BoostinIX
05-30-2013, 01:21 PM
Going LS, testing waters on selling the turnkey. Everything you'll need to install and drive is here.
S14SR -
.20 over.
Scat Rods, CP Pistons, acl bearings, polished crank. Apexi MHG. Head had seals and guides replaced. Water + oil pump were replaced along with timing kit. Essentially everything was new or refreshed at time of build, has under 10k miles on it.
Tomei M7960 turbo, Expreme mani/elbow, RAS, oil pan, 740cc Injectors, CP cover, oil cap, N2 oil filter adapter
RS*R downpipe
Wiring Specialties premade harness S14SR -> S14
Nismo motor/trans mount
Z32 Maf/Apexi intake
Blitz SBC-ID Spec R / Power meter
Blitz FMIC w/ sunk in piping to sit between frame sections
Blitz Hotpipe/VD BOV
GKTech Throttle pulley
B&M Short shifter / Competition Clutch and Flywheel / Nismo Slave + Pivot / DSS aluminum driveshaft
Stance water pulley / DIF water neck adapter
CodyAce AC Bracket
Enjuku Exh. Manifold studs / 7layer gasket.
Ceramic coating on manifold/elbow
ARP Flywheel and head bolts
CS remote oil filter setup
Nistune ECU
Mishimoto X-Line 3 core radiator / Mishimoto fans & shroud / Samco hoses
350hp/343 tq
1997 Nissan 240SX dyno run - YouTube (http://www.youtube.com/watch?v=GRx9JFhqN3I)
GRx9JFhqN3I
http://distilleryimage0.s3.amazonaws.com/e26b5462851e11e294d322000a1f8c09_7.jpg
Not parting, reeeeeally not looking to ship.
$6k
S14SR -
.20 over.
Scat Rods, CP Pistons, acl bearings, polished crank. Apexi MHG. Head had seals and guides replaced. Water + oil pump were replaced along with timing kit. Essentially everything was new or refreshed at time of build, has under 10k miles on it.
Tomei M7960 turbo, Expreme mani/elbow, RAS, oil pan, 740cc Injectors, CP cover, oil cap, N2 oil filter adapter
RS*R downpipe
Wiring Specialties premade harness S14SR -> S14
Nismo motor/trans mount
Z32 Maf/Apexi intake
Blitz SBC-ID Spec R / Power meter
Blitz FMIC w/ sunk in piping to sit between frame sections
Blitz Hotpipe/VD BOV
GKTech Throttle pulley
B&M Short shifter / Competition Clutch and Flywheel / Nismo Slave + Pivot / DSS aluminum driveshaft
Stance water pulley / DIF water neck adapter
CodyAce AC Bracket
Enjuku Exh. Manifold studs / 7layer gasket.
Ceramic coating on manifold/elbow
ARP Flywheel and head bolts
CS remote oil filter setup
Nistune ECU
Mishimoto X-Line 3 core radiator / Mishimoto fans & shroud / Samco hoses
350hp/343 tq
1997 Nissan 240SX dyno run - YouTube (http://www.youtube.com/watch?v=GRx9JFhqN3I)
GRx9JFhqN3I
http://distilleryimage0.s3.amazonaws.com/e26b5462851e11e294d322000a1f8c09_7.jpg
Not parting, reeeeeally not looking to ship.
$6k