kleenS14
10-25-2015, 08:35 AM
All parts are located in Wv 25403, but I work daily in northern va so I can bring things down there if its closer. Only accept paypal, fees and shipping not included in prices, unless your a local pickup then of course cash is fine. Prices are obo, but don't give me some ridiculous number. All parts are in good condition, Im just going to the dark side so dumping all my sr stuff to put money into the ls. paypal address is [email protected]
550$Nismo Super Copper Mix Single Plate clutch kit for s15 6 speed. Clutch kit is in great condition. Low miles, less than 5k. Disc has plenty of life on it (orange is just minor surface rust from sitting, not an issue at all) and I had the flywheel resurfaced so its ready to go. Comes with all hardware needed. Great clutch.
http://oi63.tinypic.com/jp7qqs.jpg
http://oi68.tinypic.com/2r4k0wk.jpg
http://oi66.tinypic.com/fy074h.jpg
350$Nismo Super Copper Mix Single Plate clutch kit for 5 speed sr trans. Disc is well used and doesnt have much life left on it. I used a Spec 6 puck instead of the Nismo replacement. Any disc for an SR will work as long as its stock diameter. Would recommend replacing. Also had flywheel resurfaced and comes with all hardware.
http://oi63.tinypic.com/3005wmc.jpg
http://oi68.tinypic.com/1h4hhe.jpg
150$Genuine Greddy SR oil pan. The real deal, not a knock off. Minor scoring on outside of sealing flange from removing multiple times. Pretty self explanatory beyond that though. Put through the parts washer to clean it up, and rtv has been removed.
http://oi66.tinypic.com/msycn7.jpg
http://oi65.tinypic.com/2itiidc.jpg
350$Tomei sr head studs complete. Torqued 2-3x. Arguably the best set you can get. Has the tapered bottoms for more accurate spread of torque.
http://oi65.tinypic.com/1hrmo4.jpg
175$ Tomei Type A Valve spring set. Light use. Required for 12.5mm lift and or procams. Good set of springs.
http://oi61.tinypic.com/120t8k3.jpg
280$ Tial 44mm MV-R in Black. Not sure what spring is in it but can check if its really needed. Worked properly when removed. Comes with fire ring, fittings and both clamps.
http://oi59.tinypic.com/2rnj61e.jpg
http://oi61.tinypic.com/o0zec4.jpg
120$ S14 front timing cover/oil pump. Basically brand new, used for about 50 miles.
http://oi61.tinypic.com/5w4zq.jpg
http://oi60.tinypic.com/29572ph.jpg
500$ Tomei 740cc Injectors. Will come with fuel rail, seeing as I don't care to remove them. Can come with lower intake runners if you want.
http://oi58.tinypic.com/52gv40.jpg
140$ S14 Valve Cover. Good condition, painted tomei style blue with decal. Front breather port is threaded with -10an fitting installed.
http://oi64.tinypic.com/xlgti0.jpg
70$ S14 Drop in Wahlbro 255 fuel pump. Comes with everything pictured for simple install. Would put a filter sock on it, other than that good to go.
http://oi65.tinypic.com/1rf4w2.jpg
75$ t25 style wastegate actuator. Opens at 12psi, good upgrade for stock turbos. Came off my ARMS kit.
http://oi64.tinypic.com/23ux5z6.jpg
Much more coming but we'll do this to start....Holla!
550$Nismo Super Copper Mix Single Plate clutch kit for s15 6 speed. Clutch kit is in great condition. Low miles, less than 5k. Disc has plenty of life on it (orange is just minor surface rust from sitting, not an issue at all) and I had the flywheel resurfaced so its ready to go. Comes with all hardware needed. Great clutch.
http://oi63.tinypic.com/jp7qqs.jpg
http://oi68.tinypic.com/2r4k0wk.jpg
http://oi66.tinypic.com/fy074h.jpg
350$Nismo Super Copper Mix Single Plate clutch kit for 5 speed sr trans. Disc is well used and doesnt have much life left on it. I used a Spec 6 puck instead of the Nismo replacement. Any disc for an SR will work as long as its stock diameter. Would recommend replacing. Also had flywheel resurfaced and comes with all hardware.
http://oi63.tinypic.com/3005wmc.jpg
http://oi68.tinypic.com/1h4hhe.jpg
150$Genuine Greddy SR oil pan. The real deal, not a knock off. Minor scoring on outside of sealing flange from removing multiple times. Pretty self explanatory beyond that though. Put through the parts washer to clean it up, and rtv has been removed.
http://oi66.tinypic.com/msycn7.jpg
http://oi65.tinypic.com/2itiidc.jpg
350$Tomei sr head studs complete. Torqued 2-3x. Arguably the best set you can get. Has the tapered bottoms for more accurate spread of torque.
http://oi65.tinypic.com/1hrmo4.jpg
175$ Tomei Type A Valve spring set. Light use. Required for 12.5mm lift and or procams. Good set of springs.
http://oi61.tinypic.com/120t8k3.jpg
280$ Tial 44mm MV-R in Black. Not sure what spring is in it but can check if its really needed. Worked properly when removed. Comes with fire ring, fittings and both clamps.
http://oi59.tinypic.com/2rnj61e.jpg
http://oi61.tinypic.com/o0zec4.jpg
120$ S14 front timing cover/oil pump. Basically brand new, used for about 50 miles.
http://oi61.tinypic.com/5w4zq.jpg
http://oi60.tinypic.com/29572ph.jpg
500$ Tomei 740cc Injectors. Will come with fuel rail, seeing as I don't care to remove them. Can come with lower intake runners if you want.
http://oi58.tinypic.com/52gv40.jpg
140$ S14 Valve Cover. Good condition, painted tomei style blue with decal. Front breather port is threaded with -10an fitting installed.
http://oi64.tinypic.com/xlgti0.jpg
70$ S14 Drop in Wahlbro 255 fuel pump. Comes with everything pictured for simple install. Would put a filter sock on it, other than that good to go.
http://oi65.tinypic.com/1rf4w2.jpg
75$ t25 style wastegate actuator. Opens at 12psi, good upgrade for stock turbos. Came off my ARMS kit.
http://oi64.tinypic.com/23ux5z6.jpg
Much more coming but we'll do this to start....Holla!