PDA

View Full Version : 5 DAY ONLY HOLIDAY CHRISTMAS SPECIAL Chrome TC Rods/Rucas/Toe arms from $109.95 +free


CPARKPowertrix
10-12-2004, 10:38 AM
FOR This LIMITED TIME ONLY- OUR 5 DAY CHRISTMAS SPECIAL will start today December 21st and end on Sunday December 26th. Take advangage of these great savings.

**ADDED BONUS: Get FREE urethane bushings for each set of arms (Tie rod boots, toe arm bushings, rear camber arm bushings)** see our bushings post for pics and value. (up to $40.00 in FREE Bushings) http://www.zilvia.net/f/showthread.php?t=64365

Purchase Tension rods get FREE Tie rod boots
Purchase Toe connecting rods get FREE Toe connecting rods bushings
Purchase Rear camber arms get FREE Rear camber arms bushings

ALL NEW S13/S14 Chrome Finish Suspension arms Tension rods/RUCA/TOE connecting rods.

Our new tension rods now have a extended shaft design for additional adjustment for the S14. Our NEW Chromium finish was chosen specifically due to our experiences with durability with power coating. This new finish is much stronger and won’t chip and rust as easily as the previous powder coated versions.

***5 DAY CHRISTMAS 2004 SPECIAL PRICING ***
New Chrome S13/S14 Tension rods $109.95 (IN STOCK)
New Chrome S13 Rear dual camber arms $129.95 (IN STOCK) Reg. $169.00
New Chrome S14 Rear single camber arms $129.95 (IN STOCK Reg. $169.00
New Chrome S13/S14 Toe connecting rods $129.95 (IN STOCK) Reg. $169.00

http://www.powertrix.com/S14TCrodshaftthumb.jpg (http://www.powertrix.com/S14TCrodshaft.JPG) http://www.powertrix.com/chromeTCrodsthumb.jpg (http://www.powertrix.com/chromeTCrods.JPG)
http://www.powertrix.com/S14CMRUCAthumb.jpg (http://www.powertrix.com/S14CMRUCA.JPG) http://www.powertrix.com/S14CMTOEthumb.jpg (http://www.powertrix.com/S14CMTOE.JPG)
http://www.powertrix.com/z32s13RUCAthumb.jpg (http://www.powertrix.com/z32s13RUCA.JPG)

TENSION RODS/REAR CAMBER ARMS/TRACTION CONTROL ARMS:
The following Powertrix products (tension rods, camber arms, toe connecting rods, and traction control arms) are made of heat tempered forged steel. There are many inferior copies on the market made of aluminum that are not as strong and are prone to bend and flex. These suspension components under go massive stress and entire weight transfer of the vehicle. A daily driven or street car is subjected to even more blunt or shock force due to street hazards and road conditions there fore we do not recommend the use of aluminum for these components. Our components have been on many vehicles for over 3 years and have been tested on several even heavier vehicles such as Nissan Z32s with a perfect track record. Also, our components have been Drag and Track tested at California Speedway (Fontana) and the road courses of Willow Springs under the most rigorous scenarios, with several different adjustments and are used and trusted by the other major Nissan specific companies for their personal and race prepped vehicles.

ORDERING AND PAYMENT DETAILS:

Please email me:

Name
Shipping address (for shipping quote)
Contact Number
Components wanted

Paypal payments:
If using a Credit card through Paypal use [email protected] Please add 2.9% for Paypal fees.

If transferring from Paypal to Paypal account use [email protected] (NOTE: This account will not accept Credit Card Payments.)

Or you can send a money order to:

POWERTRIX
Attn: Charles Park
9450 Mira Mesa Blvd # B 447
San Diego CA 92126

Please inform me if you are sending payment by mail and send it by means that are track able for your own protection. Example: any shipping company that will provide you with a tracking number or delivery confirmation.

Please feel free to call me or email me at [email protected] with any questions you may have.

Neejay
10-13-2004, 01:51 AM
"This new finish is much stronger and won’t chip and rust as easily as the previous powder coated versions."

The powder coated versions have problems with rust?

Can I get a shipping quote on the s13/s14 powder coated ruca?

30273 Rex, GA

Thanks.

CPARKPowertrix
10-13-2004, 09:02 AM
"This new finish is much stronger and won’t chip and rust as easily as the previous powder coated versions."

The powder coated versions have problems with rust?

Can I get a shipping quote on the s13/s14 powder coated ruca?

30273 Rex, GA

Thanks.

Hello,

The powder coating is much softer than the chrome finish. When the powder coating comes off, it exposes bare metal and it is at these points where the bare metal tends to rust. they can be sanded down as repainted but is a bit of a hassle as on most of the arms, the adjustment points (that are powder coated) almost immediately start to flake and chip once you put a wrench on them. This does not degrade the integrity of the arms but they look a bit messy once the powder coat starts to come off. Obviously, if rust is left for an extended period of time, if could eventually weaken the properties of the metal. Though we haven't actually had a total failure in a component due to rust, we had taken the proactive approach at offering a better product both in asthetics and quality.

Heartwork
10-16-2004, 03:17 AM
i just received my toe and traction rods and power brace!!!
FAAAAAAAAAST shipping and Charles is an excellent person to deal with....

now onto the parts.....Amazing quality! the weld seams are very precise and the Chrome finish is sweeeet.....pricing on these are excellent also, compared to "JDM" brands that cost 3 times as much, i assure these compare equally.....Compared to my Kazama, Cusco, and Tein products currently on my car, Powertrix parts is right on par

i have yet to actually test them out yet, but will soon :)

1 88 U
10-17-2004, 11:24 PM
when will the chrome finished s13 rods and arms be available?

VA240
10-18-2004, 04:52 PM
How do you grease the zerk fittings?

=]

-VA240

kabukie
10-18-2004, 05:59 PM
Can i call in an order with a credit card payment?

CPARKPowertrix
10-19-2004, 12:14 PM
when will the chrome finished s13 rods and arms be available?

The S13 Chrome Tension rods and Camber arms are NOW availible as well. Same pricing

S13 Chrome tension rods $149.00 shipped
S13 Chrome rear camber arms $149.00 shipped
S13 Chrome rear toe connecting rods $149.00 shipped

May of the S13 owners like to use the single armed RUCAs as it clears a suspension upgrades such as coil overs, etc. and they are lighter. We do have the dual armed RUCAs as well for $149.00 shipped Reg $169.00

XXX4life
10-19-2004, 12:21 PM
do you still have s13 front tension rods in the old finish?

CPARKPowertrix
10-19-2004, 12:48 PM
How do you grease the zerk fittings?

=]

-VA240

We are working on getting the right size grease gun fittings to lube the zerk fittings. Some of the guys have said they found fittings that work at NAPA auto parts store as they have taken the arms in and sized up the closest fitting possible. We have used a slightly oversized fitting to pump grease into the fitting and is seems to work just fine. (it is just a little bit messy as there is some overage that is easily cleaned off.)

http://www.streetneeds.com/uploads/auser/TCrodinstallthumb.jpg (http://www.streetneeds.com/uploads/auser/TCrodinstall.JPG)

Also: Tension rod INSTALLATION TIP:

Notice how the slant of the ball joints are on the tension rods - (Downward and toward the engine) please be sure when installing the tension rods that you follow this configuration. The reason is that once the car is set back down on the ground, the suspension readjusts and twists the ball joint in the opposite direction. The driver's side is the side you have to watch as once it is tighten; it has a tendency to swivel down and towards the wheel. (This is incorrect and can cause unnecessary stress on the ball joint leading to premature failure as it has no more motion to swivel once the car is set back down on the ground.)

CPARKPowertrix
10-19-2004, 12:50 PM
do you still have s13 front tension rods in the old finish?

Yes, We have a couple left over. However, supply is getting low as we are switching over to the all chrome finish.

CPARKPowertrix
10-19-2004, 12:53 PM
Can i call in an order with a credit card payment?

Unfortunately at this time, we can only take credit card through Paypal. If you like, I can email you a Paypal invoice and it will show you how to pay easily with your Credit Card. What is your Email address?

kabukie
10-19-2004, 02:28 PM
its [email protected]

KA24DESOneThree
10-21-2004, 02:33 PM
Since I live in San Diego county, could I just drop by and pay cash for some old-style S13 tension rods?

CPARKPowertrix
10-21-2004, 06:30 PM
Since I live in San Diego county, could I just drop by and pay cash for some old-style S13 tension rods?

Yes, give me a call and we'll arraige to get together. I'm out of town on Friday but will be back Saturday. I'll take a set home with me and We cam meet over the weekend. (619) 944-6055.

KA24DESOneThree
10-21-2004, 08:14 PM
Oh snap, that's sweet. I'll call within the next half-hour. My name's Steve.
*edit: Left a message. I neglected to leave a callback number, I always forget that my home phone is blocked from caller ID. If you can, gimme a call back at (760) 723-8484 up until about 10pm tonight and from 1:30-10pm tomorrow. Thanks much.*

DavidC
10-21-2004, 08:45 PM
the S13 Ruca's only come in the single arm configuration?

thanks

VA240
10-22-2004, 06:21 AM
We are working on getting the right size grease gun fittings to lube the zerks. Some of the guys have said they found fittings that work at NAPA auto parts store as they have taken the arms in and sived up the closest fitting possible. We have used a slightly oversized fitting to pump grease into the fitting and is seems to work just fine. (it is just a little bit messy as there is some overage that is easily cleaned off.)



Good post! I'm glad you're working on figuring this out.

-VA240
OK, it's time for me to start ordering some more parts with zerk fittings!

CPARKPowertrix
10-22-2004, 08:58 AM
the S13 Ruca's only come in the single arm configuration?

thanks

The S13 also comes in a dual arm configuration. They are $149.00 (Reg $169.00) Either single or dual arms work great. For S13 owners doing suspension mods, they prefer the single arm as it allows clearance for coilover kits and they are also lighter than the dual arm RUCAs for those who are wieght conscience.

http://www.powertrix.com/z32s13RUCAthumb.jpg (http://www.powertrix.com/z32s13RUCA.JPG)

CPARKPowertrix
11-09-2004, 01:07 PM
UPDATE: All components are back in stock. We expect to have the traction rods in the new chrome finish by December. We still have stock on the old finish products as well.

pkw1
11-09-2004, 10:07 PM
do you still have the tension rods for S14 in the old finish? Will you ship to Canada? shipping rate to Canada? what other suspension products do you have for S14?

thanks

SilviaDriver
11-09-2004, 10:24 PM
still going on correct? i think ima send in MO

CPARKPowertrix
11-10-2004, 12:46 PM
do you still have the tension rods for S14 in the old finish? Will you ship to Canada? shipping rate to Canada? what other suspension products do you have for S14?

thanks

Yes, we can ship to Canada. shipping is usually around $12.00-18.00 depending on shipping code. We carry all the various adjustable suspension arms, subframe spacers, bushings, front frame power brace and we are hoping to have our own line of coil over (adjustable strut and spring combination) kits availible next year. We also do the Z32 brake up grades as well. Here are links to our other specials:

http://www.zilvia.net/f/showthread.php?t=64365

http://www.zilvia.net/f/showthread.php?t=61077

Thanks.

CPARKPowertrix
11-10-2004, 12:48 PM
still going on correct? i think ima send in MO

Yes, The special is still going. Thanks.

DaConfusion
11-11-2004, 02:17 PM
I just got my S14 RUCA's and Bushings. Fast speed, beyond excellent packing. Very professional. Cant be happier, now if only I could get my coilovers from another seller and I will be set. Thanks!

pkw1
11-11-2004, 07:02 PM
Can you send me paypal invoice please for a set of S14 tension rods, shipped to Edmonton, Alberta, Canada T5Y 2L2

my paypal email is [email protected]

thanks

Yes, we can ship to Canada. shipping is usually around $12.00-18.00 depending on shipping code. We carry all the various adjustable suspension arms, subframe spacers, bushings, front frame power brace and we are hoping to have our own line of coil over (adjustable strut and spring combination) kits availible next year. We also do the Z32 brake up grades as well. Here are links to our other specials:

http://www.zilvia.net/f/showthread.php?t=64365

http://www.zilvia.net/f/showthread.php?t=61077

Thanks.

MrSkinny
11-24-2004, 12:45 PM
o man. for 10 bucks more i definittely wouldve gone for the chrome over the old finish.

WILDACEX187
11-24-2004, 12:53 PM
how much for a set of tc rods shipped to 11101?

SilviaDriver
11-24-2004, 04:03 PM
how much for...

New Chrome S13/S14 Tension rods $109.95
New Chrome S13/S14 Toe connecting rods $129.95

both of those shipped to 95119

DavidC
11-29-2004, 01:58 PM
so the tension rods should be slanted away from the motor?

We are working on getting the right size grease gun fittings to lube the zerks. Some of the guys have said they found fittings that work at NAPA auto parts store as they have taken the arms in and sived up the closest fitting possible. We have used a slightly oversized fitting to pump grease into the fitting and is seems to work just fine. (it is just a little bit messy as there is some overage that is easily cleaned off.)

http://www.streetneeds.com/uploads/auser/TCrodinstallthumb.jpg (http://www.streetneeds.com/uploads/auser/TCrodinstall.JPG)

Also: Tension rod INSTALLATION TIP:

Notice how the slant of the ball joints are on the tension rods - (Downward and toward the engine) Please be sure when installing the tension rods that you follow this configuration.The reason is that once the car is set back down on the ground, the suspension readjusts and twists the ball joint in the the opposite direction. The driver's side is the side you have to watch as once it is tighten, it has a tendancy to swivel down and towards the wheel. (this is incorrect and can cause unnecessary stress on the ball joint leading to premature failure as it has no more motion to swivel once the car is set back down on the ground.)

SilviaDriver
11-29-2004, 02:28 PM
FOR This LIMITED TIME only- OUR After Thanksgiving Special will start today November 29th and end on Friday June 3rd.


June 3rd or January 3rd?

aggiez32
11-30-2004, 07:21 PM
Are these the same as for the Z32? If so, you haven't posted these at $149 shipped on twinturbo.net, yet! I was going to order a set today but ran out of time.

I need a set by Friday so I can install my shocks/springs. If they're the same for the Z, how much to get them for shipped UPS Blue, total? You can email me [email protected]

Thanks Charles!

nocturnaldrifter
12-01-2004, 12:12 AM
I just purchased toe rods, camber arms, and traction control rods from charles. As well as new bushing and subframe spacers. All the suspension components look well made, canit wait to put them on. Just need to find somewhere where I can put on these goddamn bushing, anyone know of a place taht can do it without taking off the hub? Los Angeles area prefered.

khoadogg
12-01-2004, 02:46 AM
how much shipped for a set of TC rods for S13 to 92507?

Champster
12-02-2004, 05:52 PM
Whats the shipping on Camber and Toe Arms for my S14 to 80127?

kabukie
12-07-2004, 08:43 AM
Whats the adjustment of the Toe arms? Will it correct -2.5 of toe?
Thanks

WILDACEX187
12-08-2004, 12:25 AM
got my tc rods in the mail. look very good and very sturdy. cant wait to put them on. thanx :bow:

Champster
12-09-2004, 01:31 PM
Just got mine in an hour ago. Madd props to Charles. Great to do business with and will be again in the near future.

They are soo bling bling!

bing
12-10-2004, 06:53 PM
is your site going to be up soon?

there was some stuff i am interested in... will u be at the JGTC?

CPARKPowertrix
12-17-2004, 03:10 PM
is your site going to be up soon?

there was some stuff i am interested in... will u be at the JGTC?

Hopefully the web site will be up by the 1st of the year. We are still putting it together. YES I'll be at JGTC both on Saturday and Sunday. I'm bringing product for the guys who have asked me to bring stuff for them and I'll have some extra product with me as well. Let me knowif you are looking for something in particular and I'll bring that to if possible. I'll be parked in the in field with the rest of the Car Clubs. Thanks.

allblackS14
12-18-2004, 02:52 PM
Hey Charles are you guys any closer to finishing your coilovers?

NismoSilvia270R
12-18-2004, 06:25 PM
how long until self-lubricating pillowjoints?

CPARKPowertrix
12-22-2004, 12:20 PM
5 DAY ONLY HOLIDAY CHRISTMAS SPECIAL Chrome TC Rods/Rucas/Toe arms from $109.95 + free bushings

FOR This LIMITED TIME ONLY- OUR 5 DAY CHRISTMAS SPECIAL will start today December 21st and end on Sunday December 26th. Take advangage of these great savings.

**ADDED BONUS: Get Free urethane bushings for each set of arms purchased (Tie rod boots, toe arm bushings, rear camber arm bushings)** see our bushings post for pics and value. (up to $40.00 in FREE Bushings) http://www.zilvia.net/f/showthread.php?t=64365

Purchase Tension rods get FREE Tie rod boots
Purchase Toe connecting rods get FREE Toe connecting rods bushings
Purchase Rear camber arms get FREE Rear camber arms bushings

See original post for more details.

SlowCoupe
12-22-2004, 08:25 PM
S13 dual arm RUCA and free bushing-shipping quote to 70001 please and do you take personal checks?

SlowCoupe
12-24-2004, 11:28 AM
you have a pm Charles

black s13
12-25-2004, 03:58 PM
pm sent for toe rods :)

one_tyme
01-01-2005, 04:17 PM
here is my review on the products, as i got my shipemtn in last week. first off, communication was excellent. i sent payment on a sunday, and items (tension rod, traction, toe, ruca and power brace) were shipped out on monday and i got them on a wed.......and i live in hawaii.

when i got them i was suprised on the quality of the finish and workmanship. ive had expensive cusco and kazama parts, and these (to me) looked up to par. installation was easy and i am waiting to test these under extreme driving conditions, lol.

but overall nice product, fast shipment, excelent prices. i am very please with my purchase. thank yous!!

mooboy
01-02-2005, 11:12 PM
PM Sent for tension rods.

blu808
01-03-2005, 05:11 PM
pm sent please let me know.
I need 2 sets of s14 rucas
1 set of s14 tension rods.

Thanks

KingKong8247
01-03-2005, 08:03 PM
Question: How often should we grease the joints? And as NismoSilvia270R when are you coming out with self-lubricating joints?

boost infested
01-07-2005, 10:37 PM
Thanks Trix!!!

blu808
01-12-2005, 10:47 AM
Question: How often should we grease the joints? And as NismoSilvia270R when are you coming out with self-lubricating joints?

I would grease them every few thousand miles. You can also check by rotating the ball and if it feels sticky or makes any noise then grease it.

mooboy
01-12-2005, 02:51 PM
Got my items, and they work great. Thanks!

AcuraTechVa
01-18-2005, 11:55 AM
are tension rods still available?