DRIFTER-M
12-01-2016, 05:25 PM
Simply testing the waters on this part out, part list ahead.
I can pull and ship most anything, however the motor you will have to come start and pull yourself. Everything is the motor is included upon sale of motor, including the standalone ECU.
Motor set w/ trans ($6,500)
Motor:
In November of 2015 I purchased a blacktop SR, fully built by Redline Performance of Daytona Beach, FL. Redline Performance installed the motor. In January, I had the car tuned by Martin @ Enthalpy. It is currently at 1 BAR boost, running around 300HP dyno'd. Has about 2,000-3,000 miles on it since rebuild.
= New s14 notch top cylinder head
= Valve job
= Supertech seals
= Supertech bronze guides
= Bc dual valve springs
= Bc retainers
= Bc 272s
= Mazworx chain tensioner
= Coyes timing kit
= ARP headstuds Cosmetic gasket
= Block bored to 87mm
= Weisco 9:2:1
= Manley rods
= King race series rod crank & thrust washers
= Bnew crank cut .25 over for race series bearings
= One oil pump
= Oem lower oil pan
= Cometic intake gasket
= Cometic exhaust gasket
=Tomei oil filter adapter #8 lines to filter
=Tomei oil filter housing
= Braided oil feed to turbo
= Braided water lines turbo
= S14 water neck conversion
= Isis rad hoses
= Ebay rad
= T3 70/63
= Custom top mount
= 3in vband exhaust
= Turbonetics 38wastegate Custom dump pipe
= Braided oil return line
= 1000cc dechworks Aermotive a
= 1000 fpr ISR fpr adapter
=Braided lines to rail and fpr Nrg valve cover washers
= Freddy upper intake
= Delted iacv
= Welded fmic piping and ssqv
= ISR fmic T bolt clamps and couplers
=Fidanza flywheel
=Comp stage 4 Clutch (has around 1500 miles, almost brand new)
= ISR short throw
=Megan Solid Motor Mounts
= Cody ace bracket to s14 New ps pump
= Stinger standalone and custom harness tuned by Martin @ Enthalpy.
= No MAF
= 3.5 bar map sensor
= 2 Electric Fans and relays
= Full, working AC/ Heat
Since I don't offer any type of warranty and don't like selling a part so big without comfort from the buyer, I will not pull and ship. You come start, take a ride with me, and have to pull. I no longer have a hoist or lift either, so you will have to arrange for that to pull the motor and trans.
The rest of the parts list can be found here, but only will be sold of motor is sold:
http://zilvia.net/f/showthread.php?t=630648
Thank you!
http://i65.tinypic.com/2mxeszp.jpg
A video and more pictures available at the link^^
I can pull and ship most anything, however the motor you will have to come start and pull yourself. Everything is the motor is included upon sale of motor, including the standalone ECU.
Motor set w/ trans ($6,500)
Motor:
In November of 2015 I purchased a blacktop SR, fully built by Redline Performance of Daytona Beach, FL. Redline Performance installed the motor. In January, I had the car tuned by Martin @ Enthalpy. It is currently at 1 BAR boost, running around 300HP dyno'd. Has about 2,000-3,000 miles on it since rebuild.
= New s14 notch top cylinder head
= Valve job
= Supertech seals
= Supertech bronze guides
= Bc dual valve springs
= Bc retainers
= Bc 272s
= Mazworx chain tensioner
= Coyes timing kit
= ARP headstuds Cosmetic gasket
= Block bored to 87mm
= Weisco 9:2:1
= Manley rods
= King race series rod crank & thrust washers
= Bnew crank cut .25 over for race series bearings
= One oil pump
= Oem lower oil pan
= Cometic intake gasket
= Cometic exhaust gasket
=Tomei oil filter adapter #8 lines to filter
=Tomei oil filter housing
= Braided oil feed to turbo
= Braided water lines turbo
= S14 water neck conversion
= Isis rad hoses
= Ebay rad
= T3 70/63
= Custom top mount
= 3in vband exhaust
= Turbonetics 38wastegate Custom dump pipe
= Braided oil return line
= 1000cc dechworks Aermotive a
= 1000 fpr ISR fpr adapter
=Braided lines to rail and fpr Nrg valve cover washers
= Freddy upper intake
= Delted iacv
= Welded fmic piping and ssqv
= ISR fmic T bolt clamps and couplers
=Fidanza flywheel
=Comp stage 4 Clutch (has around 1500 miles, almost brand new)
= ISR short throw
=Megan Solid Motor Mounts
= Cody ace bracket to s14 New ps pump
= Stinger standalone and custom harness tuned by Martin @ Enthalpy.
= No MAF
= 3.5 bar map sensor
= 2 Electric Fans and relays
= Full, working AC/ Heat
Since I don't offer any type of warranty and don't like selling a part so big without comfort from the buyer, I will not pull and ship. You come start, take a ride with me, and have to pull. I no longer have a hoist or lift either, so you will have to arrange for that to pull the motor and trans.
The rest of the parts list can be found here, but only will be sold of motor is sold:
http://zilvia.net/f/showthread.php?t=630648
Thank you!
http://i65.tinypic.com/2mxeszp.jpg
A video and more pictures available at the link^^