wisDOMination
10-29-2013, 12:44 AM
S13 PBM Adjustable Rear lower control arm- BRAND NEW $550
http://s15.postimg.org/lhszwq8yj/image.jpg
S13 PBM Super Angle Knuckles w/ roll center/bumpsteer correction- BRAND NEW ***SOLD***
http://s15.postimg.org/8rk65wbmj/image.jpg
S13 Ichiba rear 5lug conversion hubs- BRAND NEW $250
http://s15.postimg.org/jaor8t3ob/image.jpg
S13 Nismo steering rack bushings. Both L&R- BRAND NEW $100
http://s12.postimg.org/7t7cgboe5/image.jpg
S13 Silvia OEM headlight brackets. Only used for mockup- BRAND NEW ***SOLD***
http://s12.postimg.org/wazg47qyl/image.jpg
S13 Silvia DMAX clear corners-BRAND NEW ***SOLD***
http://s12.postimg.org/vu9n41dtp/image.jpg
S13 Silvia/s13 pig nose DMAX clear turn signals- BRAND NEW $70
http://s15.postimg.org/n389ojj6j/image.jpg
S13/S14 Stoptech BBK- USED $2500
Front/rear rotors, calipers, pads, steel braided brake lines, and will also come with Z32 parking brake components/cables. May have to change 1 rotor due to some rust, the rest can be run. I was planning on replacing all if them.
http://s15.postimg.org/3nxhvfpwb/image.jpg
http://s15.postimg.org/b6gn42h97/image.jpg
http://s15.postimg.org/m280zf26z/image.jpg
http://s15.postimg.org/rb31xakm3/image.jpg
http://s15.postimg.org/68yh57pwb/image.jpg
And last but not least...
Neo VVL RWD long block with custom ITB set up
>head
SR16VE head
SR20VE cams
Tomei adjustable cam gears
Ported/Blended at Portflow
Supertech valves/springs/retainers
New valve guides/seals
20v cam angle sensor
-an fittings welded on valve cover
Modified water neck for RWD configuration
>block
S14 SR20DET block
86.5mm 9.1:1 compression Ross Pistons
Mazworx 1/2" head studs
Mazworx calico coated bearings
Greddy oil pan
Oil filter block with -an fittings
Rear oil drain plugged/oil pickup tube/crank pulley modified for VVL conversion
Block is fully balanced
>Intake
Custom Hayabusa ITB's with plenum for ITB Turbo set up
-an fittings for vacuum source
BDL top feed fuel rail
Vacuum block
Engine was built by a pretty well known drifter/drift car builder Bryan Rogers. Built in house at JIC/Ziel Motorsports.
$6500 OBO for the whole set up
Bryan Rogers wants to buy back the head to put on his stroker 2.2L SR block, so willing to sell the block separate for those who already have a VVL head, and are looking for a built/balanced block ready to just bolt onto. I offered to sell him the head ONLY if someone scoops the block.
http://s15.postimg.org/u2hqa5tqz/image.jpg
http://s15.postimg.org/ndb6u58ez/image.jpg
All prices are NOT firm. Willing to take reasonable offers. Also willing to take trades.
Will ship at buyers expense.
Thanks
http://s15.postimg.org/lhszwq8yj/image.jpg
S13 PBM Super Angle Knuckles w/ roll center/bumpsteer correction- BRAND NEW ***SOLD***
http://s15.postimg.org/8rk65wbmj/image.jpg
S13 Ichiba rear 5lug conversion hubs- BRAND NEW $250
http://s15.postimg.org/jaor8t3ob/image.jpg
S13 Nismo steering rack bushings. Both L&R- BRAND NEW $100
http://s12.postimg.org/7t7cgboe5/image.jpg
S13 Silvia OEM headlight brackets. Only used for mockup- BRAND NEW ***SOLD***
http://s12.postimg.org/wazg47qyl/image.jpg
S13 Silvia DMAX clear corners-BRAND NEW ***SOLD***
http://s12.postimg.org/vu9n41dtp/image.jpg
S13 Silvia/s13 pig nose DMAX clear turn signals- BRAND NEW $70
http://s15.postimg.org/n389ojj6j/image.jpg
S13/S14 Stoptech BBK- USED $2500
Front/rear rotors, calipers, pads, steel braided brake lines, and will also come with Z32 parking brake components/cables. May have to change 1 rotor due to some rust, the rest can be run. I was planning on replacing all if them.
http://s15.postimg.org/3nxhvfpwb/image.jpg
http://s15.postimg.org/b6gn42h97/image.jpg
http://s15.postimg.org/m280zf26z/image.jpg
http://s15.postimg.org/rb31xakm3/image.jpg
http://s15.postimg.org/68yh57pwb/image.jpg
And last but not least...
Neo VVL RWD long block with custom ITB set up
>head
SR16VE head
SR20VE cams
Tomei adjustable cam gears
Ported/Blended at Portflow
Supertech valves/springs/retainers
New valve guides/seals
20v cam angle sensor
-an fittings welded on valve cover
Modified water neck for RWD configuration
>block
S14 SR20DET block
86.5mm 9.1:1 compression Ross Pistons
Mazworx 1/2" head studs
Mazworx calico coated bearings
Greddy oil pan
Oil filter block with -an fittings
Rear oil drain plugged/oil pickup tube/crank pulley modified for VVL conversion
Block is fully balanced
>Intake
Custom Hayabusa ITB's with plenum for ITB Turbo set up
-an fittings for vacuum source
BDL top feed fuel rail
Vacuum block
Engine was built by a pretty well known drifter/drift car builder Bryan Rogers. Built in house at JIC/Ziel Motorsports.
$6500 OBO for the whole set up
Bryan Rogers wants to buy back the head to put on his stroker 2.2L SR block, so willing to sell the block separate for those who already have a VVL head, and are looking for a built/balanced block ready to just bolt onto. I offered to sell him the head ONLY if someone scoops the block.
http://s15.postimg.org/u2hqa5tqz/image.jpg
http://s15.postimg.org/ndb6u58ez/image.jpg
All prices are NOT firm. Willing to take reasonable offers. Also willing to take trades.
Will ship at buyers expense.
Thanks