suspectu1
11-13-2013, 12:23 PM
Hey guys, I decided to give back to the internet community by sharing some of my knowledge in a set of short tutorials. Hope you will enjoy. The first installment is how to fix your RPF1s and a bonus!!!
Ok so here's the 2 wheels needing attention. Curb rash all around on one and 2/3 on the other.
http://farm6.staticflickr.com/5508/10841260865_624a596afd_z.jpg
http://farm3.staticflickr.com/2875/10841260295_46d7f8401f_z.jpg
What you need to do is first off, get the tires off!
Then you will get a metal file and start filing away the scratches on the lip of each wheel. Make sure to only take away as much metal as needed to smooth out the lip without taking too much.
For the inside of the lip you will use small pieces of sand paper 220 grit and smooth away any damaged metal. Photo of the aftermath.
http://farm8.staticflickr.com/7428/10841588693_8d46494f94_z.jpg
Next you need to apply 3m paint tape all around the inside of the lip and the outside. This will avoid you putting JB Weld where there shouldn't be any.
Next up, you mix your JB Weld (i used the original one, black and red bottles) and apply it all around the lip in a good even coat. You can apply it with a piece of aluminum and make sure it's as smooth as possible to avoid having to sand too much.
http://farm6.staticflickr.com/5501/10841256105_a384a467dc_z.jpg
As soon as you're done, remove the tape SLOWLY! Don't wanna have to sand it out of there.
Next you let it cure for 24 hours to be safe!
After it's completely dry, you can start sanding it with a block (wood, or Norton rubber block) and 220 grit paper. YOU NEED THE BLOCK! otherwise it'll come out wavy!
Next up you take smaller pieces of 220 and using your hands alone, go sand the inside of the lip slowly, making sure to get a smooth finish. Do the same for the outside. Take your time!
http://farm8.staticflickr.com/7295/10841586623_26d989faae_z.jpg
Next up is the clean up! Use either rubbing alcohol or some wax and grease remover.
Make a small scraper to remove the Enkei logos. I made mine from one of those hard plastic product boxes. Just cut it out, and pass one end over a piece of sand paper to make it very thin.
http://farm4.staticflickr.com/3756/10841584913_bf77c8fced_z.jpg
After you remove the logos, you are ready to roughen up the clear coat on the rest of the wheel, at least where you're gonna paint. Use 800 grit sand paper or one of those light grey scotch pads.
Degrease again!
Next up is the bonus section you all wanted to find out about! The mysterious color used on the Enkei RPF1. Well i'd like to share that i found Honda's Quartz Silver NH94M to be a VERY VERY VERY close match to the original. I can't tell the difference honestly.
Paint them with this color, maybe 3-4 coats to be sure.
Throw some clear coat over to bring back the shine and you're done! You can use as many coats of clear as you want.
http://farm8.staticflickr.com/7393/10841312586_8c0d802aa3_z.jpg
http://farm3.staticflickr.com/2835/10841585703_472dca50b8_z.jpg
AND YOU'RE DONE! Now you can get some new Enkei logos from ebay or just leave as is, so the haters think they're fake and don't bother stealing your wheels :faint:
*note the last photo is only 1 coat of clear. You should use a spray gun and urethane clear coat if you want better results. It was already too cold up here in Canada for me to spray urethane so i just used aerosol. Will put down a proper clear in spring.
Ciao ;)
Ok so here's the 2 wheels needing attention. Curb rash all around on one and 2/3 on the other.
http://farm6.staticflickr.com/5508/10841260865_624a596afd_z.jpg
http://farm3.staticflickr.com/2875/10841260295_46d7f8401f_z.jpg
What you need to do is first off, get the tires off!
Then you will get a metal file and start filing away the scratches on the lip of each wheel. Make sure to only take away as much metal as needed to smooth out the lip without taking too much.
For the inside of the lip you will use small pieces of sand paper 220 grit and smooth away any damaged metal. Photo of the aftermath.
http://farm8.staticflickr.com/7428/10841588693_8d46494f94_z.jpg
Next you need to apply 3m paint tape all around the inside of the lip and the outside. This will avoid you putting JB Weld where there shouldn't be any.
Next up, you mix your JB Weld (i used the original one, black and red bottles) and apply it all around the lip in a good even coat. You can apply it with a piece of aluminum and make sure it's as smooth as possible to avoid having to sand too much.
http://farm6.staticflickr.com/5501/10841256105_a384a467dc_z.jpg
As soon as you're done, remove the tape SLOWLY! Don't wanna have to sand it out of there.
Next you let it cure for 24 hours to be safe!
After it's completely dry, you can start sanding it with a block (wood, or Norton rubber block) and 220 grit paper. YOU NEED THE BLOCK! otherwise it'll come out wavy!
Next up you take smaller pieces of 220 and using your hands alone, go sand the inside of the lip slowly, making sure to get a smooth finish. Do the same for the outside. Take your time!
http://farm8.staticflickr.com/7295/10841586623_26d989faae_z.jpg
Next up is the clean up! Use either rubbing alcohol or some wax and grease remover.
Make a small scraper to remove the Enkei logos. I made mine from one of those hard plastic product boxes. Just cut it out, and pass one end over a piece of sand paper to make it very thin.
http://farm4.staticflickr.com/3756/10841584913_bf77c8fced_z.jpg
After you remove the logos, you are ready to roughen up the clear coat on the rest of the wheel, at least where you're gonna paint. Use 800 grit sand paper or one of those light grey scotch pads.
Degrease again!
Next up is the bonus section you all wanted to find out about! The mysterious color used on the Enkei RPF1. Well i'd like to share that i found Honda's Quartz Silver NH94M to be a VERY VERY VERY close match to the original. I can't tell the difference honestly.
Paint them with this color, maybe 3-4 coats to be sure.
Throw some clear coat over to bring back the shine and you're done! You can use as many coats of clear as you want.
http://farm8.staticflickr.com/7393/10841312586_8c0d802aa3_z.jpg
http://farm3.staticflickr.com/2835/10841585703_472dca50b8_z.jpg
AND YOU'RE DONE! Now you can get some new Enkei logos from ebay or just leave as is, so the haters think they're fake and don't bother stealing your wheels :faint:
*note the last photo is only 1 coat of clear. You should use a spray gun and urethane clear coat if you want better results. It was already too cold up here in Canada for me to spray urethane so i just used aerosol. Will put down a proper clear in spring.
Ciao ;)