pat1
09-18-2017, 05:10 PM
http://https://photos.google.com/album/AF1QipPpuZjTebYdHD_ty70aMBVdhF0tXX_PYmUFCg6X/photo/AF1QipMOOdOttmFI_d31XMAzQ1evMLJcwiAbn9Nxrf501976 Datsun 280z
1JZGTE swap
Single Precision PT-61 turbo
HKS 264/272 cams
550 injectors
Stinger EMS standalone
Stage 2 Clutch
Custom engine cradle and motor mounts and trans mount
3 inch SS exhaust,3 inch down pipe
Tuned by Turbo Dave
4inch intercooler
PRC radiator
Tial Wastegate
Tial Blow off valve
Aeromotive fuel pressure regulator
Dynoed @446 hp @16psi
Nissan Motorsprots LSD 3.9 ratio diff
Z31 axles and MM flanges
R154 trans
Wilwood front 12.2 inch rotors 4 piston calipers and rear brakes 12.2 inch rotors 4 piston calipers from Arizona Z car
Wilwood proportioning valve
280zx brake booster
15/16 master cylinder
Steel braided brake lines
Suspension Techniques sway bars
New ball joints
New tie rods
Ground control coil over 225lbs front and 250lbs rear springs
Front and rear strut tubes have been sectioned struts
Tokico 5 way struts front and rear
Autometer gauges
Blitz boost controller
Aeromotive Stealth Fuel cell
New frame rails
New floor pans
There is probably more that I'm forgetting
I've owned this 280z since 1994.
This has been my project for many years and I have had a lot of fun with it but it's time for another project.
I don't have to sell this and I'm not in a hurry too. I built every bit of this car. I am a ASE master/ Mazda master tech and this
car is built RIGHT, No slap together crap here.
I'm looking to get $17,000 or best offer. I'm up for trades
1JZGTE swap
Single Precision PT-61 turbo
HKS 264/272 cams
550 injectors
Stinger EMS standalone
Stage 2 Clutch
Custom engine cradle and motor mounts and trans mount
3 inch SS exhaust,3 inch down pipe
Tuned by Turbo Dave
4inch intercooler
PRC radiator
Tial Wastegate
Tial Blow off valve
Aeromotive fuel pressure regulator
Dynoed @446 hp @16psi
Nissan Motorsprots LSD 3.9 ratio diff
Z31 axles and MM flanges
R154 trans
Wilwood front 12.2 inch rotors 4 piston calipers and rear brakes 12.2 inch rotors 4 piston calipers from Arizona Z car
Wilwood proportioning valve
280zx brake booster
15/16 master cylinder
Steel braided brake lines
Suspension Techniques sway bars
New ball joints
New tie rods
Ground control coil over 225lbs front and 250lbs rear springs
Front and rear strut tubes have been sectioned struts
Tokico 5 way struts front and rear
Autometer gauges
Blitz boost controller
Aeromotive Stealth Fuel cell
New frame rails
New floor pans
There is probably more that I'm forgetting
I've owned this 280z since 1994.
This has been my project for many years and I have had a lot of fun with it but it's time for another project.
I don't have to sell this and I'm not in a hurry too. I built every bit of this car. I am a ASE master/ Mazda master tech and this
car is built RIGHT, No slap together crap here.
I'm looking to get $17,000 or best offer. I'm up for trades