Turnkey 350HP S14 SR20 Swap

[BoostinIX]

Going LS, testing waters on selling the turnkey. Everything you'll need to install and drivehttp://images.intellitxt.com/ast/adTypes/icon1.png (http://zilvia.net/f/#) is here.

S14SR -
.20 over.
Scat Rods, CP Pistons, acl bearings, polished crank. Apexi MHG. Head had seals and guides replaced. Water + oil pump were replaced along with timing kit. Essentially everything was new or refreshed at time of build, has under 10k miles on it.
Tomei M7960 turbohttp://images.intellitxt.com/ast/adTypes/icon1.png (http://zilvia.net/f/), Expreme mani/elbow, RAS, oil pan, 740cc Injectors, CP cover, oil cap, N2 oil filter adapter
RS*R downpipe
Wiring Specialties premade harness S14SR -> S14
Nismo motor/trans mount
Z32 Maf/Apexi intake
Blitz SBC-ID Spec R / Powerhttp://images.intellitxt.com/ast/adTypes/icon1.png (http://zilvia.net/f/#) meter
Blitz FMIC w/ sunk in piping to sit between frame sections
Blitz Hotpipe/VD BOV
GKTech Throttle pulley
B&M Short shifter / Competitionhttp://images.intellitxt.com/ast/adTypes/icon1.png (http://zilvia.net/f/) Clutch and Flywheel / Nismo Slave + Pivot / DSS aluminum driveshaft
Stance water pulley / DIF water neck adapter
CodyAce AC Brackethttp://images.intellitxt.com/ast/adTypes/icon1.png (http://zilvia.net/f/#)
Enjuku Exh. Manifold studs / 7layer gasket.
Ceramic coating on manifold/elbow
ARP Flywheel and head bolts
CS remote oil filter setup
Nistune ECU
Mishimoto X-Line 3 core radiator / Mishimoto fans & shroud / Samco hoses


350hp/343 tq


GRx9JFhqN3I


http://distilleryimage0.s3.amazonaws.com/e26b5462851e11e294d322000a1f8c09_7.jpg


Not parting, reeeeeally not looking to ship.

$6k, partial trade for t56. If motor is bought/paid for, will part the rest.

[energy0uth]

Dis dat so so def shit. Real legities.

Just a bump/vouch for a legit motor that was done right and sounds mean on the street.

Love,

Joe

[BoostinIX]

Lol thanks Joe.

Bump 1


Someone buys block/head, will part out the rest.

[BoostinIX]

Timmah!!! Bump

Make a short/long block offer, take it home

[worr20]

Lmk about the manifold if you decide to part.

[[email protected]]

Bump for good seller and legit setup! I have seen this run in person and it runs with no hiccups and smooth power! GLWS!

[S13drifterr18]

hey you down to trade for a 89 240sx? sr20 swap also? 240sx sr20det (http://newjersey.craigslist.org/cto/3776892622.html)

[[email protected]]

hey you down to trade for a 89 240sx? sr20 swap also? 240sx sr20det (http://newjersey.craigslist.org/cto/3776892622.html)

Why would he trade a built SR20 for a SR20? He said he would only trade for a T56 trans

[SmokeCircle]

intersted in parting out the engine/trans/turbo? i wouldn't need ic, rad, harness and all that other jazzz

[[email protected]]

hey you down to trade for a 89 240sx? sr20 swap also? 240sx sr20det (http://newjersey.craigslist.org/cto/3776892622.html)

Going LS.

$6k, partial trade for t56. If motor is bought/paid for, will part the rest.



Lol at people not knowing how to read.

[BoostinIX]

Haha Nick, partout will start after 7/27 (last show commitment). You know what's in it, pm me with an offer and claim it. Long blocks the hardest thing on it to sell so, yes I'm interested lol