z32 trans,PBM arms, Modded knuckles, Bride, Corbeau, Fuel Cell

[Kodykinns]

Sold sold sold sold aold

[240ss]

Knuckles for s13? And do they come with the extended lower control arm?

Sent from my XT907 using Tapatalk

[Kodykinns]

Knuckles for s13? And do they come with the extended lower control arm?

Sent from my XT907 using Tapatalk


Yes for s13 no lower control arms. Just the knuckles.

[s14sliding]

are you willing to sell the lower control arms? if so do they fit S14?

[Tankzor01]

interested in the knuckles, anything needed to get full potential out of them?

[team13]

R ruca s13 look s14 will u ship ?

Sent from my LG-US730 using Tapatalk

[blowitup]

Hey man interested in the knuckles. Ruca . And tension rods. Hit me up if you can or are willing to ship. 22602 is my zip

[Kodykinns]

are you willing to sell the lower control arms? if so do they fit S14?lower control arms are being used on a friends pro am car



interested in the knuckles, anything needed to get full potential out of them?

Extended lower control arms and longer inner and outter tie rods depending on how far you extend the lca. And low offset wheels to not hit the tension rod at full lock

R ruca s13 look s14 will u ship ?

Sent from my LG-US730 using Tapatalk


They're s13 I will ship flat rate for them anywhere in the states

Hey man interested in the knuckles. Ruca . And tension rods. Hit me up if you can or are willing to ship. 22602 is my zip

Replied to your pm. Not really interested in shipping the knuckles cause they won't fit flat rate so it's too much of a hassel.

[powahh]

Hey I want those tension rods. PM me.

[Slims]

whats the dimensions on that tank? does it have a sending unit? thanks.

[brian310]

damn it youre so far i want those rucas lol

[Kodykinns]

whats the dimensions on that tank? does it have a sending unit? thanks.

Not sure. I can measure it though. And no sending unit. Pretty sure it's meant to be used with an inline fuel pump setup.

damn it youre so far i want those rucas lol


Make a drive!

[Slims]

That would be cool. Thanks.

[Buummp]

Interested in the bride seat and rails.. 130$ and ill pick them up?

[Kodykinns]

Interested in the bride seat and rails.. 130$ and ill pick them up?


No thank you

[bathsaltsamurai]

Do you have 2 sets of the modded knuckles? Has anyone bought them yet? Do you offer shipping?

[Kodykinns]

Do you have 2 sets of the modded knuckles? Has anyone bought them yet? Do you offer shipping?


Only one set. The white set is on a buddy's pro am car. Almost every driver with an s chassis running topdrift pro am is running these knuckles. Don't really want to ship them.

[bathsaltsamurai]

Well I want them bro how's 175 shipped sound?


Sent from my iPod touch using Tapatalk (http://tapatalk.com/m?id=1)

[Kodykinns]

Well I want them bro how's 175 shipped sound?


Sent from my iPod touch using Tapatalk (http://tapatalk.com/m?id=1)


They won't fit flat rate. Know any cheap options? Last time I shipped something it cost me more than I sold the part for. Lol

[bathsaltsamurai]

Yeah I read where you mentioned that earlier after I posted that. Damn then idk man idk of any cheap options for shipping I guess glws they will at that price and bump for you


Sent from my iPod touch using Tapatalk (http://tapatalk.com/m?id=1)

[b.series]

hey what is the condition of the transmission? and are you willing to ship? i will pay whatever shipping cost is.

[Kodykinns]

hey what is the condition of the transmission? and are you willing to ship? i will pay whatever shipping cost is.


It was pulled out of a running driving z32. The dude was doing a 2j swap in it I bought it for a vh45 swap decided to scrap the idea and start a family. I'm going to guess freight would be about 200 bucks I'd honestly have to figure out how to do that. It's an na bell housing but has been grinded to clear a tt clutch/flywheel also.

[Slims]

Can I get those measurements? Bump

[g14novak]

They won't fit lat rate. Know any cheap options? Last time I shipped something it cost me more than I sold the part for. Lol

UPS or USPS Post are the 2 best options. Ive shipped things in flat rate boxes that didnt fit in the box at all. As long as the edges are sealed, they dont care if the box is bulging to the point that its about to explode


Second option would be ups. Find a standard box that someone is tossing out. You dont get charged extra unless the box is bigger than 24x12x12 or so. Should be ~13 lbs for both the knuckles. even with insurance, should only cost ~20$ to go ground from CA to OH. Even less if being delivered to a business.

Glws.

[bathsaltsamurai]

Yo I like what g14novak said, hey op you wanna try that with the knuckles?


Sent from my iPod touch using Tapatalk (http://tapatalk.com/m?id=1)

[Kodykinns]

Yo I like what g14novak said, hey op you wanna try that with the knuckles?


Sent from my iPod touch using Tapatalk (http://tapatalk.com/m?id=1)


Going to try and find a box and get a quote today where is it shipping too?

[bathsaltsamurai]

43081 if you need my full address I'll pm it to you, thanks for looking into shipping for me!


Sent from my iPod touch using Tapatalk (http://tapatalk.com/m?id=1)

[Kodykinns]

43081 if you need my full address I'll pm it to you, thanks for looking into shipping for me!


Sent from my iPod touch using Tapatalk (http://tapatalk.com/m?id=1)
Ill get you a shipping quote and PM it too you ASAP

[beeboyee]

still got them tension rods?

[Kodykinns]

still got them tension rods?


Yes I do. MSGlgth

[d_nice]

good parts here

[Kodykinns]

Bump to the top. Get this shit gone

[Kodykinns]

Last time before it just gets left on the shell.

[bathsaltsamurai]

So any progress made on getting me the shipping quote on them modded knuckles?

[Kodykinns]

So any progress made on getting me the shipping quote on them modded knuckles?


No. I just don't have the time to deal with it. That's why I'd just rather not ship them. Sorry

[90S13]

Possible to ship the RUCAs? If so to 89147 please.

[Rotary04]

If you are willing to ship the tension rods and rucas I'm interested

[Kodykinns]

Mods please close this. People can't realize this post is many months old

[nissangooroo]

still have the rucas?

[nissangooroo]

i know its march but do u still have the PBM GEN 1 RUCAS????

[nissangooroo]

sorry just noticed i replied 3 times i cant delete messages my bad