cheapest widest properely offsetted 4x114.3 wheels, what are they?

[NotDave]

im curious to see any

15x7+
16x8+
17x9+

wheels in 4x114.3 bolt pattern that would fit a 240sx nicely. pics? :x:

seems like fn01r-c and dt-0r5 are the only ones that dont cost $500 per wheel :bite:

[Var]

if you are buying rims you are getting ripped off. i suggest you go 5-lug so you ca buy some reasonably priced american made rims.

[NotDave]

not everybody wants or has the moola to go 5 lug. i was just curious to see if there were any options for us people who are stuck with 4 lugs and want decent rims.

[TheTimanator]

Custom drilled Kosei K-1's
at least for 15-16"


15X7 BLANKS ET17 SIL K1 RACING * $179.00
15X7 BLANKS ET27 SIL K1 RACING * $179.00
15X7 BLANKS ET38 SIL K1 RACING * $179.00
15X7 BLANKS ET45 SIL K1 RACING * $179.00
15X8 BLANKS ET12 SIL K1 RACING * $199.00
15X8 BLANKS ET22 SIL K1 RACING * $199.00
15X8 BLANKS ET32 SIL K1 RACING * $199.00
16X7.5 BLANK ET12 K1 RACING * $199.00
16X7.5 BLANK ET22 K1 RACING * $199.00
16X7.5 BLANK ET32 K1 RACING * $199.00
16X7.5 BLANK ET43 K1 RACING * $199.00
16X8.5 BLANK ET17 K1 RACING * $209.00
16X8.5 BLANK ET27 K1 RACING * $209.00
16X8.5 BLANK ET37 K1 RACING * $209.00
17X7.5 BLANK ET35 K1 RACING * $239.00

http://forums.freshalloy.com/ubbthreads/showflat.php?Cat=&Board=UBB20&Number=67699987&page=0&view=collapsed&sb=5&o=&fpart=1

[NotDave]

these aint bad

16X8.5 BLANK ET27 K1 RACING * $209.00

its just the color :goyou:

[ThatGuy]

2 cans of spray-paint and they can be any color you want.

[HaLo]

forget about color!!! those are great track wheels! :D

[KwKouki]

I found a set of longchamps 15x7.5 +5 for 920 shipped. They are out there, you just have to look

[Salty_X]

these aint bad

16X8.5 BLANK ET27 K1 RACING * $209.00

its just the color :goyou:
Am I missing something? What's wrong with silver? :confused:

Oh yeah, 8.5 +17 man, +17... word up. :coold:


Oh yeah pt. 2, SSR Mesh can be found for pretty cheap in 4-lug, you just have to give up ever having Z brakes.

[pruto]

american racing AR767 steelies :)

[TheTimanator]

Am I missing something? What's wrong with silver? :confused:
Oh yeah, 8.5 +17 man, +17... word up. :coold:

Yeah whats wrong with silver?!?! :rawk:

8.5 +17 if you want to strech your tires. I think I'd prolly go with the 16x8.5 +27 all round for an easier fit. That way I wouldn't have to run more than a couple degrees of negative camber. with 225's-245's maybe

8.5 +17 with 215's and about 2-3 degrees of negative camber maybe? maybe 225's? I too tired

Also, SSR comp. If I had the money :drool: (I'm pretty sure there considerably more) cept there's a billion knock-offs of those

And pruto...those wheels are heavy! haha. My freind bought them for his jeep (or at least some VERY similar) for $41 a wheel :faint:

[NotDave]

american racing AR767 steelies :)
http://imagescommerce.bcentral.com/merchantfiles/5029204/AR767.jpg
they dont look too bad actually. i wonder what the offset is? no 4 bolt pattern :squint:

and what size...i only know metric :Ownedd:

http://www.reaction-image.net/albums/album93/sizes.jpg

[pruto]

i have 15x7+0, i also see 15x8 +6 and 15x8 -12

too bad on the no 4 lugs. they are also heavy, being steelies, but at 50 bucks a piece, its cheap =P

[Salty_X]

and what size...i only know metric :Ownedd:

http://www.reaction-image.net/albums/album93/sizes.jpg
25.4mm = 1 inch.
4.5 x 25.4 = 114.3

[rsdeo]

These should fit your order.

http://www.zilvia.net/f/showthread.php?t=100552

[yudalicious]

i don't think they make those kosie K1s anymore... I could be mistaken...
www.autornd.com has the rotas 16x8 +20, 16x8 +10 I think.

[Alexe]

i don't think they make those kosie K1s anymore... I could be mistaken...
www.autornd.com has the rotas 16x8 +20, 16x8 +10 I think.

says they wont clear z32 brakes. you think if you got the +20's and used a 10mm spacer it would clear z brakes?

[Johny5]

hey guys, don't bother posting in this thing anymore. dumbass rsdeo brought it up from 2 years ago to post his pathetic and ugly 19" wheels. i hope that you actually take longer to sell them now.

canada fail sir, canada fail.

[TheTimanator]

i don't think they make those kosie K1s anymore... I could be mistaken...
www.autornd.com has the rotas 16x8 +20, 16x8 +10 I think.
You are correct, but back when I made that post they were! This thread is really old and bumped by somone trying to sell stuff. :squint:

[FaLKoN240]

Gg Old Ass Thread Newb.

[Alexe]

you guys mind answering my question though? please and thanyou

[rsdeo]

hey guys, don't bother posting in this thing anymore. dumbass rsdeo brought it up from 2 years ago to post his pathetic and ugly 19" wheels. i hope that you actually take longer to sell them now.

canada fail sir, canada fail.

Poor baby, it's sucks like you that give the rest of the world a bad perception on the US.

[TheTimanator]

you guys mind answering my question though? please and thanyou
ways to get an answer to your question:
1.) search the forums (i searched a little and didn't find anything)
2.) contact auto rnd and see if they know.

good luck

[Alexe]

ways to get an answer to your question:
1.) search the forums (i searched a little and didn't find anything)
2.) contact auto rnd and see if they know.

good luck

thankyou sir. i already sent an email but i was hoping to get a quick answer.

[rsdeo]

thankyou sir. i already sent an email but i was hoping to get a quick answer.


Okay do the following.

Take a long level. While the car is sitting normaly on a flat surface such as your garage sit the level on the ground verticaly while the side sits on the fender lip. The level should be sitting straight up, make sure the bubble is between the markers. Now measure the distance from the level to the wheel lip. You now will know the distance from the fender lip to the rim. Now remove the rim and measure the front spacing. Then add the value measured above to this measurement. You now have maximum front spacing.

We know that generally maximum backspacing is 6", so add the maximum frontspacing to the maximum frontspacing. You now have a total measured maximum rim width.

To get the maximum rim width as speced by the wheel manufacturers subtract 1" from the total measured maximum rim width.

Repeat for the other end of the car.

[TheTimanator]

^^^ huh? he's trying to find out if the Rota Grids will clear z-brakes and unless he already has the wheels how is he suspose to figure that out?

[Alexe]

cocain is a helluva drug

[yudalicious]

says they wont clear z32 brakes. you think if you got the +20's and used a 10mm spacer it would clear z brakes?
16x8 +20 w/ 10mm spacers would make it 16x8 +10, which autornd offers... and no, those wheels in 16x8 +10 won't clear Z brakes...

[rsdeo]

^^^ huh? he's trying to find out if the Rota Grids will clear z-brakes and unless he already has the wheels how is he suspose to figure that out?

First post said nothing about clearing brakes.

im curious to see any

15x7+
16x8+
17x9+

wheels in 4x114.3 bolt pattern that would fit a 240sx nicely. pics? :x:

seems like fn01r-c and dt-0r5 are the only ones that dont cost $500 per wheel :bite:

Which calipers, 26mm or 30mm?

Maybe the following will help.

http://www.materials.unsw.edu.au/~sford/Z32-1.jpg

http://www.materials.unsw.edu.au/~sford/Z32-2.jpg

Lets start off by using the right information to give to the wheel manufacturers.

[rsdeo]

How about these Skyline R33 GTR Brembos?

http://img66.imageshack.us/img66/8083/brembo3ws.jpg

Now we are talking calipers.

[rsdeo]

How about these Skyline R33 GTR Brembos?

http://img66.imageshack.us/img66/8083/brembo3ws.jpg

Now we are talking calipers.

[TheTimanator]

First post said nothing about clearing brakes.
true, but the first post was posted last year.

What we need to figure out is how much room is between the rotor hat (wheel mounting point) and the outer edge of the caliper. That way anybody who i selling there wheels or wondering if there current rims will clear if they upgrade can just measure from the mounting pad to the spokes. I'll bet this has already been figured out somewhere on these boards or freshalloy or something.

^^^correct me if I wrong

[rsdeo]

true, but the first post was posted last year.

What we need to figure out is how much room is between the rotor hat (wheel mounting point) and the outer edge of the caliper. That way anybody who i selling there wheels or wondering if there current rims will clear if they upgrade can just measure from the mounting pad to the spokes. I'll bet this has already been figured out somewhere on these boards or freshalloy or something.

^^^correct me if I wrong

~40mm with the 30mm caliper/disc setup is the rubbing point. 45mm to be safe at a radius of around 110mm from the center of the hub or wheel..

Johny5, funny it takes a Canadian to figure it out and actually post information that others can use.

[RB26Sileighty]

max sport
18x8.5
18x9.5 4x114

[SoSideways]

The Gram Light 57pro in 18" diameter can be made in custom lug pattern (to 4x114.3) and I think up to 11" wide, if not wider.

I don't remember by I think some Work wheels are also custom lug patterned and gets pretty wide.

[A Spec Products]

The Gram Light 57pro in 18" diameter can be made in custom lug pattern (to 4x114.3) and I think up to 11" wide, if not wider.

I don't remember by I think some Work wheels are also custom lug patterned and gets pretty wide.

57 pro goes up to 18x10 in 4 lug (free offsets)

Work has a lot of 4 lug options, yes, cause its custom (shameless plug 15x9+0 Equip 03's gold in stock, pair only tho)

And lets not forget Grenade GX01s, 17x9+15, 20 / 18x9+20 all 4 lug

[midnite_180]

Ar centerlines relly big offset and can find them in 14, 15, 16 inch with lots of different offsets and most of the time for less than $700 for a full set.

[ESone3]

http://www.zilvia.net/f/showthread.php?t=96018

special group buy on these! Only custom order!

[Alexe]

16x8 +20 w/ 10mm spacers would make it 16x8 +10, which autornd offers... and no, those wheels in 16x8 +10 won't clear Z brakes...

yes +20 with a 10mil spacer will be +10, but the wheel will still be 10 mil further from the caliper