JrDarknes
10-07-2015, 05:52 PM
Ok, I'm really hoping you guys can help me. I really want to start this car already.
[Spark Issue]
I just swapped in an RB20DET. I bought a wiring specialties harness for it. For some reason though, four of the plugs would not fit. My CAS Plug, Igniter Plug, Coolant Temp Plug and ECCS Plug. I contacted them and they said its because my RB20 is a redtop?? I told them there no way, this is a r32 silvertop rb20.
https://farm6.staticflickr.com/5793/21404578894_00d3b2ce8b.jpg (https://flic.kr/p/yBs4zG)[/url] [url=https://www.flickr.com/photos/[email protected]/] (https://flic.kr/p/yBs4zG)
They responded well the connectors seem to be from a rb20 redtop from their experience. I just say fuck it, can I wire the new harness to my old connectors and they said it should be fine.
My question is, Did I wire it correctly, because currently I am getting no spark.
Igniter
The New plug( Wiring Specialties)----------------Old Plug (Original)
1 Blue/Green---------------------------------------1 Blue/Orange
2 Blue/Black--------------------------------------- 2 Blue/Black
3 Blue/Red------------------------------------------3 Blue/Red
4 Blue/Yellow-------------------------------------- 4 Blue/Yellow
5 Blue------------------------------------------------5 Blue
6 Blue/White-----------------------------------------6 Blue/White
Assuming to wire it, you just connect number 1 to 1, 2 to 2 and etc right? If so I did that and I'm still getting no spark?
[Fried Ecu Issue]
Now this had pisssed me off. Idk what could of had caused it. Every time I would start it, I had no problem with the ecu, but when I had disconnected the fuel pump plug ( the blue connector in the trunk to the fuel pump assembly) I forgot to plug it back in. I put the car in the ON position and I hear a bussing then suddenly smoke. Fried my ecu. Could this had been because I forgot to plug it back in or could this be a wiring problem. Because like I just mentioned it wouldnt buss at all everytime I switched it to on, but the time I tried it with that fuel pump plug not plugged in it buzzed and fried.
[Spark Issue]
I just swapped in an RB20DET. I bought a wiring specialties harness for it. For some reason though, four of the plugs would not fit. My CAS Plug, Igniter Plug, Coolant Temp Plug and ECCS Plug. I contacted them and they said its because my RB20 is a redtop?? I told them there no way, this is a r32 silvertop rb20.
https://farm6.staticflickr.com/5793/21404578894_00d3b2ce8b.jpg (https://flic.kr/p/yBs4zG)[/url] [url=https://www.flickr.com/photos/[email protected]/] (https://flic.kr/p/yBs4zG)
They responded well the connectors seem to be from a rb20 redtop from their experience. I just say fuck it, can I wire the new harness to my old connectors and they said it should be fine.
My question is, Did I wire it correctly, because currently I am getting no spark.
Igniter
The New plug( Wiring Specialties)----------------Old Plug (Original)
1 Blue/Green---------------------------------------1 Blue/Orange
2 Blue/Black--------------------------------------- 2 Blue/Black
3 Blue/Red------------------------------------------3 Blue/Red
4 Blue/Yellow-------------------------------------- 4 Blue/Yellow
5 Blue------------------------------------------------5 Blue
6 Blue/White-----------------------------------------6 Blue/White
Assuming to wire it, you just connect number 1 to 1, 2 to 2 and etc right? If so I did that and I'm still getting no spark?
[Fried Ecu Issue]
Now this had pisssed me off. Idk what could of had caused it. Every time I would start it, I had no problem with the ecu, but when I had disconnected the fuel pump plug ( the blue connector in the trunk to the fuel pump assembly) I forgot to plug it back in. I put the car in the ON position and I hear a bussing then suddenly smoke. Fried my ecu. Could this had been because I forgot to plug it back in or could this be a wiring problem. Because like I just mentioned it wouldnt buss at all everytime I switched it to on, but the time I tried it with that fuel pump plug not plugged in it buzzed and fried.