TurboDaytona
05-12-2018, 11:36 AM
Built KA24DE
Supertech pistons 89.5mm Ring gap set at machine shop.
Eagle rods
OEM Nissan bearings – match to block and crank
Crankshaft polished – standard size
Complete rotating assembly balanced.
Xcessive motorsports windage tray/crank scraper
New OEM Nissan oil pump
Total $ wasted on engine $1600+
Engine was assembled by my. All clearances were checked with plasti-gauge, and all fasteners torqued to OEM spec, backed off, and re-torqued back to OEM spec. All parts were wiped with coffee filters before installation. (Way better than any towel, paper or otherwise. Coffee filters leave zero lint. Google it.) Crankshaft oil holes flushed and pipe cleaners ran though. Block was painted with engine primer and aluminum color paint. Deck machined for MLS headgasket. The check ball behind the oil filter housing has been replaced.
0 miles
Asking $1200
6-7 quart oil pan with tomei trap doors for kickouts (see pics) - $125 SOLD
T25 flanged bottom mount turbo manifold no cracks (used) $50
T3 cast top mount turbo manifold $50
One piece turbo outlet pipe (j-pipe) and downpipe with built in flex (fits great and less chance for leaks) $120
Tomei Headgasket (new) Sold
Brian crower 264 Cams (Used) $SOLD
JWT adjustable cam gears (new) $SOLD
ARP head studs (used) $SOLD!
Ported S13 head with Brian crower springs/titanium retainers/valves, Fresh machine work never installed. Machined for MLS headgasket. $SOLD
ACT 250 clutch/pressure plate 250mm (White Bunny setup) with (non-act) flywheel. This assembly I had balanced by the machine shop. Will hold over 500ft/lbs tq. Clutch disk is Solid 4 puck (I wanted quicker shifting. Less clutch disk mass figured) NEW (flywheel used, resurfaced) $SOLD
ATI super damper (new) $SOLD
S13 steel one piece driveshaft ABS $OLD
S13 non-abs manual driveshaft. $50
S13 5spd Transmission $100
S13 Valve cover powder coated black $40
850CC injectors - I dont remember what brand, but I think they are DW - SOLD!
S13 ka24de Nistune ECU with Consult cable - $300
****JUST ADDED*****
S14 shift boot with trim $20 shipped
Lower shift boot with ring - $20 shipped
S13 Custom middle mount intercooler setup. Clears headlight motors. Comes with Turbo XS RFL BOV - $250
New set of Engine/ trans mounts KA/SR - $50
Peak performance solid transmission mount - $40 shipped <Lower price!
KA intake manifold - Butterfly valves removed. Sold
Prices are without shipping unless otherwise specified.
Here is the link to my Google drive folder with all the pictures. I will be adding more pictures as I start organizing my garage.
https://drive.google.com/open?id=10x-Txl_wbKJ8AHj0YuL0qkiXgKH01Etm
If you buy several items, I will work out a discount. Also open to offers.
Supertech pistons 89.5mm Ring gap set at machine shop.
Eagle rods
OEM Nissan bearings – match to block and crank
Crankshaft polished – standard size
Complete rotating assembly balanced.
Xcessive motorsports windage tray/crank scraper
New OEM Nissan oil pump
Total $ wasted on engine $1600+
Engine was assembled by my. All clearances were checked with plasti-gauge, and all fasteners torqued to OEM spec, backed off, and re-torqued back to OEM spec. All parts were wiped with coffee filters before installation. (Way better than any towel, paper or otherwise. Coffee filters leave zero lint. Google it.) Crankshaft oil holes flushed and pipe cleaners ran though. Block was painted with engine primer and aluminum color paint. Deck machined for MLS headgasket. The check ball behind the oil filter housing has been replaced.
0 miles
Asking $1200
6-7 quart oil pan with tomei trap doors for kickouts (see pics) - $125 SOLD
T25 flanged bottom mount turbo manifold no cracks (used) $50
T3 cast top mount turbo manifold $50
One piece turbo outlet pipe (j-pipe) and downpipe with built in flex (fits great and less chance for leaks) $120
Tomei Headgasket (new) Sold
Brian crower 264 Cams (Used) $SOLD
JWT adjustable cam gears (new) $SOLD
ARP head studs (used) $SOLD!
Ported S13 head with Brian crower springs/titanium retainers/valves, Fresh machine work never installed. Machined for MLS headgasket. $SOLD
ACT 250 clutch/pressure plate 250mm (White Bunny setup) with (non-act) flywheel. This assembly I had balanced by the machine shop. Will hold over 500ft/lbs tq. Clutch disk is Solid 4 puck (I wanted quicker shifting. Less clutch disk mass figured) NEW (flywheel used, resurfaced) $SOLD
ATI super damper (new) $SOLD
S13 steel one piece driveshaft ABS $OLD
S13 non-abs manual driveshaft. $50
S13 5spd Transmission $100
S13 Valve cover powder coated black $40
850CC injectors - I dont remember what brand, but I think they are DW - SOLD!
S13 ka24de Nistune ECU with Consult cable - $300
****JUST ADDED*****
S14 shift boot with trim $20 shipped
Lower shift boot with ring - $20 shipped
S13 Custom middle mount intercooler setup. Clears headlight motors. Comes with Turbo XS RFL BOV - $250
New set of Engine/ trans mounts KA/SR - $50
Peak performance solid transmission mount - $40 shipped <Lower price!
KA intake manifold - Butterfly valves removed. Sold
Prices are without shipping unless otherwise specified.
Here is the link to my Google drive folder with all the pictures. I will be adding more pictures as I start organizing my garage.
https://drive.google.com/open?id=10x-Txl_wbKJ8AHj0YuL0qkiXgKH01Etm
If you buy several items, I will work out a discount. Also open to offers.