Fund my smallblock super sale! SR swap inside! Lots of parts! (Sr, s13, z32)

[z'd up]

Tony's "Fund my Smallblock" Sale
Serious offers considered
Sr20det:

-Bare block with pistons(needs one oil squirter $25-30 on eBay and has one bent rod from hydrolock)
-Lower oil pan -- $40
-Upper oil pan -- $50
-Timing chain and guides-- $50
-Crankshaft Girdle --$20
-Lower water neck -- $10
-Stock crank pulley--$20obo
-Oil Pump(needs new front seal)$60

S13
-power mirrors(black)--- $20 a side
-heater controls--- $30obo

Z32
-NA axles--- $40 for both
- 5 lug rear knuckles with parking hardware and cables(missing a few studs, backing plates need love, and one cable is frozen)-- $100obo


SR20DET SWAP
-redtop sr
-t3t4 top mount turbo(50 trim I believe)
-10psi wastegate
-knockoff greddy intake mani
-tomei headgasket
-arp studs
-rocker arm stoppers
-has stock injectors in now. Will come with 550s that need new orings
-FMIC
-KA trans with sr bell housing
-short shifter
-spec clutch
-act pressure plate
-socketed ecu(needs tune bad)
-silicone upper and lower hoses
-vibrant intake tube

Needs- tune and possibly a new MAF. Drove it around some Saturday then went to start it sunday and it wouldn't rev unless I unhooked the MAF. It will idle if anyone is interested in hearing it. I have videos from Saturday of it running and driving and can take ones of how it is now.
$2300 Obo.

SWAP PART OUT PRICING:
Greddy knockoff Intake manifold w/ throttle body and fuel rail and injectors- $250
Top mount t3/t4 turbo, manifold, w/down pipe- $400
FMIC kit(set up for top mount turbo) with greddy knockoff bov(brand new)-$200
Long block with alternator, crank pulley, valve cover, without manifolds, coils, etc.- $1000obo
KA trans w/ SR bellhousing, slave cylinder, act pressure plate, spec full face clutch, short shifter, and flywheel- $550
Socketed 62 ECU- $150




I'll dig around some more. I know for a fact I'm missing stuff. I've got lots and lots of parts. Also have bolts for just about the entire engine if you need any. Looking for SBC parts as trade.
Located in 17527

Text is best 717-six72-440six

[z'd up]

Friday bump...

[wimernw]

sending you a pm

[z'd up]

Added pricing for my swap part out. Don't feel like storing this stuff after it's pulled.

[z'd up]

Bump, will sell the swap without harness and ecu. I may need them. Taking cash offers.

[jbacorn6]

Interested in that FMIC setup. Pics? Brand?

[MrBananaToast]

whats the t3/t4 tubro? and if you part out the swap would the wastegate come with the turbo, manifold and downpipe?

[z'd up]

T3t4 is emusa or eBay as far as I know. Yes the WG will come with the turbo/mani/down pipe. The FMIC is cxracing I think but the piping by the throttle body was cut and changed a little for the top mount intake and the same by the turbo for the top mount.

[z'd up]

Picturessssss

http://i13.photobucket.com/albums/a275/NOSSKYLINE88/1396013271_zps8b9c791b.png (http://s13.photobucket.com/user/NOSSKYLINE88/media/1396013271_zps8b9c791b.png.html)

http://i13.photobucket.com/albums/a275/NOSSKYLINE88/1396740669_zpsc30a5dce.jpg (http://s13.photobucket.com/user/NOSSKYLINE88/media/1396740669_zpsc30a5dce.jpg.html)


Best pic I have of the turbo setup

http://i13.photobucket.com/albums/a275/NOSSKYLINE88/1396740964_zpsf023765b.png (http://s13.photobucket.com/user/NOSSKYLINE88/media/1396740964_zpsf023765b.png.html)

[the head]

Im just interested in the longblock can you ship it?

[z'd up]

The last shipping quote I got on the long block was $307 without crate/pallet cost. Not 100% sure if it would be worth it.