1jz s13 drift car. (pic heavy)

[Javier13]

I just finished swapping a 1jz into my car and man it took me a while haha, ill get into every little detail and hopefully people who do this swap will have a greater knowledge and learned something from me posting all this crap.

(NOTE!!!! IF YOU GUYS ARE DOING A 1JZ SWAP AND NEED A INSIGHT OR HELP WITH SOMETHING PLEASE SEND ME A EMAIL [email protected] AND ILL ANSWER IT AS SOON AS I CAN! ^.^

also if you need any fabrication or knukles hit up my buddy http://odysseypartsshop.bigcartel.com/
All the fabrication work done on this car was done by him and everything is quality work

Set-up: 408hp 386tq
Stock 1jz bottom end and head(from jdm miami)
Ebay t4 manifold welded t3 flange(cheap)
440cc injectors (aristo jdm injectors 2jz)
Circuit Sport FPR a little above 3bar (~45.23psi) ran one on the sr and works amazing
Aem EMS v2 honda box(driftmotion but don't use the jumper harness)
NGK BKR7E gapped 0.024
Tuned by Martin owner of R.S. Enthalpy
Holset He351(5.9L dodge cummins)
tial 44mm 1.3bar spring
tial q bov
Mid mount intercooler(ebay)
R154 extended 3"
one piece driveshaft(local)
sikky sway bar
Wilwood 3/4 clutch master cylinder w/ a adapter
Xcessive motor/trans bracket
Xcessive motor mount and trans mount (I first had circuit sports motor mounts and sat way to fucking low don't use anything else but Xcessove IMO)
Open downpipe (ran out of money to make a full exhaust)
3" intercooler piping
oem flywheel cut
ACT clutch 6puck sprung heavy duty PP
Oil relocation
oil cooler
power steering cooler
Mark Panic milspec wiring harness
custom chassis harness with the bare necessities
AN fittings and lines for everything!!!!!!!!!!!! (erals, russel, and xrp stuff)
circuit sports catch can
isis sr20det radiator
ebay silicone hose chopped up
4" inlet for turbo
HKS mushroom filter
isis radiator for sr20det
stock thermostat
12" x2 electric pull fans (will add 2 more fans on the intercooler to make sure i never over heat)
stock thermostat(going to get another one in the future that opens up cooler, and possibly a swirl pot)

suspension-
front:
Sikky sway bar
hicas steering rack
Odyssey Parts Shop knuckles
25mm extended control arms and boxed
abercombie outer tie rods
tien inner tie rods
fortune auto coilovers 10k
era1 offset rack spacers
energy suspesnion steering rack bushings
Dif steering link solid bushing
spl tension rod
215/40/17 federal evo's... will be going to 235 in the future just that was all i could find at the time

rear:
circuit sports control arms
stock rear LCA
stock sway bar
fortune auto coils 8k
245/40/17 nexen n3000 (these are grippy and last forever )
spl solid subframe bushings


brakes:
all stainless steel lines that i made from earls fittings and lines
z32 front hawk hp + pads
stock rear calipers hawk hp + pads (fucking work awesome when locking up the rear)
S14 brake booster
oem master cylinder

Driveline:
Act clutch
wilwood 3/4 clutch master cylinder
stainless steel 3an clutch line
one piece driveshaft
nismo 2-way
napa reman axles
r154

interior:
custom chassis harness i made(i am in the future going to re-do the harness since its a mess since i was such in a rush to get the car finished so i can focus on school)
stri tachometer, boost gauge
PBM EVDM for oil pressure and water temp
Speed hut fuel level gauge
AEM wideband
sparco sprint 5
RJS cam lock harness
Harness bar
(a bolt in cage will come soon just need more money):)
Era1 shift knob(its too tall I might get something shorter or get their other shift knob)


https://scontent-a-lga.xx.fbcdn.net/hphotos-prn2/t1/p720x720/970124_638052262872852_632413700_n.jpg

http://0-media-cdn.foolz.us/ffuuka/board/a/image/1343/13/1343137252036.jpg

putting back the skid plate before heading to the dyno
https://scontent-b-lga.xx.fbcdn.net/hphotos-prn2/t1/1536423_10203021530408882_547006606_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-ash3/t1/p480x480/995127_639475136063898_67723870_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-frc3/t1/q74/s720x720/998865_639722326039179_2125740404_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-prn1/t1/p180x540/1525531_723685604309517_1605948368_n.jpg

https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-prn2/t1/p180x540/1604807_733827083295369_425117169_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-prn2/t1/1507907_733631323314945_979250661_n.jpg

https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-prn1/t31/p180x540/1599286_738770029468638_395536779_o.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-prn1/t31/893111_738770206135287_2050478480_o.jpg

W61tyt9Lbv0

HIM5dvxNhEQ

sxQMe2PEoCc

facebook link of the response the car has
https://www.facebook.com/photo.php?v=737405309604213&l=1128772417989066220

https://www.facebook.com/photo.php?v=736618686349542&set=vb.100000042524121&type=3&permPage=1
for this video just bare with it till the end and you can see how responsive this 1j is

1st time out in the car @3:15

MVblnjXGdQc

first event in the JZ powerplant
rkuDLJAPWTg

Bank Run:
3_leO68-aBU


I will be positing everything from when i first got the car with a single cam to a dual cam to a sr then to jz. And will get into my backgorund and how i got into drifting and cars. Hope you guys enjoy this build!

[Javier13]

Background info on me and my car. I'm currently a full time student at FAU pursuing Mechanical Engineering and a minor in Mathematics in Boca Raton,FL. I'm originally from Tampa. I love drifting, friends, studying, and keeping to myself a lot lol. I got my 240 when i was 15. I enjoy all music Hardcore, Rap, Metal ect... I'm also a huge video game, anime and manga nerd. I love that shit. I'll list my favorite music, manga, anime, and my dream car list, just so you guys can know who i really am!

Dream Car set-up:
Jzx100-Daily/drift car
newer f350- daily/tow rid
930 RWB Porsche-garage car
r32 4door w/ a 1jz- Competitive drift car

Favorite Bands/Artist:
Issues
The Tempations
Micheal Jackson
Memphis Mayfire
Underoath
Daft Punk
Suicide Silence
Biggy
2-pac
SOD
A7X
TDWP
Blink-182
R, Kelly
Usher
Dream Theater
Green Day
The HAARP Machine
Old Kayne West stuff(his new shit sucks and has no feel to it)
BMTH
Sky Eats Airplanes
Miss May I
Final Fantasy Soundtracks
The Bunny The Bear
Anime OP's and ED's
Outkast
The Drifters
ECT..... i like anything haha except country!

Anime:
Too many to list but just a small list
Kill La Kill
SAO
Gintama
One Piece
really the list is ongoing for fucking ever this includes manga too

Video Games:
All RPG's (Dragon Quest, FF series, Zelda series, Pokemon, Fallout series, KH series, Ni No Kuni, Tales of series, Persona series, Xenosaga series... ect..)
I hate xbox, love sony and i own every sony console except the PS4 because i rather have cool drift car
And select shooter like Titan Fall, Bioshock, and BF games.


I love my family and would do anything for them. And they're are my biggest supporters especially my mom who's an angel who's put up with all my shit almost getting arrested for street sliding, helping me pay for events when I didn't have money. Taking me to school when I broke something on the 240 haha.
My brother who's car really made me want a 240 so much. He was also a big help on helping install all the motors ive gone through, pulling all nighters getting my jz finished up and getting it to the dyno.https://scontent-a.xx.fbcdn.net/hphotos-prn2/t1/166673_492823782778_5916917_n.jpg

There's a shit ton of people that have helped me but you guys would hate me if i continued, but the last kid is seriously my right hand man along with my best friend my little cousin. Now this kid has been with me through hell and back with this build, with hoping onto of curbs (which ill get to further in the story), when i was sliding my car in the rain and we flew into the woods right in-between 2 fucking trees and came out with out a scratch and continued to slide. But we've been through a bunch of shit lol. this dude is rad as fuck is another big supporter of mine.

Now with the build starting all the way back in 2009 when i first bought the 240 it was single cam 5 speed for $700. I Didn't know how to drive stick for shit and thought myself and drove around in a 4x4 single cam 240. I also had no mechanic skill what so fucking ever. https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-ash3/t1/5569_100679743276776_3472377_n.jpg
1st thing i ever did was weld the diff so I can slide in the back of my school which was all dirt. Had a fucking blast in the schools parking lot.

Then i bought my first set of old rusty as fuck stance coilovers, control arms all circuit sports, and 5 lug from Ichiba and a bunch of other suspension goodies to get ready to go drifting. (**Note fuck ichiba and their customer service better off just going with isis or oem shit**). But I became best friends with the dude who was with the dude who sold me the stance coilovers.
https://scontent-a.xx.fbcdn.net/hphotos-prn1/t1/24812_109814309029986_7174447_n.jpg

Sean who was the kid who sold me the coilovers was with who is now my best friend Tyler and the kid that got me into drifting. Here's his old s13 (which you guys can all hate on but we trashed that shit after he hit a gaurd rail a couple times lol) and his 1JZ (which was the main reason i went 1jz) LS400 which we also junked due to money issues with his buisness.

https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/247887_1951667943994_5179944_n.jpg

https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-frc3/t1/s720x720/376928_4053997580921_1309586208_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-prn1/t1/s720x720/12806_4319019046292_1446829534_n.jpg

https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/399248_4501404925825_975251784_n.jpg

https://scontent-a.xx.fbcdn.net/hphotos-ash3/t1/s720x720/734726_4776090072782_1279412207_n.jpg

https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-ash3/t1/q71/s720x720/1003934_10201916077676187_613319785_n.jpg

The ls400 I helped him build was on stance nations facebook, and we junked it and sold everything off of it so he could get more money for his business.

https://scontent-a-lga.xx.fbcdn.net/hphotos-prn2/t1/1375115_697031350308276_1371602801_n.jpg
and there it goes lol!!!

Back to the main story.

A couple weeks after I threw on all the new suspension parts i blew my single cam. Pissed as fuck I had no idea what was going on with the car. It had threw a rod and knocked. This was where I learned how to work with cars and swapped a dual cam into the car. And with the dual cam I did literally everything to swap it in with no knowledge of mechanic.

Then went to my first event at cfrc, I was such a noob and didnt know i needed a helmet and my friend had let me borrow his. And god damn i blew so much dick rode the hell out of the clutch and burnt up the oem clutch disk. Smelled like straight ass hair burning the whole 2 hour drive. My aunt helped me out and bought me a ebay clutch (Which went through so much abuse and never let me down ever!!!!!)

Then I went to my second event full auto at the st. pete times forum. This is where I finally knew what the hell to do. Had a lot of people jump in the car with me and helped me out. I still sucked of course but i was progressing. (I was also straight pipe ka24de which was fucking terrible and obnoxious)
https://scontent-b.xx.fbcdn.net/hphotos-prn1/t1/38379_143183162359767_5887400_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/37333_137108719633878_2356431_n.jpg?lvh=1

https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/37333_136945342983549_6898238_n.jpg?lvh=1

Then i continued going to events and street sliding with my buddy Tyler and kevin for the rest of the year. And started getting good!

https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-ash3/t1/33727_162144390463644_5235633_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-ash3/t1/41049_153627641315319_1674696_n.jpg

https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-prn1/t1/59804_160849683926448_1520084_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-prn1/t1/59698_161588903852526_7097274_n.jpg

Then I fucking shredded through my wiring harness and a bunch of other shit street sliding. The car never ran right ever again. so it was parked for a while and had to get it towed home. (which happened a lot when i went SR20)

https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-ash2/t1/38552_145956885415728_7585783_n.jpg?lvh=1

Then my buddy let drive his sr20 and fell in love it. So I worked my ass off throughout the winter break doing odd jobs here and there to save up for a sr and other parts for it. Then after all the hard work it paid off so nicely! Still was 16 and did my 1st sr swap alone, man did i do a shitty job.

https://scontent-a.xx.fbcdn.net/hphotos-prn1/t1/61548_163096857035064_3892979_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-prn1/t1/60858_163126103698806_3727088_n.jpg

I then blew the clutch on the sr and yes it was a ebay clutch i didnt know any better!!

https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/40158_171383979539685_3634495_n.jpg?lvh=1

https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-ash2/t1/39538_171672359510847_1684696_n.jpg?lvh=1

Tried swapping out the clutch with a local company that made them to slide at the 1st frankenslide event at cfrc. Missed it because I didn't adjust the pedal correctly and the car wouldn't go into gear. Knowing that now i felt like such a noob and felt so left out at that event )):


giW3agA0RmY

After i got the car running good is started to just load up on tires and just fucking destroy them.

https://scontent-b.xx.fbcdn.net/hphotos-prn1/t1/69527_182083681803048_3403650_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-ash3/t1/154499_177240222287394_8111736_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-frc1/t1/154389_179823748695708_609338_n.jpg

https://scontent-a.xx.fbcdn.net/hphotos-prn1/t1/76152_179523542059062_6274631_n.jpg

https://scontent-a.xx.fbcdn.net/hphotos-prn1/t1/65450_181277281883688_3040529_n.jpg

https://scontent-a.xx.fbcdn.net/hphotos-prn1/t1/69531_183067518371331_8339813_n.jpg

https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-ash3/t1/163245_184662274878522_6216622_n.jpg

https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-prn1/t1/156698_184919921519424_4205640_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/162757_185971914747558_4019959_n.jpg?lvh=1

Tried manjing down a main road and fucked everything up suspension wise on the car. The stance coils beffy as fuck were the old part on the driver side that didnt get destroyed.

https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/163664_185967244748025_4985266_n.jpg?lvh=1

https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/260095_241325382545544_4166694_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/163700_192519567426126_5028186_n.jpg?lvh=1

https://scontent-a.xx.fbcdn.net/hphotos-frc1/t1/252149_226608610683888_4883974_n.jpg

https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-frc1/t1/254305_226608630683886_1286130_n.jpg

https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-ash3/t1/252442_226608640683885_687774_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/251613_226608654017217_6830259_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-ash3/t1/249082_226608660683883_5694944_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-ash4/t1/252111_226608674017215_7359889_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-ash4/t1/250228_226608704017212_6115820_n.jpg

https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-ash3/t1/249174_226608717350544_2264109_n.jpg

https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/254778_226608730683876_4407700_n.jpg?lvh=1

https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-ash3/t1/249948_226608740683875_6191325_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/254709_226608747350541_198501_n.jpg?lvh=1

got solid rear bushings for the car to start making my suspension set-up better

https://scontent-b.xx.fbcdn.net/hphotos-prn1/t1/156717_180306135314136_2803676_n.jpg

Blew 4 transmissions it never eneded haha!!

https://scontent-b.xx.fbcdn.net/hphotos-prn1/t1/188481_205347126143370_3701497_n.jpg

https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/198854_207376322607117_7916174_n.jpg

https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/200377_208821125795970_7779917_n.jpg

[Javier13]

Last event before i tore everything down to get more power out of the t25.

Got wheels for getting straight A's my mom is awesome haha!!!
https://scontent-a.xx.fbcdn.net/hphotos-frc1/t1/189787_210781612266588_728034_n.jpg

https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/196814_211915638819852_3310067_n.jpg

https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-ash2/t1/200711_212207008790715_8274094_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/207193_214165815261501_4603665_n.jpg

My friend fucking with me when i was buying something at the store haha!!

Now i start my tear down to go external wastegate, z-maf, 560cc injectors, and 1bar of boost.
https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-frc3/t1/295987_266189316725817_3287688_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/262407_266189526725796_7530497_n.jpg

https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/205959_266189460059136_3929626_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/293500_267598703251545_634792_n.jpg

Fucking loved this set-up!!! It was so awesome to hear a external wastegate for the 1st time ever!!!!!
WZV3qSa4sBo

https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-frc3/t1/320563_275392269138855_698717_n.jpg

Made more torque than i did power on this set-up hahaha!!!!! if anyone wants more power out of their t25 this is the best route to go!!!
New Setup . - YouTube (http://www.youtube.com/watch?v=yC3eIplcWKs)

Raced my friend before we went street sliding and walked him haha (not really)
zzbuTyxGN8M
BMxvqU0-xEQ

https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/310772_273854185959330_4225804_n.jpg
I started to get more consistent with my driving and the car linking the bank entry
ps2JdvUv-3Y
mnbcUDmILOU
https://scontent-b.xx.fbcdn.net/hphotos-prn1/t1/316701_283854731625942_1419492403_n.jpg
https://scontent-a.xx.fbcdn.net/hphotos-frc1/t1/312753_283854808292601_1670044468_n.jpg
https://scontent-a.xx.fbcdn.net/hphotos-frc1/t1/301405_283854918292590_264300815_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/310131_284154694929279_233218588_n.jpg
https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-ash2/t1/317509_284155028262579_2115060098_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/293647_284154864929262_1135233953_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/309685_284155254929223_591274087_n.jpg
https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/317470_284155544929194_99710017_n.jpg

end of the day blew up the clutch on the car due to blowing up my fucking transmission had to get another transmission and clutch and this time I didn’t fucking cheap out on the clutch set-up!!
https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-ash2/t1/296744_287638684580880_144812862_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-prn1/t1/s720x720/381062_302703356407746_1892208418_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-prn1/t1/297486_292732267404855_1187900961_n.jpg
https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-frc1/t1/302564_289253674419381_733184755_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/315011_297911520220263_586460676_n.jpg
(random picture at my school with my auto teacher haha)

[Javier13]

Then I sold my coils and got myself some new fortune auto coils and they’re amazing!!!
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/320880_305147046163377_953426732_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/373950_305668152777933_883614043_n.jpg
Got new gloves for Christmas from my mom, such a bad ass mom haha!!
https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-frc3/t1/s720x720/383639_306898939321521_1544656389_n.jpg
Then saw a group buy from chaser aero on their kits and got one
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/374371_320637871280961_1728191696_n.jpg
lots of adjusting had to happen
https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/s720x720/393326_322662937745121_1529631006_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-prn1/t1/s720x720/386125_322663107745104_458077985_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/374177_322663234411758_215284170_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/390646_323923524285729_1192028020_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/374706_323923690952379_331106965_n.jpg
https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-ash2/t1/s720x720/376989_323924077619007_1328855119_n.jpg
Then I got a pit bull puppy that was about to get euthanized. PEOPLE ADOPT YOUR PETS!!!!!! Shes such a sweet dog and loves children and people!
Got tires for the upcoming event
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/385527_348083341869747_1384785909_n.jpg
Yes I drove like this for a while and eve at the event since I was trying to wrap my dash but didn’t finish on time
https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-ash2/t1/s720x720/398171_352115671466514_49337676_n.jpg
pics from the event with aero on well ½ of it on haha
https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/s720x720/417314_359985070679574_2105010278_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/401121_359985344012880_2027845623_n.jpg
https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/s720x720/405367_360618307282917_844082378_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/421178_360619413949473_1794524843_n.jpg
https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-ash2/t1/s720x720/417153_360619583949456_1319530938_n.jpg
Picture of the motor set-up
https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-ash2/t1/s720x720/425032_370173189660762_636098593_n.jpg
Then I bought a 4runner for a daily so I could save up and build the car better and man did I love the A/c haha!!
Picked up a new ebay exhaust from some dude
https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/s720x720/418106_390615320949882_1994933204_n.jpg
We cut the shit out of the fart can and welded a 3”to4” reducer and a 1’ 4” stainless
https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-ash2/t1/s720x720/419374_391776754167072_1280010947_n.jpg
It looked really rowdy and sounded so mean! And painted the aero all one color! Was loving this car so much!!!
Got more tires from tireman ybor
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/525559_396559803688767_1117445341_n.jpg
Then off to my next event loved this car so much and it drove like a dream
https://scontent-a.xx.fbcdn.net/hphotos-ash3/t1/s720x720/537173_397743796903701_1863388672_n.jpg
https://scontent-a.xx.fbcdn.net/hphotos-ash3/t1/s720x720/548341_397935620217852_1760517110_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-prn1/t1/s720x720/556410_397935866884494_1949406673_n.jpg
https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-ash2/t1/s720x720/535396_397935923551155_1078301164_n.jpg
https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/s720x720/527750_397936130217801_1011741490_n.jpg
https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-ash3/t1/s720x720/544528_397936243551123_374209038_n.jpg
qfCr9UCe7-k
Saved up a shit ton of money and bought sweet fucking gauges and made the cluster from a cnc machine and had it powdered coated.
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/546415_415303971814350_1758395175_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-ash3/t1/s720x720/578705_415970468414367_561245088_n.jpg
Then pulled out all the interior in the car while hanging out with my other dog Oreo
https://scontent-a.xx.fbcdn.net/hphotos-ash3/t1/s720x720/536104_419582308053183_170206727_n.jpg
then got a deal on a t28 from a local for 100$
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/295047_420828621261885_1768683666_n.jpg
and got a new tial qr bov.
https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-ash3/t1/s720x720/536719_431970256814388_1354229608_n.jpg
https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/s720x720/294985_432200606791353_773882813_n.jpg
After installing the new turbo went and did a burnout in my drive way haha
ziUwsixHgVc
Got the car tuned again to make sure I get everything out of this t28 on 1bar of boost
IlRiW-EbukE
Made 298hp and 305tq
After the dyno I wanted to build up my suspension for more angle
OPS knukles
https://scontent-a.xx.fbcdn.net/hphotos-ash3/t1/q77/s720x720/1017184_625048410839904_385774813_n.jpg
25mm extended control arms
https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-ash2/t1/s720x720/314800_467732749904805_209922122_n.jpg
offset rack spacers
https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/s720x720/484590_484239548254125_490762679_n.jpg
abercombie tie rods
https://scontent-a.xx.fbcdn.net/hphotos-ash2/t1/q71/s720x720/1001864_637404492937629_2001827387_n.jpg
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/486559_470382602973153_1518238361_n.jpg
Got an alignment at a buddys shop
Front: Camber -5 Toe 0 Caster 7.5
Rear:Camber -.5 Toe0
Afterwards did a little shake down before I went to events again.
dSm3P0ceVoc
Car felt awesome and even faster. I never was consistent with my set-ups. I was always changing something ever 3 months to the car. So I never go use to the new set-ups for long.
Then went to another event in the car and I fucking killed it…. Seriously!
https://scontent-a.xx.fbcdn.net/hphotos-ash2/t31/616245_481461308531949_272869097_o.jpg
album of pictures from the event
https://www.facebook.com/pedro.j.ortiz.92/media_set?set=a.481044298573650.135786.10000004252 4121&type=3
Videos from that day:
QOBeBNWvRpk
1BszH7cX8cM
BBYmPcFMWwY
Best video of the night linking the whole bank.
0yEwRbBQncQ
I fucked shit up that day, broke the inner bolt on the offset rack spacer, fucked up my intercooler and had it ziptied, blew off couplers left and right. But I had a fucking blast that day
Then I went off to school for the fall semester 300miles away. leaving the car home and drove the 4runner. I had withdrawals like crazy lol.
During school really didn’t do anything car related since I barley went home. But I did pick up a sponsor while I was gone and had my brother drive to their shows to show off my car
https://scontent-b.xx.fbcdn.net/hphotos-frc3/t1/s720x720/317986_551114548233291_2065982130_n.jpg

[Javier13]

Then after the fall semester I went on winter break and went to another event at Desoto. I slide fucking terribly, the motor didn’t have enough power to spin new 245’s on 40psi and I was just frustrated trying to feel the car. Along with that day the cage drivers went about 1000x’s more than non cage drivers so I got no seat time. Then just fed up with the motor I sold everything off. And my frined talked me into buying a 1JZ and man I was down for over a year doing this swap and commuting back and forth to school.

https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-ash2/t1/s720x720/538557_551115094899903_654545940_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-ash3/t1/s720x720/734926_551115121566567_1431789269_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-prn2/t1/p180x540/1997_551120768232669_2107287342_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-ash3/t1/p480x480/580538_551120831565996_1024284939_n.jpg

Sold everything in my car and garage sr related after the event

https://scontent-a-lga.xx.fbcdn.net/hphotos-ash2/t1/s720x720/397635_551116581566421_1663645281_n.jpg

[Javier13]

After selling everything i started to buy all the parts necessary. also re-did my cluster due to the fact that the old apexi tachometer did not read correctly and made another cluster and bought a stri 60mm tachometer

https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-ash3/t1/s720x720/537971_551115264899886_695050385_n.jpg

boxes of parts and parts
https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-frc3/t1/s720x720/321372_553865231291556_521397652_n.jpg

44mm tial
https://scontent-a-lga.xx.fbcdn.net/hphotos-ash2/t1/s720x720/304276_553865264624886_2024622930_n.jpg

holset he351 before powder coating
https://scontent-b-lga.xx.fbcdn.net/hphotos-frc3/t1/s720x720/150645_553865387958207_119999541_n.jpg?lvh=1

ebay manifold, cheap as shit and it works, but i did brace it with stainless steel rods
https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-ash3/t1/s720x720/580641_553865421291537_1965003764_n.jpg

ebay intercooler core
https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-frc1/t1/s720x720/580547_553865471291532_218800045_n.jpg

my friend welding the flange on manifold
https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-ash3/t1/s720x720/734980_554726231205456_1030663254_n.jpg

welding the wastegate flap for external set-up
https://scontent-b-lga.xx.fbcdn.net/hphotos-ash4/t1/s720x720/484727_554726267872119_586295937_n.jpg

aem 3.5 bar map sensor
https://scontent-b-lga.xx.fbcdn.net/hphotos-ash3/t1/s720x720/11158_567834429894636_1056178246_n.jpg

how the garage was for most of the time since i was at school and couldnt really work on the car
https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-frc3/t1/s720x720/65236_568074516537294_534506758_n.jpg?lvh=1

plasti dipped the car, hating it so much now cant wait to get it painted with actual real paint.....
https://scontent-b-lga.xx.fbcdn.net/hphotos-prn1/t1/s720x720/11380_568096216535124_497456373_n.jpg

t3 flange on a t4 manifold
https://scontent-b-lga.xx.fbcdn.net/hphotos-ash3/t1/s720x720/529603_568340013177411_486134337_n.jpg

powder coated rear housing on the manifold
https://scontent-b-lga.xx.fbcdn.net/hphotos-ash3/t1/s720x720/179793_568340459844033_1990618576_n.jpg

front housing
https://scontent-b-lga.xx.fbcdn.net/hphotos-frc3/t1/s720x720/404551_570944312916981_236605185_n.jpg

picked up the motor in miami while i was at school. the motor sat in the back of my 4runner for like 3 weeks haha
https://scontent-a-lga.xx.fbcdn.net/hphotos-prn1/t1/s720x720/555823_571815802829832_1559368187_n.jpg

tore it down
https://scontent-a-lga.xx.fbcdn.net/hphotos-ash3/t1/s720x720/555193_577813008896778_291141120_n.jpg

painted it
https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-ash3/t1/s720x720/11676_578124275532318_204794509_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-ash2/t1/s720x720/420349_578544902156922_758093808_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-frc3/t1/s720x720/549961_579233732088039_1446655287_n.jpg

bought real tools to start building up my collection
https://scontent-b-lga.xx.fbcdn.net/hphotos-frc3/t1/s720x720/313484_581031458574933_173825611_n.jpg

stripping everything
https://scontent-a-lga.xx.fbcdn.net/hphotos-ash3/t1/s720x720/581786_582467618431317_979455959_n.jpg

replaced everything that i could timing belt, water pump, all gaskets ect..
https://scontent-b-lga.xx.fbcdn.net/hphotos-frc3/t1/s720x720/599205_581809655163780_1016116616_n.jpg.

https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-frc1/t1/s720x720/224695_587828181228594_519886885_n.jpg

breathers for the valve cover to catch can
https://scontent-a-lga.xx.fbcdn.net/hphotos-ash2/t1/s720x720/208203_587828194561926_1112238325_n.jpg

test fitting everything
https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-frc3/t1/s720x720/552142_588074811203931_25530308_n.jpg

fuel lines all an russel shit
https://scontent-a-lga.xx.fbcdn.net/hphotos-prn1/t1/s720x720/64783_588203867857692_757781327_n.jpg

stripping interior to re-wire chassis
https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-ash3/t1/s720x720/71948_588377761173636_1742010281_n.jpg

https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-frc3/t1/p720x720/521465_588618834482862_1110030477_n.jpg.

https://scontent-a-lga.xx.fbcdn.net/hphotos-ash2/t1/s720x720/482030_588618881149524_162858073_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-ash3/t1/s720x720/561219_593911487286930_1850845796_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-prn1/t1/s720x720/529343_593911627286916_41730038_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-ash2/t1/s720x720/382989_593936193951126_305732560_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-ash3/t1/p720x720/11705_598759653468780_842401359_n.jpg

https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-prn1/t1/s720x720/601712_598759620135450_312126209_n.jpg

https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-ash2/t1/s720x720/317490_601186416559437_6329610_n.jpg

https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-ash3/t1/s720x720/945375_604181589593253_221436513_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-ash2/t1/s720x720/164199_604928456185233_54292669_n.jpg?lvh=1

https://scontent-b-lga.xx.fbcdn.net/hphotos-frc3/t1/s720x720/11786_604928529518559_1581555223_n.jpg?lvh=1

https://scontent-b-lga.xx.fbcdn.net/hphotos-prn1/t1/s720x720/943266_605119982832747_1238218450_n.jpg

https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-ash2/t1/s720x720/420725_605724146105664_1293521759_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-prn1/t1/p180x540/941012_605724196105659_489053100_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-ash3/t1/s720x720/947008_606385176039561_1837162743_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-frc3/t1/s720x720/262414_607422225935856_1801483801_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-prn2/t1/s720x720/960259_607809955897083_1401954644_n.jpg

re-did everything on the chassis harness to switchs and relays and kill swich blah blah blah
https://scontent-a-lga.xx.fbcdn.net/hphotos-prn2/t1/q71/s720x720/972299_611164862228259_1936059151_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-ash2/t1/q71/s720x720/248106_613223725355706_1695505049_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-prn2/t1/q75/s720x720/984083_613452388666173_2054119525_n.jpg

brake lines
https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-prn2/t1/q77/s720x720/6483_621337957877616_317732607_n.jpg

engine bay ready for the motor
https://scontent-a-lga.xx.fbcdn.net/hphotos-ash3/t1/q71/s720x720/1017196_623389364339142_987939889_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-prn2/t1/q73/s720x720/225814_624096410935104_1198849304_n.jpg

[Javier13]

r154 extension 3"
https://scontent-a-lga.xx.fbcdn.net/hphotos-ash2/t1/q83/s720x720/1016834_627178620626883_391884916_n.jpg

https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-prn1/t1/q77/s720x720/1010509_627178647293547_887373588_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-prn1/t1/q71/s720x720/1016596_627494007262011_1880081670_n.jpg

https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-frc3/t1/q71/s720x720/992845_627900480554697_1492794273_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-frc1/t1/q80/s720x720/1013476_629359600408785_1717059856_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-frc3/t1/q79/s720x720/969851_629431053734973_700268432_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-frc1/t1/p180x540/1044949_629714577039954_881414650_n.jpg

https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-ash3/t1/q71/s720x720/1016056_629802087031203_501645545_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-frc3/t1/q72/s720x720/998192_630096570335088_183683665_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-prn1/t1/p180x540/1010703_637391892938889_1714420269_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-ash3/t1/q79/s720x720/1185649_663981513613260_1112205963_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-ash4/t1/q71/s720x720/1377989_673591985985546_221807540_n.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-frc3/t1/q77/s720x720/1375257_688114484533296_1672542285_n.jpg

forgot to add i gave my mom my 4runner and bought my self a f350 w/ a 7.3
https://scontent-b-lga.xx.fbcdn.net/hphotos-ash4/t1/q83/s720x720/1175615_666802793331132_450079250_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-frc1/t1/p480x480/487417_697903366887741_245343419_n.jpg
https://scontent-a-lga.xx.fbcdn.net/hphotos-frc3/t1/q81/s720x720/1482828_714008101943934_793753438_n.jpg
https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-ash4/t1/q71/s720x720/1377292_689572197720858_670018245_n.jpg

uhaul trailers suck for low cars

went to the dyno and my sensors were not reading right and so i had to sort the problem with little time i had before i went back to school so i gave up on it and asked Mark Panic to make me a harness.

https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-ash4/t1/q71/s720x720/1377292_689572197720858_670018245_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-prn2/t1/p180x540/1513252_719636488047762_1124410672_n.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-prn1/t1/p180x540/1521798_720417961302948_1355211394_n.jpg

https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-frc1/t1/p180x540/64207_720425804635497_1805030835_n.jpg
the before and after haha

brother made the labels for the switch panel
https://scontent-a-lga.xx.fbcdn.net/hphotos-ash3/t1/q77/s720x720/1528599_735588529785891_684076319_n.jpg

got new tires for all my wheels
https://scontent-a-lga.xx.fbcdn.net/hphotos-ash3/t1/p180x540/1622798_736388823039195_1796003882_n.jpg

the car made awesome power and torque, and my 1st time driving it tuned blew up my diff was scary haha and locked up my rear end when i was braking. so my buddy sold me his nismo 2-way
https://scontent-b-lga.xx.fbcdn.net/hphotos-ash3/t1/q71/s720x720/1655843_736623876349023_1032415188_n.jpg

forgot to wire up windshield wipers haha
https://scontent-b-lga.xx.fbcdn.net/hphotos-ash3/t1/p180x540/1743550_737384862939591_94971018_n.jpg

forgot to put this in here but this is my high pressure power steering line from the rack to the pump
https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-prn2/t1/s720x720/969742_608524459158966_1232667037_n.jpg

driving the car around and having fun in it finally!
https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-prn1/t31/p180x540/1599286_738770029468638_395536779_o.jpg

https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-ash4/t31/p180x540/1495216_738770109468630_573516006_o.jpg

https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-ash3/t31/p180x540/1487967_738770179468623_147242708_o.jpg

https://scontent-b-lga.xx.fbcdn.net/hphotos-prn1/t31/p180x540/893111_738770206135287_2050478480_o.jpg

https://scontent-a-lga.xx.fbcdn.net/hphotos-prn1/t31/p180x540/1602139_738770406135267_1588122210_o.jpg

now im back at school getting by barley and busting my ass to finish this semester hoping that i can keep my gpa where its at lol.

https://scontent-a-lga.xx.fbcdn.net/hphotos-ash3/t1/q71/s720x720/1545080_739854326025978_1780445787_n.jpg

https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-ash3/t1/p720x720/1551584_735080019836742_1103625301_n.jpg
random pics lol

[Javier13]

Things left to do on the car as of now to make it ready for the track

mount fire extinguisher
buy a new helmet
install a new brake booster
clean up the chassis harness
check the torque on all bolts
get an alignment

then go out drifting once again!!!

[Rafi Casas]

Hey nice ride,

Im actually applying to FAU (mechanical engineering)

[Javier13]

cool dude, awesome campus, engineering isn't the best here but the classes are small so the teacher will get to know you better. As of now, my strengths of materials class has 40 students. I think at UF they had over 150 students lol

[benarovi]

nice thread. gonna drive pbir in march??

[Javier13]

im going to try, but its all about the money and if my truck wants to cooperate with me and fucking run correctly. i still need to do a shake down somewhere to get a feel for the power of the car. Its making over 100 more than my sr20det.

[benarovi]

is it registered? theres some sweet spots around. can always go to skidpad down in mia there fun to tandem me and a few friends are going to go the 22nd to practice for pbir. im super rusty lol

[xoxide]

Ben's trying to recruit everyone to PBIR hahah -_-


Glad you posted a build thread, its a lot easier to follow than your facebook album.

[Javier13]

Id only have the money for pbir. and its registered but the luxury of just having a truck and towing the car to events is just a lot more convenient. I might just hit up a local spot by my house in tampa and see how the car reacts. no problem! I'd like to help out others with suspension, and with 1jz swaps. yea my fb build is everywhere haha

[Oakville]

Nice car man. Im in deerfield beach quite a bit, you have this car with you up in boca?

[Javier13]

No my car is my home in tampa, i go to school in boca. But I do plan to trailer the car down for local events around the Boca Raton area.

[benarovi]

Ben's trying to recruit everyone to PBIR hahah -_-


Glad you posted a build thread, its a lot easier to follow than your facebook album.
because they dont have enough people to go so they stopped. its 20 min from my house, the last time i drove it, there were maybe 7 people driving including me. yea you get alot of seat time but its more fun with more people. tracks sick, just paved, no bumps anywhere and its good on tires.

[Javier13]

i need $480 to be able to run that day, thats for my plane ticket home, diesel for the truck, fuel for the car, trailer rental, alignment, diesel back, and plane ticket back to school lol. Ill try my hardest i have $130 to my name right now.

[KravingAKouki]

Uhaul trailers are terrible for low cars. The wheel tracks have the angled "lip" pieces in the middle, and will pinch the frame rails. I had to try the wooden blocks as well, and it was terrible. Better off investing in a trailer at this point. Never looking back, and they could be had at a deal if you are looking thoroughly. Love the car, keep it up!

[Javier13]

Thanks dude, and ill get one once i get a job over the summer, or a internship. And for the future when money is good heres what i plan on getting done
-Cosmis MRII and S5R's or some wheels with lip
-over fenders
-crash bars
-bolt in cage(I'm never going to do Pro-Am or crap like that. I just want to tandem at local events and have fun!)
-isis dual 4" exhaust
-326 power wing(some knock off one since im cheap)
-bride reps(Sprint 5 sparco seat sucks but does a bad ass job)
-PBM rear drop knuckles(car is super low and want to make the geometry of my arms, and axle as level as possible!)
-dual caliper set-up (With a pbm hydro with wilwood reservoir, my own lines, and wilwood calipers)
-repaint the car red, i hate plastidip so fucking much i tolerate it because my brother paid for everything and even sprayed it but never again.

[xoxide]

Tell me about Uhaul trailers -_-
http://i82.photobucket.com/albums/j259/sprinter1/IMAG0242_zpsa169e5a2.jpg


Im going to try and make PBIR Ben, but unless my car is running prime and I have a cage im not making that far of a trip to drift alone all day lol

[Javier13]

i said fuck it and just jacked my car onto the trailer and pushed it with 5 people haha. the car is going to go into a wall one day and my frame is already FUBAR

[BiG MiKE86]

nice! lOVE this build

[Javier13]

thanks for checking it out!!! I'll be sure to update as much as possible. Nothing really much to do to the car except take it to events and work out what ever bugs come my way with it.

[d_nice]

looks good bro

[Javier13]

pretty terrible news, so i owe my school money a lot. so i won't be able to go to any events for a while........ sucks but shit happens. if im able to sell my spare wiring harness and some other things in my garage that i dont need then i would be good. so does anyone need a jza70 1jz wiring harness uncut?

[badass8]

Damn good work. Love the tow truck by the way.

Do you have a run down on whats needed for a 1jz swap?

I originally planned to do 1uzfe swap because its different and its a great motor but thinking to shovel out some extra cash and do a 1jz swap and not sure where to find a run down of whats needed.

[Javier13]

everything is posted on the list on the first post. like everything that i can think of.

but ill post here also,
wiring harness conversion
extension for the transmission 3"
motor mount brackets from xcessive or any company
hit the trans tunnel out to fit starter and what not
driveshaft
intercooler piping
exhaust
its just like an sr swap necessities or any motor swap for that matter.

[CoupedupRB]

Read it.

Like it.

[JAWWWDEN]

What's your cooling setup? I'm in the process of doing a Vvti 1j and hearing people say there impossible to keep cool.

[Javier13]

what i have are two pull fans at 2800cfm, water wetter, distilled water, new water pump, isis radiator for a sr, oem thermostat, and silicone hoses. my temps driving around and beating on the car were around 190~200F. on the dyno and doing continuous passes the car was at 220~230F (but there wasn't a lot of water in the system because I didn't flush it correctly). I also have a mid mount intercooler which i pan on putting two more 10" fans. along with a oil cooler and ps cooler up front.

[JAWWWDEN]

Cool thanks a buddy of mine couldn't get his to stay cool and ended up buying a huge triple pass nascar style radiator but I don't wanna do that

[Javier13]

yeah just do my set-up and you should be fine. but i would get a colder thermostat so it can open up earlier and keep the temps down. which ill probably do along with a swirl pot so i'll never over heat. JZ's run hot so its best to take the measures and spend the cash so it last.

[FuckWasted]

Damn Looking Sick.
Keep It up.

[Javier13]

Thanks dude ill keep this updated as much as possible! next weekend ill be home and will be working some things out with the car

[h2v7]

so you dont like front bumpers huh

[Javier13]

never! my car would look 100x better but id probably would have it explode on me just driving around in tampa and I don't have the time to play with that lol. also my car is low enough where i can't fit vans under the side skirt so the front bumper would be destroyed the first day i have it on.

[aga]

but i would get a colder thermostat so it can open up earlier and keep the temps down.

that won't do any difference at all because your thermostat is already open.. . save money, get bigger radiator.

[Javier13]

thanks for that, and i already have a isis radiator which is 3 a row. and my temps are perfect right now but i don't know how itll do when i go to an event.

[sneakypete]

Awesome man. I'm starting the process of swapping a 1j here soon. This is definitely helpful. One thing I didn't see here, was a front sump. I've seen a lot of other builds with it and was curious about it. As where they got it from. I'm hearing a lot of people get them from the aristo's. Any input?

Sent from my SPH-L720 using Tapatalk

[Javier13]

i have a jza70 motor which was rear sump but i had them swap it to the soarer front sump. just look around ebay or supra forums and youll find one! let me know if you need any other assistance!

[sneakypete]

Okay cool man! Appreciate it, I live down in St. Petersburg so just the bridge away from you I believe

Sent from my SPH-L720 using Tapatalk

[Kwolfe]

Sweet build, can't wait to put my 1jz in!

[Javier13]

Okay cool man! Appreciate it, I live down in St. Petersburg so just the bridge away from you I believe

Sent from my SPH-L720 using Tapatalk

yeah sneakypete, but im in boca i dont go home as much as i did anymore since i finished the car so i can focus on school.

[Javier13]

Sweet build, can't wait to put my 1jz in!

as i have posted in my 1st post if you need any help email me or post on here. JZ's are the shit will never go to any other motor.

[Javier13]

not a update but just many random pictures over the 5 year course ive had the car lol

https://scontent-a-atl.xx.fbcdn.net/hphotos-ash3/t1/60505_1391733435637_1837484_n.jpg

All my local tampa friend. Sean Forester purple silvia with hippo sleak aero, Tyler Chewning (who owns odyssey parts shop the white 240sx), my buddy K.T. with the grey s14, and my car in the back because i blew up my welded diff haha, and this was the day of my birthday is the occasion of everyone over my house lol.
https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-prn1/v/t1/40955_1372620717831_7242095_n.jpg?oh=b72e7fd6a05d4 4b863cfe4bd27296b15&oe=538EA2FF&__gda__=1401299138_06c719d4969b3cf751b71424d817a72 4

Formula D driver Pat Goodin driving my car this is back in 2009~2010 he killed it in my dual cam KA and you see me in the back with the white T to the left
https://scontent-a-atl.xx.fbcdn.net/hphotos-ash3/t1/59326_140223099355665_3753141_n.jpg

https://scontent-b-atl.xx.fbcdn.net/hphotos-prn1/t1/62815_163398157005831_4350223_n.jpg

haha a welded diff that my buddy Mike Ranlet did for a local kid
https://scontent-b-atl.xx.fbcdn.net/hphotos-prn1/t1/74040_457442404462_5967602_n.jpg

my s13 with Christmas light on going home from a christmas event day at desoto
https://scontent-a-atl.xx.fbcdn.net/hphotos-prn1/t1/156956_184199394924409_1626867_n.jpg

https://scontent-a-atl.xx.fbcdn.net/hphotos-ash2/t1/163870_185335444812102_5604007_n.jpg?lvh=1

https://scontent-b-atl.xx.fbcdn.net/hphotos-frc3/t1/26453_119462484732732_979749_n.jpg?lvh=1

https://scontent-a-atl.xx.fbcdn.net/hphotos-ash2/t1/165570_185397714805875_6391210_n.jpg?lvh=1

https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-prn1/t1/157017_175500889149952_6254321_n.jpg

https://scontent-b-atl.xx.fbcdn.net/hphotos-frc3/t1/183053_200704563275190_3719463_n.jpg

https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-prn2/t1/180030_200699873275659_6677497_n.jpg

https://scontent-a-atl.xx.fbcdn.net/hphotos-ash3/t1/62033_163372730341707_7728777_n.jpg

https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-frc3/t1/199181_205030472842599_409677_n.jpg

https://scontent-b-atl.xx.fbcdn.net/hphotos-frc3/t1/190446_205030396175940_4514799_n.jpg

https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-prn1/t1/189775_205062459506067_718368_n.jpg

https://scontent-a-atl.xx.fbcdn.net/hphotos-ash2/t1/184729_205062296172750_2269972_n.jpg

https://scontent-a-atl.xx.fbcdn.net/hphotos-frc1/t1/205437_214334128578900_6161908_n.jpg

https://scontent-b-atl.xx.fbcdn.net/hphotos-frc3/t31/s720x720/621010_10151141954947779_695921049_o.jpg

https://scontent-b-atl.xx.fbcdn.net/hphotos-ash3/t1/556974_4567904885485_1090243175_n.jpg

https://scontent-a-atl.xx.fbcdn.net/hphotos-ash2/t1/304656_10151072889473983_1098024557_n.jpg

https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-ash2/t1/s720x720/250742_381204475281433_240100003_n.jpg

https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-frc1/t31/s720x720/664688_217942411673516_109384563_o.jpg

https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-prn1/t31/s720x720/331661_217942761673481_24507892_o.jpg

https://scontent-b-atl.xx.fbcdn.net/hphotos-prn2/t31/s720x720/706194_217943108340113_1606475588_o.jpg

https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-prn1/t31/s720x720/257172_217943151673442_479095192_o.jpg

https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-ash2/t31/p180x540/737084_549169598428683_2121432321_o.jpg

https://scontent-a-atl.xx.fbcdn.net/hphotos-ash2/t31/p180x540/740866_549169701762006_758731975_o.jpg

https://scontent-b-atl.xx.fbcdn.net/hphotos-prn1/l/t1/q71/s720x720/994296_644854782209880_40525573_n.jpg

https://scontent-a-atl.xx.fbcdn.net/hphotos-prn1/t1/q71/s720x720/994805_645122032183155_78866163_n.jpg

[Javier13]

Also this is my favorite mobile suit Kshatriya from Gundam Unicorn so much bad ass and its piloted by a Women too.

http://img1.wikia.nocookie.net/__cb20130331163829/gundam/images/thumb/2/2d/Nz-666.jpg/1000px-Nz-666.jpg

and a random epic battle pic between Char and Banagher
https://scontent-a-atl.xx.fbcdn.net/hphotos-ash2/t1/407062_337636112914470_493379560_n.jpg

[sneakypete]

The 5.9 cummins motor is the holset hx35 right? For sure looking into it. Around what rpm range does it start building boost and hit full boost?

Sent from my SPH-L720 using Tapatalk

[Javier13]

no i dont know what the hx35 came from, but give me a couple days and ill let you know. I do know the he351 came from 02-05 dodges 5.9 i think. and ill stick a go-pro in the car to see all my gauges because i dont know either lol.

[sneakypete]

Haha okay rad. Sorry for all the questions, just looking to get a sold baseline before I go full steam. I saw you got the motor from jdm of Miami? Reasonably priced?

Sent from my SPH-L720 using Tapatalk

[Javier13]

i got it from jdm miami and i told them lets make a deal. I told them that I dont need the twins, auto trans, ecu, came without TB or flywheel, and they can kept the rear sump which all saved me money and i got the whole set-up with a r154 for $2000. Which was cheaper than my sr20!!! If i stuck with everything stock this swap would have been a lot cheaper than my sr20 swap and made a lot more reliable power for cheaper. but i decided to go for reasonable 400hp and i achieved it but ended costing more since i went with quality parts so i dont need to upgrade in the future. only thing i can upgrade on now is just my fuel system.

and for the hx35 for look cummins trucks around 95-99 12v's

[schoja]

Alltogether about how much do you think it costed for the 1jz swap?

[supersayianjim]

Also this is my favorite mobile suit Kshatriya from Gundam Unicorn so much bad ass and its piloted by a Women too.

http://img1.wikia.nocookie.net/__cb20130331163829/gundam/images/thumb/2/2d/Nz-666.jpg/1000px-Nz-666.jpg

and a random epic battle pic between Char and Banagher
https://scontent-a-atl.xx.fbcdn.net/hphotos-ash2/t1/407062_337636112914470_493379560_n.jpg



sorry but gundam 00 raiser is way better.

https://www.youtube.com/watch?v=epVpOGlp-Fo

[supersayianjim]

interesting thread op. 2 things.

-why didn't you just buy a t3 manifold in the first place??

-did you change out the oil pump??

and are you interested in buying some usdm tt injectors on the cheap??

http://i495.photobucket.com/albums/rr317/supersayianjim/misc/550ssale1_zpsabd1f1aa.jpg

[Javier13]

Alltogether about how much do you think it costed for the 1jz swap?

Well I lost count after i bought my AEM lmao which was 7000$. But I went the full nine yards on the motor so I wouldn't need to do anything for a while. For a bone stock swap you could do it for 3500-4000

[Javier13]

sorry but gundam 00 raiser is way better.

https://www.youtube.com/watch?v=epVpOGlp-Fo

Gundam 00 Raiser just doesn't do it for me like the Zaku does haha!!!

[Javier13]

interesting thread op. 2 things.

-why didn't you just buy a t3 manifold in the first place??

-did you change out the oil pump??

and are you interested in buying some usdm tt injectors on the cheap??

http://i495.photobucket.com/albums/rr317/supersayianjim/misc/550ssale1_zpsabd1f1aa.jpg

I didn't get a t3 manifold because I just went with the cheapest manifold i could find on ebay and a buddy already had a bunch of t3 flanges at his shop.

And no i didn't change the oil pump out. That's the only thing I did not change on the motor. But the Oil pressure is on point so there's no need.

And I wish you offered those 550's to me a year ago haha!!! Motor is already tuned for 440's.

[sneakypete]

You having any rubbing issues with the sikky sway bar and angle mods? I have pbm knuckles and am leaning towards the sikky sway bar.

Sent from my SPH-L720 using Tapatalk

[Javier13]

yea i hit the crap out of the bar lol, and i have the farthest setting back on the sway bar. i have knuckles, extended control arms, offset rack spacer everything for angle mods.

[sneakypete]

Yeah I'm going to get the whiteline one. It's designed around angle mods and works for the swap.

Sent from my SPH-L720 using Tapatalk

[Javier13]

both are good dude, i just liked the sikky one since ive seen it on many jz setups with out any issues. And sikky is a bad ass company on top of that

[Javier13]

My last day before i go back to boca raton for school I drove the s13 a shit ton all over tampa. Did some street sliding session and the car felt amaing and so responsive. Seriously do not need the power of what this car is making to drift what so ever.

https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-frc1/t1/p180x540/1959636_758149914196419_1438667670_n.jpg

https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-ash3/t1/p180x540/1653505_758074160870661_1731812951_n.jpg


https://scontent-a-dfw.xx.fbcdn.net/hphotos-prn2/t1/p180x540/603444_757973480880729_1662518994_n.jpg

https://scontent-b-dfw.xx.fbcdn.net/hphotos-prn1/t1/q71/s720x720/1966714_757973040880773_299871996_n.jpg

Buddy at Odyssey Fabrication making a honda b-series turbo manifold with A/C. This dude makes rowdy ass parts and is an amazing fabricator!!!

https://scontent-a-dfw.xx.fbcdn.net/hphotos-prn1/t31/p180x540/1009542_762645490414425_1174826646_o.jpg

https://scontent-b-dfw.xx.fbcdn.net/hphotos-prn2/t31/p180x540/1798917_762663183745989_80583035_o.jpg

https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-prn2/t31/p180x540/1799901_762662793746028_60104033_o.jpg

https://scontent-a-dfw.xx.fbcdn.net/hphotos-ash3/t31/p180x540/1614377_762662097079431_1265753846_o.jpg

https://scontent-b-dfw.xx.fbcdn.net/hphotos-frc1/t31/p180x540/1781563_762661230412851_170528212_o.jpg
https://scontent-a-dfw.xx.fbcdn.net/hphotos-ash3/t31.0-8/p180x540/1888963_762648290414145_1462118023_o.jpg

https://scontent-a-dfw.xx.fbcdn.net/hphotos-prn2/t31/p180x540/1655017_762647163747591_264725793_o.jpg

https://scontent-b-dfw.xx.fbcdn.net/hphotos-frc3/t1/10001296_757335260944551_390922689_n.jpg

https://scontent-a-dfw.xx.fbcdn.net/hphotos-frc1/t1/p180x540/1964830_757151054296305_382570871_n.jpg

[Javier13]

My buddy at Odyssey Parts Shop made my brother a rowdy exhaust for his Hyundai Genesis

https://scontent-a.xx.fbcdn.net/hphotos-frc1/t1/1979477_759785834032827_2107766181_n.jpg

https://scontent-a.xx.fbcdn.net/hphotos-ash3/t31/q71/s720x720/1932582_10202531886071012_1769386815_o.jpg

https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-prn1/t1/1965014_759785894032821_923220490_n.jpg

https://scontent-b.xx.fbcdn.net/hphotos-frc3/v/t1/q71/s720x720/1959241_759820497362694_1374859744_n.jpg?oh=2e2f65 413f6e4ead9ae23634e7f9056c&oe=53AA615F

and little more pics from spring break that my buddy took

the bolt that was holding up my head lights fell off on the highway going to st pete for a frs meet, and then zip tied it and then again fell off then need just had zip ties to hold it up lmao

https://scontent-b.xx.fbcdn.net/hphotos-frc1/t1/p296x100/1779841_758228300855247_871647308_n.jpg

https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-prn2/t1/p296x100/1947878_758228250855252_928058857_n.jpg

and my buddy with the frs gave me an awesome idea this will be coming soon
https://scontent-a.xx.fbcdn.net/hphotos-ash3/t1.0-9/p526x296/993027_778108868867496_657923255_n.jpg

and a video my cousin made from me doing shake down runs in my car
MVblnjXGdQc

the car may sound laggy but its not i was babying the throttle in the 1st part of the video.

[BiG MiKE86]

Car sounds sooo good!

[Javier13]

Thanks dude! i still need to make an exhaust when i get back home. Ill be doing the same exhaust setup as my brother 3" and 4" tip which i had last time for my sr sounded nasty. Can't wait to hear it with a jz!!!

[BiG MiKE86]

Nice - should be a sweet sounding car

What part of SFL you from btw?

[Javier13]

My dually and 240 are in Tampa, but I live in Boca Raton for school

[BiG MiKE86]

Word. I work up in Deerfield Beach. Hopefully I'll be driving my car up here soon (2jz S13)

[Javier13]

yeah i saw your build thread looks rowdy dude! Love to see the final product. And i plan on doing events not now since im dead broke,

[conrad_s13.5]

shit sounds great,. and looks fun

bout all thats important to me....lol

[Javier13]

thanks dude, i really need to get more seat time when the money is there so i can improve my skill!

Also forgot to metion i got an alignment at a buddies shop

my specs i run are

front: camber: -5
caster:7.5
toe: factory

rear: camber:0 should make it a little more positive for squating
toe: factory

[BiG MiKE86]

yeah i saw your build thread looks rowdy dude! Love to see the final product. And i plan on doing events not now since im dead broke,
Thanks man - should be done soon! See you at the events :coold:

[Javier13]

same to you but i dont think ill be going to events till i graduate when i actually have a job and some sort of income lol. next two years are going to be hell lol

[shinhed]

You're one ambitious mofo! Keep it up!

[Javier13]

thanks dude ill keep up the hard work! the car just needs to be driven and stock up on tires for the future. Happy you enjoyed the build thread

[Kwolfe]

Sounds fucking amazing!

[Javier13]

Thanks for looking at the build thread!

[Javier13]

been getting a lot of email of people wandering about the swap keep em coming i try to answer them as fast as possible!

[Javier13]

9NpI9AIHJAw

Blew up my nismo two way last night had to tow the car back with my buddys dually at 1am in the morning. Im out of money like 20$ in my account.... So I won't be playing with cars for a while:/

[Javier13]

https://scontent-a-mia.xx.fbcdn.net/hphotos-ash3/t1.0-9/q80/s720x720/10171870_768236716521072_2130555396_n.jpg

Also threw this on the kill switch to make my interior more to my liking lol

[Javier13]

Harness done by MARK PANIC WIRING:

https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-frc1/t1.0-9/p180x540/64207_720425804635497_1805030835_n.jpg

https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-prn2/t1.0-9/p180x540/1493221_720417974636280_1230082472_n.jpg

https://scontent-a-mia.xx.fbcdn.net/hphotos-prn1/t1.0-9/p180x540/1521798_720417961302948_1355211394_n.jpg

https://scontent-a-mia.xx.fbcdn.net/hphotos-ash3/v/t1.0-9/p180x540/1528691_720417934636284_625665316_n.jpg?oh=2e984fc e30c48117ab9002912b70e23c&oe=53A09B64

https://scontent-a-mia.xx.fbcdn.net/hphotos-prn2/t1.0-9/p180x540/1538806_720417921302952_587722827_n.jpg

https://scontent-a-mia.xx.fbcdn.net/hphotos-ash3/t1.0-9/p180x540/933918_720417904636287_1347803787_n.jpg

https://scontent-b-mia.xx.fbcdn.net/hphotos-ash4/t1.0-9/p180x540/1475984_720417877969623_89521271_n.jpg

https://scontent-b-mia.xx.fbcdn.net/hphotos-frc3/t1.0-9/p180x540/1499443_720417854636292_477722510_n.jpg

https://scontent-a-mia.xx.fbcdn.net/hphotos-ash3/v/t1.0-9/p180x540/1503855_719636518047759_12828450_n.jpg?oh=3cd85e6c 2f92c3f8f9aa45510ea88cca&oe=53A1A15E

https://scontent-a-mia.xx.fbcdn.net/hphotos-prn2/t1.0-9/p180x540/1513252_719636488047762_1124410672_n.jpg

[Javier13]

3lwj4PxircM

https://scontent-a-mia.xx.fbcdn.net/hphotos-ash3/t1.0-9/p180x540/1897966_770703732941037_615360510602940950_n.jpg

[Javier13]

Bho7zVePGuQ

I never drive this car like bitch lmao

LQF63QI_PEY

YMbd8KPbrAU

[Javier13]

https://scontent-b-mia.xx.fbcdn.net/hphotos-prn2/t1.0-9/p180x540/1557694_777516355593108_9022274582879713073_n.jpg

https://scontent-b-mia.xx.fbcdn.net/hphotos-frc3/t1.0-9/p720x720/1660362_778172785527465_1982870024363567451_n.jpg

https://scontent-a-mia.xx.fbcdn.net/hphotos-frc3/t1.0-9/p180x540/1509753_778176185527125_5818635932512096202_n.jpg

https://scontent-a-mia.xx.fbcdn.net/hphotos-prn2/t1.0-9/q86/s720x720/1511914_780320108646066_2029597580946233043_n.jpg

https://scontent-b-mia.xx.fbcdn.net/hphotos-prn2/t1.0-9/p180x540/10276982_783943451617065_1457728372558981505_n.jpg

https://scontent-b-mia.xx.fbcdn.net/hphotos-prn1/t1.0-9/p180x540/1014466_784021224942621_2274600750240887585_n.jpg

https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-prn2/t1.0-9/p180x540/10298990_785016184843125_3022119115460532865_n.jpg

https://fbcdn-sphotos-g-a.akamaihd.net/hphotos-ak-frc3/t1.0-9/p180x540/10153790_785979044746839_6973212608815790871_n.jpg

https://scontent-b-mia.xx.fbcdn.net/hphotos-prn2/t1.0-9/p180x540/10264888_786128171398593_4452112176350846382_n.jpg

https://scontent-b-mia.xx.fbcdn.net/hphotos-ash4/t1.0-9/p180x540/10291791_786128184731925_55805533501465446_n.jpg

https://scontent-b-mia.xx.fbcdn.net/hphotos-prn2/t1.0-9/p180x540/10336849_786128198065257_5139345589515332266_n.jpg

https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-frc1/t1.0-9/p180x540/10255014_786128211398589_3626436379465305912_n.jpg

https://scontent-a-mia.xx.fbcdn.net/hphotos-frc3/t1.0-9/p180x540/10269525_786618584682885_6868848621475229297_n.jpg

https://scontent-b-mia.xx.fbcdn.net/hphotos-ash4/t1.0-9/10173663_789760224368721_5782857870625412936_n.jpg

https://scontent-a-mia.xx.fbcdn.net/hphotos-prn1/t1.0-9/q84/s720x720/10348212_787175767960500_6908876183270845287_n.jpg

https://scontent-b-mia.xx.fbcdn.net/hphotos-frc1/t1.0-9/10250211_789760917701985_8594532851790780587_n.jpg

https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-prn2/t1.0-9/10297893_789761361035274_9181858955651110477_n.jpg

https://scontent-b-mia.xx.fbcdn.net/hphotos-prn2/t1.0-9/q82/s720x720/10250153_790371730974237_3041904166688932778_n.jpg

https://scontent-a-mia.xx.fbcdn.net/hphotos-ash3/t1.0-9/q82/s720x720/10365828_790371754307568_1677689356699661090_n.jpg

[Kwolfe]

WTF, a piece of your floor ripped out?

[xHeavySS]

looks like a skidplate

[Javier13]

WTF, a piece of your floor ripped out?

Yea it was when i dirt dropped out of my neighborhood i think. The car probably will not be allowed for competitions now because of it when i get a cage. Unless i repair it somehow lmao. But the hole is bigger than my fist haha

[Javier13]

looks like a skidplate

My skid plate does work for me haha thank Xcessive Manufacturing~!

[Javier13]

3_leO68-aBU

[smokescreen240]

3_leO68-aBU

clean pass good sir!

[Javier13]

Thanks ^.^

[czerwizz]

How do you like the holset? I heard it was either on or off. theres like a 100 rpm difference between 0psi and then 18+psi?

[vJilly]

I just wanna know where you got all this money... lol

[Javier13]

I just wanna know where you got all this money... lol

Sold everything off my SR20 here on zilvia. Worked at my uncles mechanic shop $10 an hour and how ever many hours I wanted. Also pick up scrap metal, do landscaping in a wealthy area in Tampa, deliver large items such as grills, furniture, ect. with the truck, and random mechanic work I do at my house.

[Javier13]

How do you like the holset? I heard it was either on or off. theres like a 100 rpm difference between 0psi and then 18+psi?

Holset's are cheap, heavy, indestructible, and spool pretty quick with my experience and the response is pretty good. Full boost around 3850 rpm roughly w/ short intercooler piping, and stock motor.

[czerwizz]

Did you make it a hybrid or is it a stairght up HX, I heard the Hy was better?

[czerwizz]

Have you thought about using the HE351cw? heard it was the best holset for the 2.5L's

[sneakypete]

Know any local dudes selling an r154? That doesn't want a million dollars haha. I'm out of St. Pete and everyone wants 1500-2k...

Sent from my SPH-L720 using Tapatalk

[Javier13]

Did you make it a hybrid or is it a stairght up HX, I heard the Hy was better?

It's just a straight He351 didn't change any Thing on It

[Javier13]

Know any local dudes selling an r154? That doesn't want a million dollars haha. I'm out of St. Pete and everyone wants 1500-2k...

Sent from my SPH-L720 using Tapatalk

Tyler ChewnIng. Message me for his number

[Javier13]

https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-xpa1/v/t1.0-9/q85/p180x540/10553621_827696200575123_8788835282384757464_n.jpg ?oh=136cec4c121b9b8a87f4876792384f99&oe=54D97E7F&__gda__=1424202361_5fe5c18d640b5387960b719557b3dfe dhttps://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-xfp1/v/t1.0-9/p180x540/10565164_837549326256477_5401554887202182757_n.jpg ?oh=43563c340c82a5241020b947a16d92ab&oe=551B1744&__gda__=1424917108_e4e8b68d5a9c58c32308b96b9674d5f 3https://fbcdn-sphotos-d-a.akamaihd.net/hphotos-ak-xpf1/v/t1.0-9/s720x720/10551037_837552929589450_8444316949130824453_n.jpg ?oh=7f8d0a1805c90c762afb045f1948649c&oe=54D91229&__gda__=1423461268_535d8a551e201556b33687ae456bb11 1https://scontent-b-mia.xx.fbcdn.net/hphotos-xpf1/v/t1.0-9/p180x540/10689808_858690544142355_2381752934204916887_n.jpg ?oh=ed61239be027ede604953a887b98c2be&oe=54D6DF3Chttps://scontent-a-mia.xx.fbcdn.net/hphotos-xpa1/v/t1.0-9/p180x540/10458457_871190992892310_8264526662611723125_n.jpg ?oh=6365564f2f843d5abb58bb0e647bb4d0&oe=551DDA72https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-xpa1/v/t1.0-9/p180x540/10309030_871708059507270_7217357347143031075_n.jpg ?oh=ac9e63d497b4a9565d95ceab01e00939&oe=54E72F9F&__gda__=1424645241_fb2ec4dbb774de8b03a5dea49416e9a 8https://scontent-b-mia.xx.fbcdn.net/hphotos-xap1/v/t1.0-9/p180x540/10712819_872138019464274_4837626091420853847_n.jpg ?oh=63cc2dfb7bda29a75b0f7c3c8ccc5c7f&oe=54E94EEAhttps://scontent-a-mia.xx.fbcdn.net/hphotos-xap1/v/t1.0-9/s720x720/10382625_879853785359364_372233585517939134_n.jpg? oh=86a9721b6d6dce004a4d3c0f91db9e5d&oe=54E1A9CC

[vJilly]

is my favorite 1j car back?!

[Javier13]

is my favorite 1j car back?!

I've been at school for 2 months. I haven't gone home at all, so i decided to just dump a bunch of pics that i had laying around. But my fuel pump wiring caught on fire. So during my winter vacation december 10th. I plan to tear the wiring harness down and re-do it all over.

[Javier13]

I'll probably do some sort of walk-through on how to do chassis harnesses. Showing the engineering(current affects the gauge of wire with length, size fuse to run in a certain application) behind it and blah blah blah.

[vJilly]

hell yeah! what the fuck kinda app is it where you add those jdm as fuck animals to your pictures lol

[Javier13]

hell yeah! what the fuck kinda app is it where you add those jdm as fuck animals to your pictures lol

No idea, my asian friend has it and just sends them to me. I have no apps on my phone except a manga reader lol.

[Javier13]

Harness that I'm working on for Formula SAE car for my school.

https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-xfp1/v/t1.0-9/p180x540/1546190_894067640604645_8464368399144968611_n.jpg? oh=204a98d869da1991305691632c5e36cd&oe=54DF2E11&__gda__=1426981475_a433d116dd6bbccf531c7c40b2961a9 a

https://fbcdn-sphotos-b-a.akamaihd.net/hphotos-ak-xap1/v/t1.0-9/s720x720/10409597_894067670604642_1214784022504362485_n.jpg ?oh=735665c38946f38ae2b223206936e52e&oe=551B9E80&__gda__=1426659038_f588b6e403ecd0bf5e986cc7644956b 7

https://scontent-b-mia.xx.fbcdn.net/hphotos-xap1/v/t1.0-9/10156157_894297240581685_1083767308174917176_n.jpg ?oh=c6f76fc8d3f0da7cbacf21d51bfc010b&oe=5515992E

All Mil-spec wire, Deutsch connectors where it's needed, Mil-spec bulkhead connector that will also will be going in. Will take pics of the final product once I'm done with it. Which won't be till after my finals are done.

[Hoonigan19]

sick sick man!!

[HypnoFish]

Harness work looks good!

[Javier13]

Thanks for the comments, I plan on re-doing my drift cars chassis harness during winter break. Where I'll explain everything that is need for a street drift car on this build thread so look forward to it. I'll also will give some background of Physics 2 with Power, current, voltage, and what not.

And as well as to finishing the FSAE harness will be done during the winter break for me.

[HypnoFish]

Ive been thinking of making a new chassis harness for mine after i pick up a spare one, so ill look forward to your work this winter.

[Javier13]

Old picture from the summer before going into staging.
https://scontent-a-mia.xx.fbcdn.net/hphotos-xap1/v/t1.0-9/s720x720/10801652_898309260180483_1284250114789117095_n.jpg ?oh=d5d478b060b2a5e31a014218248e0b10&oe=5501437C

new picture how the car sits at the moment. Lost a hood pin at the track because it became loose. and the car just needs to be repainted at macco, or re sprayed red in my garage. I fucking hate plasti dipped especially when I work on the car constantly making changes here and there and getting dirty. And i need to raise the transmission it sits way to low because of the xcessive manufacturing trans mount bracket. They offered to make me spacers to raise it but I have yet to respond to them in over a year because i made my own.
https://fbcdn-sphotos-e-a.akamaihd.net/hphotos-ak-xpa1/v/t1.0-9/p180x540/1526247_897292230282186_9150522944379717648_n.jpg? oh=ff4e1394152bd8f12f2b721ab994bd3d&oe=551D57FA&__gda__=1423242285_c949c855ca64aec79a4c081b400ae65 4

Anyways, my buddy with the frs you see in the back ordered coils, hks bride seat, vertex wheel, and soon control arms. So i'll be busy after final wrenching on this thing. Can't wait to see this car with a proper suspension set up and him to start going to the track and street sliding with me.

[HypnoFish]

I have an xcessive bracket for mine as well and it seems to sit just fine. maybe an updated design?

I cannot wait to get my swapped hatch driving.

[Javier13]

SNHbQldUPIk

[xpinoyxmk]

Looks good man!

Hearing your vid makes me want to pick up a jzx90 mark ii. Still not too sure if I want that or a 180sx though.

Btw, I'm in Japan now hahaha.

[Javier13]

what dude!!!! no wonder i havent heard anything from you!! How is it over there?!?! And I'd say to pick up a jzx90. Fuck s-chassis unless its a s15 lol.

[sneakypete]

Debating on going stand alone...More info on what you're using?

[Javier13]

GM IAT Sensor
AEM 3 bar map
No IACV (sucks when cold because car likes to die when not warmed up. Did it to minimize sensor/wiring and just shit that can taken off. Car is street driven but not a daily so it doesn't bother me as much.)

Stock sensor other than those listed above.

And a AEM V2 from driftmotion. Which is a honda box, but you can use what ever standalone as long as it is pinned correctly and that it has a good map (pay a tuner if you don't know what you're doing)

[KAs14slider]

I am about to get the driftmotion aem v2. How do you like it? Has the repinned honda box been good to you? Any problems?

[Javier13]

Zero issues with my setup, but the only thing is that i deleted the IACV so it has a hard time staying on when cold. So I have to hold the throttle open for 5 minutes before driving.

[KAs14slider]

Good to hear, I still have my IACV. Hopefully I will be happy with the driftmotion setup. Also, just curious. Where did you choose to install the GM IAT sensor?

[Javier13]

Good to hear, I still have my IACV. Hopefully I will be happy with the driftmotion setup. Also, just curious. Where did you choose to install the GM IAT sensor?

I just tapped the hole where the original IAT sensor goes. seriously just got a tap and forced it. Threads on nicely just be sure to have teflon tape for precautions.

[Javier13]

Well i just noticed that none of the pictures are showing up now. This is a pain in the ass..... But I'll go back a fix all of it with time.

[Javier13]

https://scontent-a.xx.fbcdn.net/hphotos-xap1/v/t1.0-9/p180x540/10846488_908075325870543_4134791280656438005_n.jpg ?oh=9680e369d6208355b8253e95aeeede1e&oe=552A53B2

https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-xpa1/v/t1.0-9/p180x540/10897966_917673918244017_5039907148891542374_n.jpg ?oh=86ef2ca3421414af802384593b050fdf&oe=5523BEB2&__gda__=1429653844_ae27e1d6fc2111ce3999c273cc033e5 d

https://fbcdn-sphotos-a-a.akamaihd.net/hphotos-ak-xfa1/v/t1.0-9/p180x540/10882333_917673958244013_8109062258534748327_n.jpg ?oh=732b738637f400c8f650b5416c062203&oe=5569F8C3&__gda__=1430022161_15c1d64066dcdb14b30a51b42b32931 6

https://scontent-b.xx.fbcdn.net/hphotos-xap1/v/t1.0-9/p180x540/10489825_919086371436105_2382726285082911183_n.jpg ?oh=be5a752683e26064db8cf0b4f1a06050&oe=552DDAC8

Updated picture of how to car sits at the moment, and me towing a ls400 that I have for sale.

[BiG MiKE86]

Where is your map sensor? Is that the IAT that I see with the brass colored base on the manifold?

[Javier13]

Yes the brass fitting is the sensor. Like i said I just got a tap and forced it in to re-thread it idr the NPT of a GM sensor.

Map sensor is furthest vacuum line to the right under the intake manifold with a alum. bracket I made.

[Y0SH]

Where do you get the braided selves you used on the engine harness, and how much does it run?

[Javier13]

bunch of places but I'll give you a site for one and it's wire-care.

[KAs14slider]

For the new map and IAT did they come with plugs for them that you had to wire into your harness or did you get a custom harness that already had the plugs for them on it?

[Javier13]

I first modified my harness didn't work since it was an automatic harness and i fucked something up. Sent out my harness to panic wire told him all the specs of the harness and he made it. The sensors when you buy them from AEM, and haltech should come with the diagram and plugs for it. But if you go to parts store it will not.

[Y0SH]

Panic wiring does great quality work for a good price!

[Javier13]

Panic wiring does great quality work for a good price!

Yea he use to live where I live. Awesome work happy I went through him than another company. But my next engine harness I'm doing it on my own.

[HypnoFish]

I see you shortened your TB. what did you do with the (coolant?) line that is on the bottom side of it. I assume this can just be bypassed and isnt needed.

[Javier13]

I see you shortened your TB. what did you do with the (coolant?) line that is on the bottom side of it. I assume this can just be bypassed and isnt needed.

Not needed. Like I said anything that can be taken off was taken off. Only the necessities were left lol. Make shit a lot easier to deal with.

[HypnoFish]

yeah, i agree with that. Ill be keeping my IACV though haha.

What did you do for rad pipes?

[Javier13]

yeah, i agree with that. Ill be keeping my IACV though haha.

What did you do for rad pipes?

Bought aluminum tube (what ever grade you want) and two silicone pipes one straight and one 90* and silicone lower hose from ebay that's a 4 ply.

[Javier13]

PBM has awesome customer service no BS. Thanks Tommy. My EVDM screen was not displaying correctly called Tommy and decided to manufacturing defect it.

eZK4YnurOP8
https://mail.google.com/mail/u/0/?ui=2&ik=8ba96dae2e&view=fimg&th=14af0a3c503b68de&attid=0.2&disp=inline&safe=1&attbid=ANGjdJ8l7zNZz-IVzQHcVaB8QjZLbo4TescoN_MyR2ehUQKKwV0oJJk5368eK1bm Jwm6X90OH70PPtXFVRn2yGsTPjdH2m90i-RPSJi8ObHHch2V9F2Aii6LZlPuskM&ats=1421376477997&rm=14af0a3c503b68de&zw&sz=w1345-h574

Persona Q game I've been playing
https://mail.google.com/mail/u/0/?ui=2&ik=8ba96dae2e&view=fimg&th=14af0a3c503b68de&attid=0.1&disp=inline&safe=1&attbid=ANGjdJ_5EBX18Uu_GG32XFX7XemF-YoeccZfOqHD0cLF9VG5JBb-q4osV3PbfLr33cVnNr6SD4t1VuRUBFRvkPFx60P8K0rFS7LNfU 8V78htq8TYvtQC8gHpsNuLqJE&ats=1421376477997&rm=14af0a3c503b68de&zw&sz=w1345-h574

Just two more semesters and I'm done can't wait.... Shit ton of books....:picardfp:
https://mail.google.com/mail/u/0/?ui=2&ik=8ba96dae2e&view=fimg&th=14af0a3c503b68de&attid=0.3&disp=inline&safe=1&attbid=ANGjdJ_0DaIB3GsghU7OCtbJbqfn1Qv1-sTIDUW1_zhkbsCnU_eAmfCy9nnHpVOwvPfV2_ezFhSN-vE07iB4FEqdYD7HjAjhKyeH2uwU_f-jlKYESATU6_1ZwVV8d74&ats=1421376477997&rm=14af0a3c503b68de&zw&sz=w1345-h574

And a FSAE video of them testing the 2014 car. Drove it and I did terrible, and the ergonomics were shit.
06fChbIQoqk

[Javier13]

BgYmS-bM-n4

Yes this video looks like it was taken with a potato but I did not film this. But this was my best run of the entire day.

[Javier13]

https://fbcdn-sphotos-f-a.akamaihd.net/hphotos-ak-xpf1/v/t1.0-9/10434008_937653399579402_2711056106349028390_n.jpg ?oh=74bb6bf941983c977ad5b7d312b6ac3d&oe=5557F2A7&__gda__=1428477901_17e0e7cc7375f8024bbb54e0dc17597 2

FSAE harness

[ahrens_240]

Are you still using the odyssey fab knuckles or did you switch to PBM?

[Javier13]

I'm still running odyssey fab knuckles and have been for 2+ years.

[Javier13]

For some reason whenever I go home I always manage to tow a car somewhere for someone lol.

[vJilly]

bring this thing back.. fix your pictures lol easily my favorite build.

[BiG MiKE86]

^ This for sure

[Dalton]

please fix your pictures

[Javier13]

I have a lot I would need to fix. Legit gave up keeping up with all my pictures since I don't remember which was which.

Update I blew up my 1jz
my f350 engine blew up as well
Car got a cage
Bought a new 2016 6.7 f250
Graduated College
Got a bad ass job
Car is getting a 6262 w/ a .58 rear housing
ID1000's and a lot of supporting mods

Will probably keep updating from here on but to go back and figure out what pics I used will be a pain!

[Javier13]

If someone can inform me on how to revive all my images easily I will fix it them all.

[Malik]

too bad, the pics are busted :/

[vJilly]

did you sell the HE351?


Sent from my iPhone using Tapatalk

[Javier13]

yeah im super bummed about it. I guess Ill do a small update on everything tonight

[Javier13]

yes HE351 is sold. Sold it to my friend locally

[Javier13]

Green Cover Speed Way

https://scontent-mia1-2.xx.fbcdn.net/v/t1.0-9/1383035_954346774685776_8657449781640925996_n.jpg? oh=c375087f09dbfd1d6911e46b4afaa117&oe=58899857

https://scontent-mia1-2.xx.fbcdn.net/v/t1.0-9/12565439_954347444685709_1144004523483626411_n.jpg ?oh=22b7c8dde24b54cac22de80111fbadbd&oe=58BCED2A

https://scontent-mia1-2.xx.fbcdn.net/v/t1.0-9/225232_954348488018938_9207337685406056455_n.jpg?o h=c8e60450c9cea7dd9865dd5912627e18&oe=58C52C1E


https://scontent-mia1-2.xx.fbcdn.net/v/t1.0-9/12814771_954350711352049_7854976004701458945_n.jpg ?oh=cb42f78e1d1a4bc4ecafb4735f5425da&oe=58CFDDA5

I bring everything to the track. Its nice to have a 8' bed space

https://scontent-mia1-2.xx.fbcdn.net/v/t1.0-9/12920333_1204682772876462_689495773512352699_n.jpg ?oh=cd3e32da5b86b60c94ffd3f1efd19f85&oe=588F4512

Some random car show early 2016
https://scontent-mia1-2.xx.fbcdn.net/v/t1.0-9/11223308_995230160488392_427165183991945128_n.jpg? oh=f3db8b8fdb256e061cd6bcaa8b97a1fa&oe=5890AB68

Sweet Exhaust my buddy at Odyssey Fab did for me!

https://scontent-mia1-2.xx.fbcdn.net/v/t1.0-9/10629618_1109479442396796_1001718099939437714_n.jp g?oh=80b7f2e7e9dc532c8357519cea20f48b&oe=58BEB9D4

Palm Beach International Raceway Prep 2015

https://scontent-mia1-2.xx.fbcdn.net/v/t1.0-9/11885349_1059668834044524_8940772553404270555_n.jp g?oh=375c726b220c5ae00ac46045c2942f67&oe=58CA314A

https://scontent-mia1-2.xx.fbcdn.net/v/t1.0-9/11891077_1061701927174548_7987192004314919411_n.jp g?oh=4ee64fdb6a23fcf6bb53ba67bd38f686&oe=58C3EB43

https://scontent-mia1-2.xx.fbcdn.net/v/t1.0-9/11889501_1061981440479930_9162123325632282346_n.jp g?oh=0064c1fd83244cc153fc02e7e5782595&oe=58D39C25

https://scontent-mia1-2.xx.fbcdn.net/v/t1.0-9/11892124_1061981443813263_510263782556505632_n.jpg ?oh=7be4cf33fb9ccd292ace748815686c4e&oe=58879EDC

https://scontent-mia1-2.xx.fbcdn.net/v/t1.0-9/11902326_1061981450479929_5333944499386683197_n.jp g?oh=5eb6e90857ce328af11cffb28a410ebf&oe=5889B866

[Javier13]

Jamming out to Born of Osiris in staging before my run

nQlJeyjY9oI

3rd Gear Clutch Kicks sound damn good w/ open external gate

SNHbQldUPIk