1993 240sx Sr20det Redtop - COMPLETE PART OUT

[zj2kwik]

Slave cylinder/Master cylinder went out today, I am no longer putting money into this project so its time to cut her up and say bu bye. Car runs and completely assembled as of today, 1-12-14.


Sr20det s13 redtop with sr trans, roughly 49,000 miles on set/Complete wiring harness
-Megan short throw
-Exedy stage 1 Clutch Kit
-Needs new head gasket
-Stock t25 turbo

1900 firm



Greddy VSPL Front mount/Greddy hot pipe/Greddy RS BO/Ebay manual boost controller
-Front mount 8/10 condition
-All piping and BO valve 10/10

800 firm



Blitz NUR SPEC R full exhaust/Megan flex downpipe
-8/10 condition


500 firm



SHELL - 5 speed from factory
-All manual option w/cruise control

Willing to take offers on just about anything


-Front end (fenders hood bumper lights)
400 firm

PM with offers on shell parts or text

8479973762



WILL SELL full swap (motor trans turbo front mount all piping and exhaust turbo back) for 2700 firm.






http://imagizer.imageshack.us/v2/800x600q90/32/bbw2.jpg (https://imageshack.com/i/0wbbw2j)
http://imagizer.imageshack.us/v2/800x600q90/21/08hs.jpg (https://imageshack.com/i/0l08hsj)
http://imagizer.imageshack.us/v2/800x600q90/59/p4ae.jpg (https://imageshack.com/i/1np4aej)
http://imagizer.imageshack.us/v2/800x600q90/542/xf1x.jpg (https://imageshack.com/i/f2xf1xj)
http://imagizer.imageshack.us/v2/800x600q90/203/z3cp.jpg (https://imageshack.com/i/5nz3cpj)
http://imagizer.imageshack.us/v2/800x600q90/545/mjx1.jpg (https://imageshack.com/i/f5mjx1j)
http://imagizer.imageshack.us/v2/800x600q90/594/xfpd.jpg (https://imageshack.com/i/gixfpdj)
http://imagizer.imageshack.us/v2/800x600q90/844/ibva.jpg (https://imageshack.com/i/ngibvaj)
http://imagizer.imageshack.us/v2/800x600q90/854/cul9.jpg (https://imageshack.com/i/nqcul9j)
http://imagizer.imageshack.us/v2/800x600q90/829/zxn8.jpg (https://imageshack.com/i/n1zxn8j)
http://imagizer.imageshack.us/v2/800x600q90/826/l4ye.jpg (https://imageshack.com/i/myl4yej)
http://imagizer.imageshack.us/v2/800x600q90/59/re9v.jpg (https://imageshack.com/i/1nre9vj)
http://imagizer.imageshack.us/v2/800x600q90/19/vqqd.jpg (https://imageshack.com/i/0jvqqdj)
http://imagizer.imageshack.us/v2/800x600q90/854/s8m4.jpg (https://imageshack.com/i/nqs8m4j)
http://imagizer.imageshack.us/v2/800x600q90/823/atlb.jpg (https://imageshack.com/i/mvatlbj)
http://imagizer.imageshack.us/v2/800x600q90/850/hbon.jpg (https://imageshack.com/i/nmhbonj)
http://imagizer.imageshack.us/v2/800x600q90/11/tdbp.jpg (https://imageshack.com/i/0btdbpj)
http://imagizer.imageshack.us/v2/800x600q90/12/uyo2.jpg (https://imageshack.com/i/0cuyo2j)
http://imagizer.imageshack.us/v2/800x600q90/854/gy5c.jpg (https://imageshack.com/i/nqgy5cj)
http://imagizer.imageshack.us/v2/800x600q90/689/upmt.jpg (https://imageshack.com/i/j5upmtj)
http://imagizer.imageshack.us/v2/800x600q90/593/dnpy.jpg (https://imageshack.com/i/ghdnpyj)
http://imagizer.imageshack.us/v2/800x600q90/843/92xr.jpg (https://imageshack.com/i/nf92xrj)
http://imagizer.imageshack.us/v2/800x600q90/4/v6oy.jpg (https://imageshack.com/i/04v6oyj)
http://imagizer.imageshack.us/v2/800x600q90/542/3c6c.jpg (https://imageshack.com/i/f23c6cj)
http://imagizer.imageshack.us/v2/800x600q90/824/6lab.jpg (https://imageshack.com/i/mw6labj)
http://imagizer.imageshack.us/v2/800x600q90/17/gbjs.jpg (https://imageshack.com/i/0hgbjsj)
http://imagizer.imageshack.us/v2/800x600q90/203/p7df.jpg (https://imageshack.com/i/5np7dfj)

[zj2kwik]

Also RACELAND S13 coilovers, they were just installed and have less than 30 miles on them. Come with a 2 year warranty.

450 FIRM

[dorkidori_s13]

what seat is that?

[zj2kwik]

Sentra se-r

[dorkidori_s13]

how much modding did that take to fit?

[zj2kwik]

actually it wasn't that bad. I didn't drill into the floor board, it has independent left and right slide adjustments. This allowed me to rig it where it needed to be, along with minor bending. The front left could use some spacers, it currently tilts to that corner. Also it's a higher seating fitment, so If you're like 6'4 there's slim to no chance of you riding too comfy.

[kilamax03]

willing to part jsus the intercooler and piping

[kilamax03]

you have PM sir

[zj2kwik]

Ive got no new message? Id rather sell as what I have listed, but make it worth it and no problem

[kilamax03]

pm me lets work something out