memphiss13
08-02-2004, 05:27 PM
i found this somewhere and i can't remember where. i just want to make sure it is accurate. this seems to be something you never really read much about. and also if anybody knows where i can find wiring instructions for s13 SR into S14 that would be great. thanks in advance
this is what i found:
Move # 1(purple) to # 7(Empty). Move # 2 (Blue with yellow tracer) to # 14.
# 14 should be for ABS - It doesn’t need to be used again- # 14 should be Blue with Red tracer.
Move # 3(Blue with Black tracer) to # 15. Put wire from # 15(Green with white tracer) to #26. # 26 should be empty but it may have a blue and green wire in it. If this is so just take it out for now.
Remove wire from # 13 - It will either be Gray or Greenand Yellow - This wire is for ABS and can be discarded. Now move Yellow wire from # 4 to port # 13. Next move wire from # 5 to # 25.
Next, put the Green and Black wire from # 8 into the port # 19 - Move the wire from # 19 (Green and Redstripe) into port # 29. The brown wire from # 29 is for the heated O2 sensor on the JDM car. USDM does not have wires to supply and power to heated O2 sensor until OBD2.
The wire from # 28(Orange) to # 11 - # 11 may have a Black wire with White tracer. If this is so then it needs to be adapted to fit in port # 34. These are the bigger ports and you have to rape a pin and a section of wire from the old wiring harness.
Next move wire from # 12 (Green and Orange) to # 17-Move # 17 (Green and Yellow) to port # 6. # 6 should be empty (unless car is auto).
Next put Green Wire from # 18 into port # 27 - Put the wire from port # 27 (Orange and Black) into # 4. You should have already removed this wire from # 4 earlier in this installation.
Move wire from # 25 (either Red or Green) to # 3.
There is a Purple wire with a white tracer in port # 54 on the ECU. Cut this wire with enough length to run it to the main harness connector. Rape a pin and section of wire from the old body connector and connect the Purple and White wire to port # 34.
this is what i found:
Move # 1(purple) to # 7(Empty). Move # 2 (Blue with yellow tracer) to # 14.
# 14 should be for ABS - It doesn’t need to be used again- # 14 should be Blue with Red tracer.
Move # 3(Blue with Black tracer) to # 15. Put wire from # 15(Green with white tracer) to #26. # 26 should be empty but it may have a blue and green wire in it. If this is so just take it out for now.
Remove wire from # 13 - It will either be Gray or Greenand Yellow - This wire is for ABS and can be discarded. Now move Yellow wire from # 4 to port # 13. Next move wire from # 5 to # 25.
Next, put the Green and Black wire from # 8 into the port # 19 - Move the wire from # 19 (Green and Redstripe) into port # 29. The brown wire from # 29 is for the heated O2 sensor on the JDM car. USDM does not have wires to supply and power to heated O2 sensor until OBD2.
The wire from # 28(Orange) to # 11 - # 11 may have a Black wire with White tracer. If this is so then it needs to be adapted to fit in port # 34. These are the bigger ports and you have to rape a pin and a section of wire from the old wiring harness.
Next move wire from # 12 (Green and Orange) to # 17-Move # 17 (Green and Yellow) to port # 6. # 6 should be empty (unless car is auto).
Next put Green Wire from # 18 into port # 27 - Put the wire from port # 27 (Orange and Black) into # 4. You should have already removed this wire from # 4 earlier in this installation.
Move wire from # 25 (either Red or Green) to # 3.
There is a Purple wire with a white tracer in port # 54 on the ECU. Cut this wire with enough length to run it to the main harness connector. Rape a pin and section of wire from the old body connector and connect the Purple and White wire to port # 34.