PDA

View Full Version : GA 76' 280z roller


skimattybee
06-20-2013, 09:06 PM
I bought this car mainly for suspension parts that were on it, and I planned to turn this car into a auto-x rat...but I have no room and I still need to finish my turbo 260 build. I swapped the stock suspension back into the car and now I need to sell.

Details:
- It does not come with the vented hood. It comes with a stock s30 hood.
-the drivers side fender is dented in 2 places. I have a replacement fender and headlight bucket that will be included.
-I also have a spare pass. Fender and cowl that are included.
-r200 rear end is out of the car but will be included.
-the hatch is rusted out. I also have a clean replacement with a good seal/glass/trim that will be included.
- the only rust spots are a 4"x4" spot under the battery tray. And 2 dime sized spots on the bottom of drivers side dogleg.
-no rust on floor pans/frame rails/spare tire..ect...
-newish polyurethane control arm bushings. (Outer rears not installed) missing right front bushing sleeve. I also have a set of new OEM rear bushings not installed.
-PO had a ford 5.0 in the car. And broke a drive shaft, therefore a dent in trans tunnel( nothing to worry about)
-wilwood hydraulic clutch reservoir
-bolt on camber plates up front.
-good wheels and tires. American eagle 15x7 +25 with no damage . 215/60/15 Bridgestone potenza all around with good rubber
-lowered on cut springs
-needs dash pad and center console to complete interior
- I bought the car with a bill of sale only, so thys how it will be sold..state of GA no title is needed for antique cars over 25 years old.

http://i30.photobucket.com/albums/c306/skimattybee/photo_zps2df00644.jpg (http://s30.photobucket.com/user/skimattybee/media/photo_zps2df00644.jpg.html)

http://i30.photobucket.com/albums/c306/skimattybee/photo_zps095253ab.jpg (http://s30.photobucket.com/user/skimattybee/media/photo_zps095253ab.jpg.html)

http://i30.photobucket.com/albums/c306/skimattybee/photo_zps3da6b4a8.jpg (http://s30.photobucket.com/user/skimattybee/media/photo_zps3da6b4a8.jpg.html)

http://i30.photobucket.com/albums/c306/skimattybee/photo_zps196f9e52.jpg (http://s30.photobucket.com/user/skimattybee/media/photo_zps196f9e52.jpg.html)

http://i30.photobucket.com/albums/c306/skimattybee/photo_zps6cdeedbb.jpg (http://s30.photobucket.com/user/skimattybee/media/photo_zps6cdeedbb.jpg.html)
http://i30.photobucket.com/albums/c306/skimattybee/photo_zps4b8e4f64.jpg (http://s30.photobucket.com/user/skimattybee/media/photo_zps4b8e4f64.jpg.html)

http://i30.photobucket.com/albums/c306/skimattybee/photo_zps67ad9627.jpg (http://s30.photobucket.com/user/skimattybee/media/photo_zps67ad9627.jpg.html)

http://i30.photobucket.com/albums/c306/skimattybee/photo_zps12455eb9.jpg (http://s30.photobucket.com/user/skimattybee/media/photo_zps12455eb9.jpg.html)

http://i30.photobucket.com/albums/c306/skimattybee/photo_zps08b782c5.jpg (http://s30.photobucket.com/user/skimattybee/media/photo_zps08b782c5.jpg.html)
http://i30.photobucket.com/albums/c306/skimattybee/photo_zpsb3c2e312.jpg (http://s30.photobucket.com/user/skimattybee/media/photo_zpsb3c2e312.jpg.html)

http://i30.photobucket.com/albums/c306/skimattybee/photo_zps2316fd2e.jpg (http://s30.photobucket.com/user/skimattybee/media/photo_zps2316fd2e.jpg.html)

$1500 firm! CHEAP CLEAN ROLLER!!
912-224-4731

Interested in trades for:
low offset wide wheels 4x114.3 no bigger than 17"
Carbon fiber s30 parts
Zg flares
Z32 trans swap kit for s30
Long nose r200 vlsd diff and axles
L28 turbo stuff
Megasquirt ECU
Haltech ECU
Anything cool!

Homeboyx
06-21-2013, 01:02 AM
Bolt on camber plates? Any close up pictures on that? I'm curious..

skimattybee
06-21-2013, 06:45 PM
Yeah I'll snap a couple photos of that tomorrow. It's not the way I would have chosen to go. Installed by PO

Homeboyx
06-21-2013, 11:00 PM
Cool thanks.

Sito
06-22-2013, 12:43 AM
Free bump for you; a good priced shell. Rust doesn't look too bad and it comes with some goodies.
Whats the turbo 260 build? Are you on hyrbidz?

skimattybee
06-22-2013, 02:59 PM
Thank you good sir^...yeah I really want to keep it because its so clean, but i need space and cash...I'm building an l28et, about 60% finished with the build. Just got my TTT coilovers,TC rods , front and rear control arms and ron tyler diff mount installed , still have to put on the brakes. Z32's up front and JSK 4 pot rears. And TTT mustache bar. The engine is lagging right now. Gotta get this shell Gone so I can finish it up! Still need arp's throughout , forged pistons, head gasket and EMS and a few other items

skimattybee
06-24-2013, 01:09 PM
Bump it up!

skimattybee
06-29-2013, 10:44 PM
Bump it up! Interested in trades too, Honda ruckus or similar , s30 parts, guns, triple webber/mikuni carbs..wheels. Anything cool!

rb27dets14
06-29-2013, 10:56 PM
My car needs to sell this is the perfect street beater....Rb25 as it sits and drive it around

skimattybee
07-01-2013, 08:14 AM
Sounds good! Do it ^^

skimattybee
07-05-2013, 03:53 PM
Bump it up! Someone snag this!

Homeboyx
07-06-2013, 01:37 AM
No picture of bolt on camber plates? :(

skimattybee
07-06-2013, 09:15 AM
http://i30.photobucket.com/albums/c306/skimattybee/photo_zpsef8450a5.jpg (http://s30.photobucket.com/user/skimattybee/media/photo_zpsef8450a5.jpg.html)

[URL=http://s30.photobucket.com/user/skimattybee/media/photo_zps543b5f61.jpg.html]http://i30.photobucket.com/albums/c306/skimattybee/photo_zps543b5f61.jpg[/URL

Here ya go! The PO trusted them with a ford 302 on the drag strip

youradumb1
07-06-2013, 11:40 AM
wow that is just awesome

Homeboyx
07-06-2013, 01:47 PM
Only one nut and bolt hold them on?! WTF?

skimattybee
07-06-2013, 03:52 PM
I believe There is a plate on the bottom. Haha like I said *i did not install these and I wouldn't trust them* I'd highly recommend welding some Plates on instead of using these.

silents1ick
07-07-2013, 12:42 PM
pretty clean car and fair price.... seen this car in person.. wish had hte money to buy it... bump for good seller...bought few items from him b4

skimattybee
07-09-2013, 08:19 PM
Thank you sir^

skimattybee
07-13-2013, 09:59 PM
Bump! Price is OBO. And trades

skimattybee
07-22-2013, 11:02 AM
Still for sale

skimattybee
07-30-2013, 08:49 PM
Bump! A good amount if interest but everyone has backed out

skimattybee
09-03-2013, 07:44 PM
Price reduced to $1200 ! I need this gone