it work you just need to exchange the flange
(and have the port for the internal gate on the compressor welded)
kineticmotorsport.com 24x12x3.5 bar & plate FMIC with hot wire Z32 MAF - $340
(3" cold side, 2.5" hot)
GReddy 38mm wastegate - $300
Enthalpy ROM Tune - 550cc injectors, Z32 maf, speed cut removed, etc.. - $600
HKS SSQBOV - $150
Deashwerks injectors (550cc) - $273
Apexi Boost Gauge - $125
Walbro fuel pump - $100
Apexi Turbo Timer and harness - $93
GReddy Oil Catch Can - $90
Rev Hard Manifold + turbo elbow - $355
Odyssey battery + relocation parts - $126.50
HKS SSQ + T3 downpipe flange - $60
4 more couplers + 8 t-bolt clamps - $50
T3 flange gasket set (manifold & fittings) - $6
2 flanges, oil tee, and the lines (from Jeff240sx) - $171.50
SPL SS braided clutch line/clutch fork pivot - $53
RPS Max Street Puck Clutch Kit - $430
Nismo Slave Cylinder - $175
Apexi Power Intake - $120
38mm Wastegate Flange + 2 gaskets - $20
Please refrain from commenting about the prices.. I know I've spend ALOT.. I could have had taken many different routes and saved money, but it's too late, and I'm not looking back.
Anyways, I'm planning on doing the whole blow-through setup and run the z32 maf on the cold side behind the bov. I would also need a custom turbo elbow to a SR downpipe/test pipe combo. Last would be the oil bung weld on the oil pan.. then the install.
My question is this.. do you guys know any shops that have good prices with quality? I'd rather not take it to a muffler shop. My buddy has a cousin that was going to do it.. just some little shop, but then I heard it's closing, so too late for that. I'm located in Perris, CA.. (951 area code) and I'm willing to travel maybe 2 hours max to have my stuff made and installed.
I got a quote from G-Dimensions, and the guy said everything would be $1200 at 'at discounted price' and that regular price was $1500. I believe that is wayyy over my budget. So please feel free to add or suggest something. Thanks alot guys!
Total spent - $4318
Garrett t3/t04e 70 trim compressor, .63 A/R - $500
(To make it work you just need to exchange the flange
(and have the port for the internal gate on the compressor welded)
kineticmotorsport.com 24x12x3.5 bar & plate FMIC with hot wire Z32 MAF - $340
(3" cold side, 2.5" hot)
GReddy 38mm wastegate - $300
Enthalpy ROM Tune - 550cc injectors, Z32 maf, speed cut removed, etc.. - $600
HKS SSQBOV - $150
Deashwerks injectors (550cc) - $273
Apexi Boost Gauge - $125
Walbro fuel pump - $100
Apexi Turbo Timer and harness - $93
GReddy Oil Catch Can - $90
Rev Hard Manifold + turbo elbow - $355
Odyssey battery + relocation parts - $126.50
HKS SSQ + T3 downpipe flange - $60
4 more couplers + 8 t-bolt clamps - $50
T3 flange gasket set (manifold & fittings) - $6
2 flanges, oil tee, and the lines (from Jeff240sx) - $171.50
SPL SS braided clutch line/clutch fork pivot - $53
RPS Max Street Puck Clutch Kit - $430
Nismo Slave Cylinder - $175
Apexi Power Intake - $120
38mm Wastegate Flange + 2 gaskets - $20
Please refrain from commenting about the prices.. I know I've spend ALOT.. I could have had taken many different routes and saved money, but it's too late, and I'm not looking back.
Anyways, I'm planning on doing the whole blow-through setup and run the z32 maf on the cold side behind the bov. I would also need a custom turbo elbow to a SR downpipe/test pipe combo. Last would be the oil bung weld on the oil pan.. then the install.
My question is this.. do you guys know any shops that have good prices with quality? I'd rather not take it to a muffler shop. My buddy has a cousin that was going to do it.. just some little shop, but then I heard it's closing, so too late for that. I'm located in Perris, CA.. (951 area code) and I'm willing to travel maybe 2 hours max to have my stuff made and installed.
I got a quote from G-Dimensions, and the guy said everything would be $1200 at 'at discounted price' and that regular price was $1500. I believe that is wayyy over my budget. So please feel free to add or suggest something. Thanks alot guys!