xxnak219xx
05-11-2016, 08:27 PM
Looking to sell my 92 240 Hatch RB25 swap
Bought it as a project car, dropped over $6k in parts, only to get halfway through, now after years of sitting in the garage I'm hoping somebody can take it and make it their own.
Asking $4800 OBO
Keep in mind car must be trailer-ed since it is not running.
Car was stripped down, all engine bay rust points were cut out and patched, interior and engine bay painted black.
What's included:
Stock seats
Uncracked front dash
R33 Cluster
S1 RB25DET stock internals w/ S2 coils and wiring
Brand new oil pan
Stock RB 5speed Trans
Wiring stripped to essentials (needs completion)
Stock turbo and ex mani
SS Turbo Lines
New still in the box Greddy Timing Belt
New still in the box Nismo Water Pump
Mounted on R33 Xmember with Syko Mounts
Q45 TB
MAF - have a variety of MAFs depending on how you plan to have it wired and tuned.
HKS SSQV BOV (BOV flange needs to be mounted)
Real Greddy Intake Mani
Full 3" Exhaust Turbo Back
Old School Apexi AVCR w/ brand new solenoid and pressure sensor
Walbro 255 HP
Nismo Adj FPR
Brand New Koyo Radiator
2x SPAL 12" HP Pusher Fans
Nismo Thermostat
RB-Performance FMIC
Greddy Oil Cooler Adaptor
B&M Oil Cooler w/ SS lines
Aluminum Driveshaft
Nismo SS Clutch Line
Autometer Ultra-Lite 2 1/16
Water temp, Oil temp, and Oil press gauges (New unmounted)
Also have some rear S14 5 lug hubs to throw in.
There is still plenty of work left to do for you to make it your own.
Needs a new windshield and passenger door has dent.
Hatch needs patching where stock spoiler was removed. Planned to replace all with CF just never got around to it.
Some Pics:
http://i.imgur.com/WMMVK5e.jpg
http://imgur.com/4jwpADm
(http://i.imgur.com/4jwpADm.jpg)
[IMG]http://imgur.com/uRuyoi6
(http://i.imgur.com/uRuyoi6.jpg)
[IMG]http://imgur.com/e01nYoQ
(http://i.imgur.com/e01nYoQ.jpg)
[IMG]http://imgur.com/AyjBnEB
[Imgur](http://i.imgur.com/AyjBnEB.jpg)
Anyone looking to do an RB25 swap... you will not amass these parts for less than $5k. The motor set, mounts, Greddy Intake mani, and Aluminum Driveshaft alone are $3700.
Feel free to PM offers but I'd prefer emails as I can respond quicker.
Send Emails to [email protected]
Please put either Zilvia or RB25 240 in the subject so I don't accidentally delete it.
Thanks,
Kevin
Bought it as a project car, dropped over $6k in parts, only to get halfway through, now after years of sitting in the garage I'm hoping somebody can take it and make it their own.
Asking $4800 OBO
Keep in mind car must be trailer-ed since it is not running.
Car was stripped down, all engine bay rust points were cut out and patched, interior and engine bay painted black.
What's included:
Stock seats
Uncracked front dash
R33 Cluster
S1 RB25DET stock internals w/ S2 coils and wiring
Brand new oil pan
Stock RB 5speed Trans
Wiring stripped to essentials (needs completion)
Stock turbo and ex mani
SS Turbo Lines
New still in the box Greddy Timing Belt
New still in the box Nismo Water Pump
Mounted on R33 Xmember with Syko Mounts
Q45 TB
MAF - have a variety of MAFs depending on how you plan to have it wired and tuned.
HKS SSQV BOV (BOV flange needs to be mounted)
Real Greddy Intake Mani
Full 3" Exhaust Turbo Back
Old School Apexi AVCR w/ brand new solenoid and pressure sensor
Walbro 255 HP
Nismo Adj FPR
Brand New Koyo Radiator
2x SPAL 12" HP Pusher Fans
Nismo Thermostat
RB-Performance FMIC
Greddy Oil Cooler Adaptor
B&M Oil Cooler w/ SS lines
Aluminum Driveshaft
Nismo SS Clutch Line
Autometer Ultra-Lite 2 1/16
Water temp, Oil temp, and Oil press gauges (New unmounted)
Also have some rear S14 5 lug hubs to throw in.
There is still plenty of work left to do for you to make it your own.
Needs a new windshield and passenger door has dent.
Hatch needs patching where stock spoiler was removed. Planned to replace all with CF just never got around to it.
Some Pics:
http://i.imgur.com/WMMVK5e.jpg
http://imgur.com/4jwpADm
(http://i.imgur.com/4jwpADm.jpg)
[IMG]http://imgur.com/uRuyoi6
(http://i.imgur.com/uRuyoi6.jpg)
[IMG]http://imgur.com/e01nYoQ
(http://i.imgur.com/e01nYoQ.jpg)
[IMG]http://imgur.com/AyjBnEB
[Imgur](http://i.imgur.com/AyjBnEB.jpg)
Anyone looking to do an RB25 swap... you will not amass these parts for less than $5k. The motor set, mounts, Greddy Intake mani, and Aluminum Driveshaft alone are $3700.
Feel free to PM offers but I'd prefer emails as I can respond quicker.
Send Emails to [email protected]
Please put either Zilvia or RB25 240 in the subject so I don't accidentally delete it.
Thanks,
Kevin