oberkill
09-22-2004, 07:57 PM
Time for me to move on to a new project so I am selling the black car. The body is in OK shape but the front is "painted" flat black and the rest of the car is factory black. There are some dings but no dents. Interior is also in pretty goos shape with cloth seats from a S14. Tires are basically new as are the brake pads on the car. Has quite a few new stock parts not listed below as well, brake master cylinder, clutch master/slave cylinder, lower ball joints, etc (cant remember everything!!) Will also come with some spares, a spare transmission, etc. I am asking $12,000 OBO. Here are most of the specs, I will get it to the dyno soon and get a good dyno number. The last time I had it there without a few of the last pieces recently added (including the tuned ECU) it was at 287 at less than 1 bar but was out of fuel. Pics at the bottom though they are a few months old so not quite up to date:
Engine
- S13 SR20DET
- Tuned ECU
- JDM Stainless Manifold (unknown maker)
- GTiR T28 Turbo
- Greddy Turbo Outlet pipe
- HKS internal wastgate
- ER hotpipe
- JWT pop charger
- Greddy oil catch can
- Greddy oil filter relocation
- Summit fuel pressure gauge
- NISMO fuel pressure regulator
- Greddy R-SPL FMIC
- Greddy 3 in downpipe
- JIC 3in bullet exhaust
- 3 in cat replacement pipe
- all intercooler clamps replace with Summit T-clamps
- Morosso recirculating coolant catch can
- All rubber hose replaced with braided lines
- KOYO alum radiator
- Power enterprise upper and lower radiator hose
- Electric fan with electronic thermastat
Footworks
- SPEC stage 4 clutch
- braided clutch line (not installed)
- B&M short shifter
- Nismo leather shift knob
- Nismo power bar
- Kazama TC rods
- Tein inner and outer tie rod ends
- JSPEC front ladder bar
- CPOWERTRIX rear subframe spacers
- CPOWERTRIX front upper control arms
- CPOWERTRIX rear upper control arms
- Aluminum driveshaft
- JIC rear toe arms
- CPOWERTRIX RUCA's
- KAZ 1.5 way LSD
- NISMO rear diff cover
- Tein HR coilovers
- Tein front camber plates
- Cusco rear triangle strut tower bar
- 30mm Z32 front brake calipers/rotors w/ braided lines (not installed)
Interior
- S14 front seats
- Greddy white faced oil pressure gauge
- Greddy white faced boost gauge
- Greddy white faced water temp gauge
- White faced gauges for stock console
- Apexi S-AFC II
- JDM style two deck radio
Exterior
- Silvia conversion
- GTR grill
- Santeca HID kit (not installed)
- Rear 5 lug conversion
- Kosei K1 16x8.5 rear rims w/245 tires
- Buddy Club P1 16x7.5front rims w/225 tires
http://project240.com/pictures/240/cardone.jpg
http://project240.com/pictures/240/cardone2.jpg
http://project240.com/pictures/240/cardone3.jpg
http://project240.com/pictures/240/cardone4.jpg
http://project240.com/pictures/240/cardone7.jpg
Drop me a e-mail ([email protected]) or PM if you are interested. If you pay with a casiers check you will have to wait for it to clear before you can have the car.....
Alan
Engine
- S13 SR20DET
- Tuned ECU
- JDM Stainless Manifold (unknown maker)
- GTiR T28 Turbo
- Greddy Turbo Outlet pipe
- HKS internal wastgate
- ER hotpipe
- JWT pop charger
- Greddy oil catch can
- Greddy oil filter relocation
- Summit fuel pressure gauge
- NISMO fuel pressure regulator
- Greddy R-SPL FMIC
- Greddy 3 in downpipe
- JIC 3in bullet exhaust
- 3 in cat replacement pipe
- all intercooler clamps replace with Summit T-clamps
- Morosso recirculating coolant catch can
- All rubber hose replaced with braided lines
- KOYO alum radiator
- Power enterprise upper and lower radiator hose
- Electric fan with electronic thermastat
Footworks
- SPEC stage 4 clutch
- braided clutch line (not installed)
- B&M short shifter
- Nismo leather shift knob
- Nismo power bar
- Kazama TC rods
- Tein inner and outer tie rod ends
- JSPEC front ladder bar
- CPOWERTRIX rear subframe spacers
- CPOWERTRIX front upper control arms
- CPOWERTRIX rear upper control arms
- Aluminum driveshaft
- JIC rear toe arms
- CPOWERTRIX RUCA's
- KAZ 1.5 way LSD
- NISMO rear diff cover
- Tein HR coilovers
- Tein front camber plates
- Cusco rear triangle strut tower bar
- 30mm Z32 front brake calipers/rotors w/ braided lines (not installed)
Interior
- S14 front seats
- Greddy white faced oil pressure gauge
- Greddy white faced boost gauge
- Greddy white faced water temp gauge
- White faced gauges for stock console
- Apexi S-AFC II
- JDM style two deck radio
Exterior
- Silvia conversion
- GTR grill
- Santeca HID kit (not installed)
- Rear 5 lug conversion
- Kosei K1 16x8.5 rear rims w/245 tires
- Buddy Club P1 16x7.5front rims w/225 tires
http://project240.com/pictures/240/cardone.jpg
http://project240.com/pictures/240/cardone2.jpg
http://project240.com/pictures/240/cardone3.jpg
http://project240.com/pictures/240/cardone4.jpg
http://project240.com/pictures/240/cardone7.jpg
Drop me a e-mail ([email protected]) or PM if you are interested. If you pay with a casiers check you will have to wait for it to clear before you can have the car.....
Alan