JDM parts craziely being sold! check it out!

[weei2]

hey, i got some JDM used parts that i have acquired from my brother but i dont need them so, its up for grabs for anyone here!

ok, lets start!

1. Pair of JDM (180sx) Aero side skirts, made of polyurethane, very strong and also lightweight =D Metallic Blue in color and Installation Hardware is NOT included. Item has some minor scratches. but its in MINT Condition!!

Looking to get $175 SOLD!

2. JDM (All S13) Trust old school strut bar, bar is made out of aluminum and round , and the ends are blue in color. there are only minor scratches, still straight and holds your car like a champ! again, its in MINT Condition!

Looking to get $45

3. JDM (All S13) JIC SF-1 ( Front Set Only ) it has Camber Plates and not dampening adjustable. Condition is BLOWN, i will sell it as a whole or parted out.
- Pair of the whole blown coilover kit, can be rebuilt by JIC USA , if i sell it as the whole thing, i would like to get $100
- Pair of Camber plates only will be sold for $80
- Pair of Springs, Rate = 7 kg. $20

4. Z32TT and R33 Front set up Brakes, spec: 5-lugs, 30mm Aluminum Calipers, and Used Rotors, MINT Condition!

The 4-luggers can also buy this and redrill the rotors to 4x114.3 set up and just get the conversion brake lines and you're good to go!

each set is $255

pictures will be available tomorrow and if you are interested, im in So CaL area, close to LA, please let me know at 626-274-4512 ask for Ryan or AIM at ch1ngo0 or email : weei_weei at yahoo.com

[weei2]

i can also provide the conversion brake lines for $85 if you need them.

[s13silady]

damn... i was just in LA yesterday.. if i ready this post i wouldve picked up those side for sure... any chance of you being in norcal anytime soon??

[weei2]

lol, sorry i wont go up there for a long time..but PICS will be up by tonight....thanks,...

[cfinch]

is the strut bar for the front or rear? Ill pick up those 180sx sides... $175 sounds cool. I'm in socal and can be in rowland heights prolly tommorow since I have to go down that way anyways tommorow. You have any contact info or actually Ill just pm you mine...

[IAM_SO_sLOw]

is it SS conversion lines? for front and rear?

[speedgod^s13]

Interested in the strut bar. How much shipped to 96816? Also is it for the front or rear?

[weei2]

-cfinch, i will call you as soon as i can about those skirts
-IAM SO sLow, the SS conversion lines are for the front set only and for the pair, cost $85
-speedgod^S13, The strut bar is for the Front. and i will give you the quote ASAP

thanks

[weei2]

here is some pix

http://www.lineupgarage.com/Pictures/skirts.jpg
and
http://www.lineupgarage.com/Pictures/skirts2.jpg

[wutangben]

I am interested in the sideskirts and the strut bar. can you post pics of the strut bar? also, if the skirts aren't sold, how much shipped to 60191 (business address)

Ben
[email protected]

[weei2]

heres some For the strut bar..

http://www.lineupgarage.com/Pictures/STB.jpg
http://www.lineupgarage.com/Pictures/oneend.jpg
http://www.lineupgarage.com/Pictures/otherend.jpg
http://www.lineupgarage.com/Pictures/bar.jpg

[weei2]

and the rest of the pix, ill post it tomorrow..
thanks..

[ryan hagen]

interested in the coils, how much for the pair complete, and did jic give you a quote for rebuilding?

[weei2]

yes, i think the quote was like $150 but i got a new set of cusco ones, thats y i sell this one..and for the full set, im letting it go for $100, worth it! the camber plates itself worth that much...

here are some pix:
http://www.lineupgarage.com/Pictures/jics.jpg
http://www.lineupgarage.com/Pictures/camberplates.jpg

springs will be there, but they were being cleaned up..

BTW, Sideskirts have been SOLD

[ryan hagen]

you have springs(7kg)? and the height adjusting nut/perches? i f you have every thing for them i think i ll get them lmk

[weei2]

ryan hagen, I just PMed you!

here are the pics of the brakes..

- 1 of the Z32 Brakes have S14 hubs and spindles, and it is 30mm Iron Cast calipers, comes with a used slotted/cross drilled rotors, and JDM aftermarket pads and im asking for $275 pick up for these:

http://www.lineupgarage.com/Pictures/zbrakes1.jpg
http://www.lineupgarage.com/Pictures/zbrakes2.jpg

- here is also the R33 Brakes pictures, it is 30mm aluminum calipers and somes with the original R33 hubs and spindles and is also a bolt on to 240s just like Z32 brakes.
im asking $255 for these:

http://www.lineupgarage.com/Pictures/r33brakes1.jpg
http://www.lineupgarage.com/Pictures/r33brakes2.jpg

i also still got some of the regular 30mm Aluminum Z32 brakes front set up in hand and is that clean

please let me know...

[weei2]

ok guys, some of the stuff have been sold and here are the ones that i still have:

1. JDM (All S13) Trust old school strut bar, bar is made out of aluminum and round , and the ends are blue in color. there are only minor scratches, still straight and holds your car like a champ! again, its in MINT Condition!

Looking to get $45

2. JDM (All S13) JIC SF-1 ( Front Set Only ) it has Camber Plates and not dampening adjustable. Condition is BLOWN, i will sell it as a whole or parted out.
- Pair of the whole blown coilover kit, can be rebuilt by JIC USA , if i sell it as the whole thing, i would like to get $100
- Pair of Camber plates only will be sold for $80
- Pair of Springs, Rate = 7 kg. $20

4. Z32TT and R33 Front set up Brakes, spec: 5-lugs, 30mm Aluminum Calipers, and Used Rotors, MINT Condition!

each set is $255

i currently have only the front set ups of ( 2 sets of Z32 Alum. cast brakes ) and ( 2 sets of R33 Alum. cast brakes )

IMHO, the R33 looks nicer than the 300zx and makes your car looks different!

come on! its up for grabs!

[TRUSE-R]

PM has been sent!

[Kreukishot]

If you're willing to part out the brakes let me know. I'm interested in the calipers only (prices please for z32 and r33?) I'm local and will pick up.

Thanks,
Chris

[s13drift240sx]

yea how much for calipers only

[s13drift240sx]

yea how much for calipers only get back to me at [email protected] thanks Surgeo

[s13silady]

how much for the strut shipped to 95131

[weei2]

if you want, i can...hmm....how about calipers only for $255?
thats why its better to get the whole thing? =D

[weei2]

s13silady, do you mean the strut bar or the strut for the coil overs?

truse-r, PM has been sent to you

[s13silady]

strut bar sorry

[weei2]

hey, S13silady, the strut is $53 shipped for you

[AzNCmB]

thos calipers look like the iron ones to me... correct me of i'm wrong...

[weei2]

as i have stated, those pictures are the iron ones, but just to show how clean it is...so dont refer to that picture for an actual item. the purpose of that picture is to show the cleanliness of my products!

FYI,
- Camber Plates are SOLD!
- Silvia Badges are SOLD!