Slidingmonkey
09-08-2013, 03:50 PM
For sale as a whole car that needs to be completed...but can run and drive on the road as is.
OR
PART OUT: -Complete Motor/Tranny setup w/ driveshaft
-Complete unmolested shell
MOTIVATED SELLER
Will only trade for solid daily driving car, complete SR20 swapped S13, 06+ motorcycle, or something i can easily sell back to pull my money back out of.
Asking Price: $4200 OBO
WILL ONLY PART COMPLETE SHELL OR MOTOR/TRANNY SETUP
Up for sale is a 1992 240SX with a fresh built RB25 Series 1 swap. Boosted with a CXRacing GT30 turbo. It is being sold as a complete rolling shell and a complete RB25 motor. The reason being is I have not finished all the cosmetic things on it. I do not have the finances to own this car at the moment, I am trying to launch my business and therefore will sell this thing for any reasonable offer.
CLEAN TITLE (NEVER DRIFTED YET) S13 SHELL-NO RUST
Series 1 RB25 W/ GT30
RB25 Trans w/ Spec 3 Stage clutch
Less 3K miles since motor build
Only 175k on the body
Does have power steering (needs hoses attached and clamped up)
No A/C (does have lines still but no compressor)
Manual Crank Windows
Information/History on the shell:
The CLEAN TITLED shell was bought in Miami with a blown stock KA motor and a automatic transmission. The car was 100% stock when I bought it. It was towed to the shop and prepped for the swap. The interior is in decent shape besides the dashboard. Seats are in great condition along with the clean carpets on the inside. The dashboard was given a quick bondo job and a quick black spray paint job because the dash was cracked. The steering wheel also needs to be replaced as it is a cheap steering wheel that has snapped. The drivers side window is in place but does not go down. There is also a slight dent on the drivers side quarter panel (you can see in the picture). The only thing modified on the shell was the BRAND NEW SUSPENSION PARTS I just installed on it.
BRAND NEW SUSPENSION PARTS JUST INSTALLED (A full 10 pc kit):
Front Sway Bar
Rear Sway Bar
Camber Arms
Traction
Tension Rods
Toe Arm
Information on the engine:
Brand New Aeromotive 11141 Fuel pump
Tuned stock ECU
ACL Main and Rod Bearing
ARP Main and Rd Bolts
ARP Headstuds
Weisco 8:4:1 forged pistons
Stock Rods
Freddy Intake Manifold
90MM Billet Throttle Body
800CC Injectors
2 Flexlite electric fans
NEW Front mount Intercooler with custom aluminum piping (GREAT FABRICATION JOB AND CLEAN WELDS)
Z32 MAF Blow through
GT30R Top Mount CXRacing Turbo
Tial 38mm Wastegate
HKS Sequential BOV
Full 3" V-Band Exhaust
AEM air Filter
Mckinney Mount Kit
SAFC NEO
May have left a couple things out. Many of the engine parts are BRAND NEW if not new then recently rebuilt! Some things haven't even been used since it's been mounted to the car!
To complete the car to make it fully running street car:
-Buy & Install wideband
-Finish exhaust from the downpipe back (able to run as is but will be loud)
-Bleed/add fluid to brakes and clutch
-Buy & Install radiator cap for the stock KA radiator OR purchase and custom mount the BRAND NEW 2 Row aluminum radiator I have for it ($100 from me or $150 elsewhere)
-Buy & Install: Replace steering wheel as the old one is snapped
MOTIVATED SELLER
Asking Price: $4200 OBO
OR
PART OUT: -Complete Motor/Tranny setup w/ driveshaft
-Complete unmolested shell
MOTIVATED SELLER
Will only trade for solid daily driving car, complete SR20 swapped S13, 06+ motorcycle, or something i can easily sell back to pull my money back out of.
Asking Price: $4200 OBO
WILL ONLY PART COMPLETE SHELL OR MOTOR/TRANNY SETUP
Up for sale is a 1992 240SX with a fresh built RB25 Series 1 swap. Boosted with a CXRacing GT30 turbo. It is being sold as a complete rolling shell and a complete RB25 motor. The reason being is I have not finished all the cosmetic things on it. I do not have the finances to own this car at the moment, I am trying to launch my business and therefore will sell this thing for any reasonable offer.
CLEAN TITLE (NEVER DRIFTED YET) S13 SHELL-NO RUST
Series 1 RB25 W/ GT30
RB25 Trans w/ Spec 3 Stage clutch
Less 3K miles since motor build
Only 175k on the body
Does have power steering (needs hoses attached and clamped up)
No A/C (does have lines still but no compressor)
Manual Crank Windows
Information/History on the shell:
The CLEAN TITLED shell was bought in Miami with a blown stock KA motor and a automatic transmission. The car was 100% stock when I bought it. It was towed to the shop and prepped for the swap. The interior is in decent shape besides the dashboard. Seats are in great condition along with the clean carpets on the inside. The dashboard was given a quick bondo job and a quick black spray paint job because the dash was cracked. The steering wheel also needs to be replaced as it is a cheap steering wheel that has snapped. The drivers side window is in place but does not go down. There is also a slight dent on the drivers side quarter panel (you can see in the picture). The only thing modified on the shell was the BRAND NEW SUSPENSION PARTS I just installed on it.
BRAND NEW SUSPENSION PARTS JUST INSTALLED (A full 10 pc kit):
Front Sway Bar
Rear Sway Bar
Camber Arms
Traction
Tension Rods
Toe Arm
Information on the engine:
Brand New Aeromotive 11141 Fuel pump
Tuned stock ECU
ACL Main and Rod Bearing
ARP Main and Rd Bolts
ARP Headstuds
Weisco 8:4:1 forged pistons
Stock Rods
Freddy Intake Manifold
90MM Billet Throttle Body
800CC Injectors
2 Flexlite electric fans
NEW Front mount Intercooler with custom aluminum piping (GREAT FABRICATION JOB AND CLEAN WELDS)
Z32 MAF Blow through
GT30R Top Mount CXRacing Turbo
Tial 38mm Wastegate
HKS Sequential BOV
Full 3" V-Band Exhaust
AEM air Filter
Mckinney Mount Kit
SAFC NEO
May have left a couple things out. Many of the engine parts are BRAND NEW if not new then recently rebuilt! Some things haven't even been used since it's been mounted to the car!
To complete the car to make it fully running street car:
-Buy & Install wideband
-Finish exhaust from the downpipe back (able to run as is but will be loud)
-Bleed/add fluid to brakes and clutch
-Buy & Install radiator cap for the stock KA radiator OR purchase and custom mount the BRAND NEW 2 Row aluminum radiator I have for it ($100 from me or $150 elsewhere)
-Buy & Install: Replace steering wheel as the old one is snapped
MOTIVATED SELLER
Asking Price: $4200 OBO