anthonyduane94
07-25-2015, 10:46 AM
1977 Datsun 280z For Sale/ Trade
This is a project that is currently in process. I bought the car with intentions on driving it to California. I'm moving and might not have the complete means and money for finishing the car. Unfortunately things never go as planned and need to move on so the car will stay here while I go to Cali. The engine was a full drop out from a 99 TransAm LS1/T56 car. Only 90,xxx miles on the original car. Everything for the swap was bought brand new excluding the alternator.
Zero Rust! Low mileage chassis registered as Swapped car
Fresh 241 Stock Heads
New water pump
New Oil Pan
New Corvette MAF
New Oil/Coolent senders
New Pullys & Belts
Walbro 255
Corvette Filter / Regulator
Russel Pushloc Fuel Lines(Alcohol Safe)
Jegs PushLoc Hose ends
Factory Harness
PSI Tuned ECM
Current Performance LS Harness Wiring
AEM WideBand
Oil Press/Coolent Temp Gauges Work
JCI Engine & Trans Mounts LS1
JCI Driveshaft
JCI Headers LSZ swap headers
Magnaflow Muffler Dual 2.5in/out
JCI Coolant Hoses
JTR Intake Kit
3in Filter K&N
Tilton Clutch Master 7/8
TickMaster Clutch kit w/ speed bleeder (fresh) 1000mi on clutch
Poly Bushings All Around
15" Aero Wheels
Unfortunately with my luck I was sold a trans that was on its last leg. After test driving the car a few times I did one good pull in 3rd and by the end of it the car was stuck in 3rd. Trans will need rebuilt. Most likely the 3-4 synchro finally took a crap during the high RPM pull. Full rebuilt kit for tans is only $325
Car also comes with a set of Sparco seats for right price.
I'm sure I'm missing plenty of parts, but car currently runs and drives in 3rd. Lol could even drive onto a trailer. Starts up with no hesitation, but could use a tune I'm sure once exhaust is put on. Drove the car with no issues until trans prob. Once fixed
Car is a perfect start. Only needs gauges, brakes, and accessories and appearance items to make perfectly road ready.
I am interested in trades for something that won't need much work at all or no work at all. Must be MANUAL, would prefer something quick, fast, or reliable.
Can price is $8700 obo
This is a project that is currently in process. I bought the car with intentions on driving it to California. I'm moving and might not have the complete means and money for finishing the car. Unfortunately things never go as planned and need to move on so the car will stay here while I go to Cali. The engine was a full drop out from a 99 TransAm LS1/T56 car. Only 90,xxx miles on the original car. Everything for the swap was bought brand new excluding the alternator.
Zero Rust! Low mileage chassis registered as Swapped car
Fresh 241 Stock Heads
New water pump
New Oil Pan
New Corvette MAF
New Oil/Coolent senders
New Pullys & Belts
Walbro 255
Corvette Filter / Regulator
Russel Pushloc Fuel Lines(Alcohol Safe)
Jegs PushLoc Hose ends
Factory Harness
PSI Tuned ECM
Current Performance LS Harness Wiring
AEM WideBand
Oil Press/Coolent Temp Gauges Work
JCI Engine & Trans Mounts LS1
JCI Driveshaft
JCI Headers LSZ swap headers
Magnaflow Muffler Dual 2.5in/out
JCI Coolant Hoses
JTR Intake Kit
3in Filter K&N
Tilton Clutch Master 7/8
TickMaster Clutch kit w/ speed bleeder (fresh) 1000mi on clutch
Poly Bushings All Around
15" Aero Wheels
Unfortunately with my luck I was sold a trans that was on its last leg. After test driving the car a few times I did one good pull in 3rd and by the end of it the car was stuck in 3rd. Trans will need rebuilt. Most likely the 3-4 synchro finally took a crap during the high RPM pull. Full rebuilt kit for tans is only $325
Car also comes with a set of Sparco seats for right price.
I'm sure I'm missing plenty of parts, but car currently runs and drives in 3rd. Lol could even drive onto a trailer. Starts up with no hesitation, but could use a tune I'm sure once exhaust is put on. Drove the car with no issues until trans prob. Once fixed
Car is a perfect start. Only needs gauges, brakes, and accessories and appearance items to make perfectly road ready.
I am interested in trades for something that won't need much work at all or no work at all. Must be MANUAL, would prefer something quick, fast, or reliable.
Can price is $8700 obo