JapaneseAutox
07-24-2019, 08:10 PM
Getting married. Motivated seller. Everything must go
Complete sr20det blacktop swap (Engine is on engine stand)
-Freshly decked head, Honed and hot tanked block. Head was leak tested and had a few valves and guides replaced. New 1.5mm Apex Headgasket, BC titanium retainers, Greddy valve springs, Greddy rocker arm stoppers, ARP Headstuds, Bunch of new gaskets, Baker Precision Stainless Turbo Lines, Greddy Oil Pan, Replaced Nissan factory oil pump (1.5k miles), New factory rings, New rear seal, ISIS Short Shifter, SR20 tranny (no grinds), Exedy Stage 2 Sprung 3-puck clutch (have two. One has more meat than the other. Can give you both).
Will come with: modded wiring harness, Megan turbo manifold, Megan(?) turbo Outlet, turbo has a new adjustable actuator, Aftermarket Exhaust (Believe it’s BEE-R), HKS Downpipe (dented from being too low), Fun mid-dump pipe, FMIC with piping, Stock blacktop ECU, a couple hentai VHS tapes + probably a bunch of other stuff I forgot to add - ENTERTAINING OFFERS FOR COMPLETE SWAP. (Will update with photos. Please DM for offers)
^^Will most likely put together to start up and compression test for a higher price when I find the time in a couple months. You can take it off my hands for less if the price is right. Weddings are expensive. Warn your friends. Can sell as a complete package with extra blocks for anyone looking to start hoarding.
4 x SR20DET Blocks
Block 068090W - Clean cylinders, No Crank - Only need slight hone - $250
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4286_20.jpg
Cylinder 1
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4287_20.jpgCylinder 2
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4289_20.jpgCylinder 3
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4290_20.jpgCylinder 4
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4291_20.jpg
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4294_20.jpg
Block 038964W - Replaced factory oil pump (2k miles), replaced rear seal, crank included, pitting exhaust side (Can get by with slight deck and will need bore). All bearings were fine but I recommend replacing them if you’re building - $350
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4295_20.jpg
Cylinder 1
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4306_20.jpg
Cylinder 2
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4305_20.jpg
Cylinder 3
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4304_20.jpg
Cylinder 4
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4303_20.jpg
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4308_20.jpg
Block 218678W - Chain Guides & Crank included, heavy pitting exhaust side (Re sleeve candidate. Possibly can get by with deck) - $250
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4309_20.jpg
Cylinder 1
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4314_20.jpg
Cylinder 2
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4313_20.jpg
Cylinder 3
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4312_20.jpg
Cylinder 4
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4311_20.jpghttps://i18.photobucket.com/albums/b141/Superxkyle/IMG_4315_20.jpg
Block 021143W - Chain Guides & Crank included, heavy pitting exhaust side (Re sleeve candidate. Deck won’t do) - $200
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4317_20.jpg
Cylinder 1
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4323_20.jpg
Cylinder 2
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4322_20.jpg
Cylinder 3
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4321_20.jpg
Cylinder 4
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4320_20.jpg
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4324_1_20.jpg
215/47/17 Federal RSR Tires - Brand New $180
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4236_2_20.jpg
4 x Hotwheels 17x9 +0. Good for drift spares - $200
-3 wheels need a polish. 1 is fine. (Will update with photos)
S13 coupe front and rear bumper. Shark nose - $40 both
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4243_20.jpg
S13 front and rear bumper support - $40 both
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4237_20.jpg
S13 coupe 50mm rear over fender (black) - $110
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4239_20.jpg
S13 Black Interior - $100
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4262_20.jpg
S13 coupe 30mm rear over fenders (good condition. Purple, Still on car)- $150
https://i18.photobucket.com/albums/b141/Superxkyle/Webp.net-resizeimage%20copy.jpg
https://i18.photobucket.com/albums/b141/Superxkyle/Webp.net-resizeimage.jpg
Very very clean s13 popup Vertex copy front bumper. It fits so well we believe it may be the original used to make the copies. Painted then never used. (Also Purple). - $200
S13 Manual mirrors (small part of tab missing, no mirror itself) - $20
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4266_20.jpg
Complete sr20det blacktop swap (Engine is on engine stand)
-Freshly decked head, Honed and hot tanked block. Head was leak tested and had a few valves and guides replaced. New 1.5mm Apex Headgasket, BC titanium retainers, Greddy valve springs, Greddy rocker arm stoppers, ARP Headstuds, Bunch of new gaskets, Baker Precision Stainless Turbo Lines, Greddy Oil Pan, Replaced Nissan factory oil pump (1.5k miles), New factory rings, New rear seal, ISIS Short Shifter, SR20 tranny (no grinds), Exedy Stage 2 Sprung 3-puck clutch (have two. One has more meat than the other. Can give you both).
Will come with: modded wiring harness, Megan turbo manifold, Megan(?) turbo Outlet, turbo has a new adjustable actuator, Aftermarket Exhaust (Believe it’s BEE-R), HKS Downpipe (dented from being too low), Fun mid-dump pipe, FMIC with piping, Stock blacktop ECU, a couple hentai VHS tapes + probably a bunch of other stuff I forgot to add - ENTERTAINING OFFERS FOR COMPLETE SWAP. (Will update with photos. Please DM for offers)
^^Will most likely put together to start up and compression test for a higher price when I find the time in a couple months. You can take it off my hands for less if the price is right. Weddings are expensive. Warn your friends. Can sell as a complete package with extra blocks for anyone looking to start hoarding.
4 x SR20DET Blocks
Block 068090W - Clean cylinders, No Crank - Only need slight hone - $250
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4286_20.jpg
Cylinder 1
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4287_20.jpgCylinder 2
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4289_20.jpgCylinder 3
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4290_20.jpgCylinder 4
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4291_20.jpg
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4294_20.jpg
Block 038964W - Replaced factory oil pump (2k miles), replaced rear seal, crank included, pitting exhaust side (Can get by with slight deck and will need bore). All bearings were fine but I recommend replacing them if you’re building - $350
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4295_20.jpg
Cylinder 1
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4306_20.jpg
Cylinder 2
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4305_20.jpg
Cylinder 3
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4304_20.jpg
Cylinder 4
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4303_20.jpg
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4308_20.jpg
Block 218678W - Chain Guides & Crank included, heavy pitting exhaust side (Re sleeve candidate. Possibly can get by with deck) - $250
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4309_20.jpg
Cylinder 1
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4314_20.jpg
Cylinder 2
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4313_20.jpg
Cylinder 3
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4312_20.jpg
Cylinder 4
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4311_20.jpghttps://i18.photobucket.com/albums/b141/Superxkyle/IMG_4315_20.jpg
Block 021143W - Chain Guides & Crank included, heavy pitting exhaust side (Re sleeve candidate. Deck won’t do) - $200
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4317_20.jpg
Cylinder 1
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4323_20.jpg
Cylinder 2
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4322_20.jpg
Cylinder 3
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4321_20.jpg
Cylinder 4
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4320_20.jpg
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4324_1_20.jpg
215/47/17 Federal RSR Tires - Brand New $180
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4236_2_20.jpg
4 x Hotwheels 17x9 +0. Good for drift spares - $200
-3 wheels need a polish. 1 is fine. (Will update with photos)
S13 coupe front and rear bumper. Shark nose - $40 both
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4243_20.jpg
S13 front and rear bumper support - $40 both
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4237_20.jpg
S13 coupe 50mm rear over fender (black) - $110
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4239_20.jpg
S13 Black Interior - $100
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4262_20.jpg
S13 coupe 30mm rear over fenders (good condition. Purple, Still on car)- $150
https://i18.photobucket.com/albums/b141/Superxkyle/Webp.net-resizeimage%20copy.jpg
https://i18.photobucket.com/albums/b141/Superxkyle/Webp.net-resizeimage.jpg
Very very clean s13 popup Vertex copy front bumper. It fits so well we believe it may be the original used to make the copies. Painted then never used. (Also Purple). - $200
S13 Manual mirrors (small part of tab missing, no mirror itself) - $20
https://i18.photobucket.com/albums/b141/Superxkyle/IMG_4266_20.jpg