FS: Z32 loaded aluminum calipers with PBM 350z track rotors

[brn2slid]

these have been sold

[RalliartRsX]

How much for just the rotors and what is the thickness on them??

[Johnny Coquí]

Bump, what's the pricing on lines, brackets and rotors?

[kilamax03]

pmed........

[brn2slid]

Just trying to sell it all together guys. Hell of a setup here and well worth the money if you do your research. 550 shipped within the states. HI and AK excluded on this.

[RalliartRsX]

Can you answer my question in regards to rotor thickness then??

[supersayianjim]

and you need to state that these will only work with 17" wheels!!

[RalliartRsX]

and you need to state that these will only work with 17" wheels!!

That is a blanket statement and probably does not apply to all wheels (fitment is dependent on offset, inner barrell clearance and width).

[cespana]

How much just for the rotors and brackets?

Is there any chance to part out just that?

Enviado desde mi U9200 usando Tapatalk 2

[brn2slid]

Can you answer my question in regards to rotor thickness then??

When I get a chance to measure I will let you know, in the meantime, there is google, you can search the new spec and be ready to know how much life is left.

and you need to state that these will only work with 17" wheels!!

The ignorance of this response has me baffled.

That is a blanket statement and probably does not apply to all wheels (fitment is dependent on offset, inner barrell clearance and width).

This is true however there is no need for me to state what wheels these will work with, it is quite obvious you can't fit small wheels with oversized rotors. Still baffled that he even posted that.

How much just for the rotors and brackets?


Is there any chance to part out just that?

Enviado desde mi U9200 usando Tapatalk 2

As mentioned above, sold all together. There are about 5 people in line before you if I do end up separating.

[RalliartRsX]

The numbers are below for the rotor thickness per FSM for recommended minimum thickness

Standard thickness for the 350Z Brembos : 30mm
Min wear thickness for the 350Z Brembos : 28.4mm
If the rotors are within reason, I am interested in the kit.

Thanks!

[brn2slid]

The numbers are below for the rotor thickness per FSM for recommended minimum thickness

Standard thickness for the 350Z Brembos : 30mm
Min wear thickness for the 350Z Brembos : 28.4mm
If the rotors are within reason, I am interested in the kit.

Thanks!

I just have to source a gauge and snap some pictures for you

[brn2slid]

Still sitting on this great pair of front brakes.

I couldn't find my caliper so I had to use a tape measure, the rotors are at 1-1/8, which equates roughly to 31mm

[brn2slid]

A lot of flakes, someone pick these up!

[kilamax03]

Went part out

[FaLKoN240]

You can ship each rotor in a flat rate box with each bracket :)

[brn2slid]

Went part out

No I won't, I have had too many offers on the rotors/brackets and no interest in the calipers. Why would I part out? just to sit on the calipers

You can ship each rotor in a flat rate box with each bracket :)
Yes I could, along with both calipers.

I don't see why you guys can't just buy it all together and sell your calipers if you want it so bad.

If you guys want the rotors/brackets I better start getting higher offers for them to justify the loss on the calipers I would take. 550 shipped is a damn good deal for everything here.

[brn2slid]

Possible sale of calipers, all those that were interested in the rotors, contact me again as I deleted your PM's

[brn2slid]

These have been sold.